Date: Thu, 22 Jun 2000 16:24:28 +0200 (CEST) From: Rasmus Skaarup <rasmus@gal.dk> To: Andrew Gallatin <gallatin@cs.duke.edu> Cc: freebsd-alpha@FreeBSD.ORG Subject: Re: Problems installing FreeBSD 4.0-RELEASE on an Alpha system Message-ID: <Pine.BSF.4.21.0006221539150.75717-100000@skaarup.org> In-Reply-To: <14674.5562.557540.469184@grasshopper.cs.duke.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, 22 Jun 2000, Andrew Gallatin wrote:
>
> Rasmus Skaarup writes:
> >
> > Hi,
> >
> > I'm not sure where to post this, I tried freebsd-questions, but didn't get
> > any responses.
> >
> > When trying to boot the system, with to to installation floppies, it
> > enters an infinite loop with the following output:
>
> Can you tell us what sort of system this is? Please include complete
> boot output, output from the SRM console's 'show conf' command
> (>>> show conf) or both.
It is a DS20E, with a single 500MHz CPU.
Here goes..
** snip snip **
P00>>>sh conf
COMPAQ AlphaServer DS20E 500 MHz
SRM Console: V5.6-3
PALcode: OpenVMS PALcode V1.69-54, Tru64 UNIX PALcode V1.62-55
Processors
CPU 0 Alpha 21264-7 500 MHz SROM Revision: V1.82
Bcache size: 4 MB
Core Logic
Cchip DECchip 21272-CA Rev 2.1
Dchip DECchip 21272-DA Rev 2.0
Pchip 0 DECchip 21272-EA Rev 2.2
Pchip 1 DECchip 21272-EA Rev 2.2
TIG Rev 4.22
Arbiter Rev 2.16 (0x1)
MEMORY
Array # Size Base Addr
------- ---------- ---------
0 1024 MB 000000000
Total Bad Pages = 0
Total Good Memory = 1024 MBytes
PCI Hose 00
Bus 00 Slot 05/0: Cypress 82C693
Bridge to Bus 1,
ISA
Bus 00 Slot 05/1: Cypress 82C693 IDE
dqa.0.0.105.0
dqa0.0.0.105.0 CD-224E
Bus 00 Slot 05/2: Cypress 82C693 IDE
dqb.0.1.205.0
Bus 00 Slot 05/3: Cypress 82C693 USB
Bus 00 Slot 06/0: Adaptec AIC-7895
pkb0.7.0.6.0 SCSI Bus ID 7
Bus 00 Slot 06/1: Adaptec AIC-7895
pkc0.7.0.106.0 SCSI Bus ID 7
PCI Hose 01
Bus 00 Slot 07: NCR 53C895
pka0.7.0.7.1 SCSI Bus ID 7
dka0.0.0.7.1 RZ2DD-LS
dka100.1.0.7.1 RZ2DD-LS
Bus 00 Slot 08: DEGPA-SA
Bus 00 Slot 09: DE500-BA Network Controller
ewa0.0.0.9.1 08-00-2B-C3-FF-2D
ISA
Slot Device Name Type Enabled BaseAddr IRQ
DMA
0
0 MOUSE Embedded Yes 60 12
1 KBD Embedded Yes 60 1
2 COM1 Embedded Yes 3f8 4
3 COM2 Embedded Yes 2f8 3
4 LPT1 Embedded Yes 3bc 7
5 FLOPPY Embedded Yes 3f0 6 2
P00>>>
** snip snip **
FreeBSD boot..:
** snip snip **
P00>>>b dva
(boot dva0.0.0.0.0 -flags A)
block 0 of dva0.0.0.0.0 is a valid boot block
reading 15 blocks from dva0.0.0.0.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 3ff66000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Loading /boot/loader
Console: SRM firmware console
VMS PAL rev: 0x2003600010145
OSF PAL rev: 0x200370002013e
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM disk boot, Revision 0.1
(jkh@beast.freebsd.org, Mon Mar 20 21:08:53 GMT 2000)
Memory: 1048576 k
> load /kernel
/kernel data=0x2affe0+0x231f8 \
> echo \007\007
> echo Please insert MFS root floppy and press enter:
Please insert MFS root floppy and press enter:
> read
> load -t mfs_root /mfsroot
> echo \007\007
> autoboot 10
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [kernel]...
Entering kernel at 0xfffffc0000325c20...
