Date: Wed, 24 Oct 2001 04:20:39 -0400 From: "Bezerker" <bezerker@bezerker.org> To: "Patrick O'Reilly" <patrick@mip.co.za> Cc: <questions@freebsd.org> Subject: Re: Lil help with dummynet please? Message-ID: <00cd01c15c64$c5484f60$0101a8c0@bezerker> References: <NDBBIMKICMDGDMNOOCAIGEAHDMAA.patrick@mip.co.za>
next in thread | previous in thread | raw e-mail | index | archive | help
DOH! So sorry, i meant ipfw add pipe 1 which put the rule in line 65100.. does this rule need to be further up in the priority? Again sorry for that misinformation bleh ----- Original Message ----- From: "Patrick O'Reilly" <patrick@mip.co.za> To: "Bezerker" <bezerker@bezerker.org> Cc: <questions@FreeBSD.ORG> Sent: Wednesday, October 24, 2001 4:14 AM Subject: RE: Lil help with dummynet please? > Bez, > > I'm not sure if you are getting the syntax right in your firewall scripts, > but the samples in your emails are certainly not right. > > Below you mention a rule like this: > ipfw pipe 1 ip from any to 192.168.1.5 > > ipfw will see this as a pipe config rule, NOT a normal ipfw rule, because it > begins with "ipfw pipe". > > Try the following: > > ipfw pipe 1 config 3KByte/s > ipfw add 1 pipe 1 ip from any to 192.168.1.5 > > PS: I'm assuming you are running NAT? Make sure the rule sending packets to > the pipe is after NAT has done its trick, or else you are not going to get a > match on that private address! So perhaps you should rather do something > like this: > > ipfw pipe 1 config 3KByte/s > ipfw add 1 divert ip from any to any via tun0 > ipfw add 2 pipe 1 ip from any to 192.168.1.5 > > Patrick. > > > > -----Original Message----- > > From: owner-freebsd-questions@FreeBSD.ORG > > [mailto:owner-freebsd-questions@FreeBSD.ORG]On Behalf Of Bezerker > > Sent: 24 October 2001 09:45 > > To: Patrick O'Reilly > > Cc: questions@FreeBSD.ORG > > Subject: Re: Lil help with dummynet please? > > > > > > it listed fine, > > i even tried another rule of ipfw pipe 1 ip from any to > > 192.168.1.5 to limit > > ANY traffic going there to 3kbyte/S > > > > No go. > > I essentially, have my modem on tun0 (ppp ) .. and want to limit > > any traffic > > coming in via the modem going to my pop's machine, to 3kbyte a sec... > > unfortunately, that seems more complicated than i expected :P > > > > ----- Original Message ----- > > From: "Patrick O'Reilly" <patrick@mip.co.za> > > To: "Bezerker" <bezerker@bezerker.org>; <questions@FreeBSD.ORG> > > Sent: Wednesday, October 24, 2001 3:41 AM > > Subject: RE: Lil help with dummynet please? > > > > > > > > > > > > Im trying to setup bandwith limiting so my fathers machine dont > > > > soak all the > > > > bandwith on my itty 56k. > > > > > > > > so.. i do the dummynet stuff and do this > > > > ipfw add 1 ip from any to 192.168.1.5 via tun0 > > > > ipfw pipe 1 config bw 3Kbytes/s > > > > All looks well > > > > > > No, not so well. > > > > > > Your pipe config looks fine: > > > > ipfw pipe 1 config bw 3Kbytes/s > > > > > > But, to use the pipe, your ipfw rule should be: > > > > ipfw add 1 pipe 1 ip from any to 192.168.1.5 via tun0 > > > > > > In fact, the rule as you gave it above has invalid syntax as > > far as I can > > > tell, so it might not be active at all. Check with "ipfw list". > > > > > > Regards, > > > Patrick. > > > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > > with "unsubscribe freebsd-questions" in the body of the message > > > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-questions" in the body of the message > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?00cd01c15c64$c5484f60$0101a8c0>