Date: Sat, 8 Mar 2014 12:36:47 -0700 From: Warner Losh <imp@bsdimp.com> To: Tom Everett <tom@khubla.com> Cc: "freebsd-arm@freebsd.org" <freebsd-arm@freebsd.org> Subject: Re: crash starting wandboard-quad with latest code Message-ID: <AAB174E5-08D6-4E69-B756-0AFA55B88C83@bsdimp.com> In-Reply-To: <CAB3ij4B%2B0BHYah4mOsek8BmLV1eavVnAisqOT8-_PMM%2B1rnPcw@mail.gmail.com> References: <CAB3ij4B%2B0BHYah4mOsek8BmLV1eavVnAisqOT8-_PMM%2B1rnPcw@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Mar 8, 2014, at 12:29 PM, Tom Everett <tom@khubla.com> wrote: > I've done a build of the wandboard-quad with svn version r262929 >=20 > Strangely, it now just stops, with no serial console output during the > boot. The complete boot log is below. My previous build with source > revision r262820 worked perfectly. >=20 > Any suggestions about what might be happening? No idea, but perhaps you could bisect? I did a change to the serial code last night that shouldn=92t have been a problem. Try r2626919 = maybe? Warner >=20 > .. >=20 >=20 > U-Boot 2013.10 (Mar 08 2014 - 11:53:29) >=20 >=20 > CPU: Freescale i.MX6Q rev1.2 at 792 MHz >=20 > Reset cause: POR >=20 > Board: Wandboard >=20 > DRAM: 2 GiB >=20 > MMC: FSL_SDHC: 0, FSL_SDHC: 1 >=20 > *** Warning - bad CRC, using default environment >=20 >=20 > In: serial >=20 > Out: serial >=20 > Err: serial >=20 > Net: FEC [PRIME] >=20 > Hit any key to stop autoboot: 5 ... 4 ... 3 ... 2 ... 1 ... 0 >=20 > mmc0 is current device >=20 > reading boot.scr >=20 > 157 bytes read in 10 ms (14.6 KiB/s) >=20 > Running bootscript from mmc ... >=20 > ## Executing script at 12000000 >=20 > reading ubldr >=20 > 253278 bytes read in 28 ms (8.6 MiB/s) >=20 > ## Starting application at 0x88000054 ... >=20 > Consoles: U-Boot console >=20 >=20 > Compatible API signature found @8f5756f8 >=20 >=20 > MMC: no card present >=20 > MMC Device 2 not found >=20 > MMC Device 3 not found >=20 > Number of U-Boot devices: 2 >=20 >=20 >=20 >=20 >=20 > FreeBSD/armv6 U-Boot loader, Revision 1.2 >=20 >=20 > (tom@bernice, Sat Mar 8 11:53:22 MST 2014) >=20 >=20 > DRAM: 2048MB >=20 >=20 > Probing for bootable devices... >=20 >=20 > Bootable device: disk >=20 >=20 > Bootable device: net >=20 >=20 > Current device: disk >=20 >=20 > |./.-.\.|./.-.\.|./.-.\.|./.-. >=20 >=20 > \.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-./boot/kernel/kernel > data=3D0x4dc0c8+0x2ff38 > = \.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.= |./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|.= /.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.= -.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.= \.|./.-.\.|./.-.\.syms=3D[0x4+0x7e6e0|./.-.\.|./.-.\.|./.-.\.|./.-.\.+0x4+= 0x4e0a1|./.-.\.|./.-.\.|.] >=20 >=20 > Hit [Enter] to boot immediately, or any other key for command prompt. >=20 >=20 >=20 > Booting [/boot/kernel/kernel] in 9 seconds... > Booting [/boot/kernel/kernel] in 8 seconds... > Booting [/boot/kernel/kernel] in 7 seconds... > Booting [/boot/kernel/kernel] in 6 seconds... > Booting [/boot/kernel/kernel] in 5 seconds... > Booting [/boot/kernel/kernel] in 4 seconds... > Booting [/boot/kernel/kernel] in 3 seconds... > Booting [/boot/kernel/kernel] in 2 seconds... > Booting [/boot/kernel/kernel] in 1 second... > Booting [/boot/kernel/kernel]... >=20 >=20 > /.-.\.|./.-.\.|./.-.\.|./.-.\.|./.Loaded DTB from file = 'wandboard-quad.dtb'. >=20 >=20 > -.\.|./.-.\.|.Kernel entry at 0x12000100... >=20 >=20 > Kernel args: (null) >=20 >=20 > KDB: debugger backends: ddb > KDB: current backend: ddb > Copyright (c) 1992-2014 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, = 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 11.0-CURRENT #0 r262929: Sat Mar 8 11:47:07 MST 2014 > = tom@bernice:/storage/home/tom/crochet/crochet-freebsd/work/obj/arm.armv6/s= torage/home/tom/crochet/src/FreeBSDHead/head/sys/IMX6 > arm > FreeBSD clang version 3.4 (tags/RELEASE_34/final 197956) 20140216 > CPU: Cortex A9-r2 rev 10 (Cortex-A core) > Supported features: ARM_ISA THUMB2 JAZELLE THUMBEE ARMv4 