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-RELEASE #0: Mon Mar 20 22:26:00 GMT 2000
jkh@beast.freebsd.org:/usr/src/sys/compile/BOOTMFS
ST6600
COMPAQ AlphaServer DS20E 500 MHz, 500MHz
8192 byte page size, 1 processor.
CPU: EV6 (21264) major=8 minor=7 extensions=0x303<BWX,FIX,MVI,PRECISE>
OSF PAL rev: 0x200370002013e
real memory = 1071005696 (1045904K bytes)
avail memory = 1038319616 (1013984K bytes)
Preloaded elf kernel "kernel" at 0xfffffc00008a6000.
Preloaded mfs_root "/mfsroot" at 0xfffffc00008a60a0.
md0: Preloaded image </mfsroot> 2949120 bytes at 0xfffffc00005d31d8
md1: Malloc disk
pcib0: <21271 PCI host bus adapter> on tsunami0
pci0: <PCI bus> on pcib0
isab0: <Cypress 82C693 PCI-ISA bridge> at device 5.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Cypress 82C693 ATA controller> port
0x10200-0x1020f,0x3f4-0x3f7,0x1f0-0x1f7 irq 238 at device 5.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
atapci1: <Cypress 82C693 ATA controller> port 0x374-0x377,0x170-0x177 irq
239 at device 5.2 on pci0
atapci1: Busmastering DMA not supported
pci0: <Cypress 82C693 ATA controller> at 5.3 irq 234
ahc0: <Adaptec aic7895 Ultra SCSI adapter> port 0x10000-0x100ff mem
0x1021000-0x1021fff irq 19 at device 6.0 on pci0
ahc0: aic7895 Wide Channel A, SCSI Id=7, 255 SCBs
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
ahc0: interrupting at TSUNAMI irq 19
ahc1: <Adaptec aic7895 Ultra SCSI adapter> port 0x10100-0x101ff mem
0x1022000-0x1022fff irq 18 at device 6.1 on pci0
ahc1: aic7895 Wide Channel B, SCSI Id=7, 255 SCBs
ahc1: Host Adapter Bios disabled. Using default SCSI device parameters
ahc1: interrupting at TSUNAMI irq 18
pcib1: <21271 PCI host bus adapter> on tsunami0
pci1: <PCI bus> on pcib1
sym0: <895> port 0x80010000-0x800100ff mem
0x81064000-0x81064fff,0x81065000-0x810650ff irq 47 at device 7.0 on pci1
sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: interrupting at TSUNAMI irq 47
pci1: <unknown card> (vendor=0x12ae, dev=0x0001) at 8.0 irq 43
dc0: <Intel 21143 10/100BaseTX> port 0x80010100-0x8001017f mem
0x81065100-0x8106517f irq 39 at device 9.0 on pci1
dc0: interrupting at TSUNAMI irq 39
dc0: Ethernet address: 08:00:2b:c3:ff:2d
miibus0: <MII bus> on dc0
dcphy0: <Intel 21143 NWAY media interface> on miibus0
dcphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: interrupting at ISA irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd0: interrupting at ISA irq 1
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A, console
sio0: interrupting at ISA irq 4
sio1: reserved for low-level i/o
sym0:0: ERROR (81:0) (0-0-0) (0/7) @ (script 140:00000000).
sym0: script cmd = 808cfd02
sym0: regdump: ca 00 40 07 47 00 00 0f 00 08 00 00 80 00 08 0a 00 40 1e bf
20 ff ff ff.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0:0: ERROR (81:0) (0-0-0) (0/7) @ (script 140:00000000).
sym0: script cmd = 808cfd02
sym0: regdump: ca 00 40 07 47 00 00 0f 00 08 00 00 80 00 08 0a 00 40 1e bf
20 ff ff ff.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0:0: ERROR (81:0) (0-0-0) (0/7) @ (script 140:00000000).
sym0: script cmd = 808cfd02
sym0: regdump: ca 00 40 07 47 00 00 0f 00 08 00 00 80 00 08 0a 00 40 1e bf
20 ff ff ff.
(noperiph:sym0:0:-1:-1): SCSI BUS reset detected.
sym0:0: ERROR (81:0) (0-0-0) (0/7) @ (script 140:00000000).
** snip snip **
Thank you for your help.
Best regards
Rasmus
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0006221539150.75717-100000>