Security_Ext > WB disabled EABT branch prediction enabled > LoUU:2 LoC:1 LoUIS:2 > Cache level 1: > 32KB/32B 4-way data cache WB Read-Alloc Write-Alloc > 32KB/32B 4-way instruction cache Read-Alloc > real memory =3D 2147483648 (2048 MB) > avail memory =3D 2093953024 (1996 MB) > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > random device not loaded; using insecure entropy > random: <Software, Yarrow> initialized > ofwbus0: <Open Firmware Device Tree> > simplebus0: <Flattened device tree simple bus> on ofwbus0 > gic0: <ARM Generic Interrupt Controller> mem > 0xa01000-0xa01fff,0xa00100-0xa001ff on simplebus0 > gic0: pn 0x390, arch 0x1, rev 0x2, implementer 0x43b sc->nirqs 160 > l2cache0: <PL310 L2 cache controller> mem 0xa02000-0xa02fff irq 124 on > simplebus0 > l2cache0: Part number: 0x3, release: 0x7 > l2cache0: L2 Cache: 1024KB/32B 16 ways > l2cache0: L2 Cache enabled > simplebus1: <Flattened device tree simple bus> mem 0x2000000-0x20fffff = on > simplebus0 > ccm0: <Freescale i.MX6 Clock Control Module> mem 0x20c4000-0x20c7fff = irq > 119,120 on simplebus1 > imx6_anatop0: <Freescale i.MX6 Analog PLLs and Power> mem > 0x20c8000-0x20c8fff irq 49 on simplebus1 > imx6_anatop0: voltage set to 1225 > imx6_anatop0: CPU frequency 984MHz > imx_gpt0: <Freescale i.MX GPT timer> mem 0x2098000-0x209bfff irq 87 on > simplebus1 > Event timer "iMXGPT" frequency 11000000 Hz quality 800 > Timecounter "iMXGPT" frequency 11000000 Hz quality 1000 > uart0: <imx_uart> mem 0x2020000-0x2023fff irq 58 on simplebus1 > uart0: console (0,n,8,1) > usbphy0: <Freescale i.MX6 USB PHY> mem 0x20c9000-0x20c9fff irq 44 on > simplebus1 > usbphy1: <Freescale i.MX6 USB PHY> mem 0x20ca000-0x20cafff irq 45 on > simplebus1 > simplebus2: <Flattened device tree simple bus> mem 0x2100000-0x21fffff = on > simplebus0 > ffec0: <Freescale Gigabit Ethernet Controller> mem 0x2188000-0x218bfff = irq > 150,151 on simplebus2 > miibus0: <MII bus> on ffec0 > atphy0: <Atheros F1 10/100/1000 PHY> PHY 1 on miibus0 > atphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, > 1000baseSX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto > ffec0: Ethernet address: 00:1f:7b:b4:06:7f > ehci0: <Freescale i.MX integrated USB controller> mem = 0x2184000-0x21841ff > irq 75 on simplebus2 > ehci0: [GIANT-LOCKED] > usbus0: EHCI version 1.0 > usbus0 on ehci0 > ehci1: <Freescale i.MX integrated USB controller> mem = 0x2184200-0x21843ff > irq 72 on simplebus2 > ehci1: [GIANT-LOCKED] > usbus1: EHCI version 1.0 > usbus1 on ehci1 > sdhci_imx0: <Freescale uSDHC controller> mem 0x2190000-0x2193fff irq = 54 on > simplebus2 > mmc0: <MMC/SD bus> on sdhci_imx0 > sdhci_imx1: <Freescale uSDHC controller> mem 0x2198000-0x219bfff irq = 56 on > simplebus2 > mmc1: <MMC/SD bus> on sdhci_imx1 > ocotp0: <Freescale On-Chip One-Time-Programmable Memory> mem > 0x21bc000-0x21bffff on simplebus2 > Timecounters tick every 4.000 msec > usbus0: 480Mbps High Speed USB v2.0 > usbus1: 480Mbps High Speed USB v2.0 > ugen0.1: <Freescale> at usbus0 > uhub0: <Freescale EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on = usbus0 > ugen1.1: <Freescale> at usbus1 > uhub1: <Freescale EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on = usbus1 > mmc0: No compatible cards found on bus > mmcsd0: 16GB <SDHC SA16G 1.0 SN 663902625 MFG 12/2011 by 2 TM> at mmc1 > 50.0MHz/4bit/65535-block > random: unblocking device. > Release APs > uhub0: 1 port with 1 removable, self powered > uhub1: 1 port with 1 removable, self powered > Spurious interrupt detected [0x000003ff] > ugen1.2: <vendor 0x7392> at usbus1 > Trying to mount root from ufs:/dev/mmcsd0s2a [rw,noatime]... > warning: no time-of-day clock registered, system time will not be set > accurately >=20 >=20 >=20 >=20 > --=20 > A better world shall emerge based on faith and understanding - = Douglas > MacArthur > _______________________________________________ > freebsd-arm@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-arm > To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?AAB174E5-08D6-4E69-B756-0AFA55B88C83>