Date: Mon, 11 Aug 2003 10:20:47 +0200 From: Igor Pokrovsky <igor.pokrovsky@cnrm.meteo.fr> To: freebsd-stable@freebsd.org Subject: support of SMBus on ICH3 Message-ID: <20030811082047.GA2111@exmatis1.cnrm.meteo.fr>
next in thread | raw e-mail | index | archive | help
Hello all,
I have problems with enabling support for SMBus on STABLE.
My motherboard is ICH3 (82801CA).
As suggested in LINT I added 3 lines to my kernel config:
device smbus
device ichsmb
device smb
But after compiling, installing and rebooting /dev/smb[01] are
not available and no changes in kernel startup messages either.
So I assume something hasn't been detected. I will provide any
additional info if needed.
Any suggestion or thoughts?
# dmesg:
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.8-STABLE #0: Sun Aug 10 20:08:36 CEST 2003
root@exmatis1.xxx.xxx:/usr/src/sys/compile/KERNEL
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.00GHz (2000.08-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf24 Stepping = 4
Features=0x3febf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
real memory = 268406784 (262116K bytes)
avail memory = 255754240 (249760K bytes)
Preloaded elf kernel "kernel" at 0xc03c7000.
Preloaded elf module "linux.ko" at 0xc03c709c.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 6 entries at 0xc00f13b0
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82845 Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82845 host to AGP bridge> mem 0xe0000000-0xefffffff at device 0.0 on pci0
pcib1: <Intel 82845 PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
drm0: <ATI Radeon LW Mobility 7500 M7> port 0xd800-0xd8ff mem 0xd7000000-0xd700ffff,0xd8000000-0xdfffffff irq 5 at device 0.0 on pci1
info: [drm] AGP at 0xe0000000 256MB
info: [drm] Initialized radeon 1.8.0 20020828 on minor 0
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xb800-0xb81f irq 5 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0xb400-0xb41f irq 9 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pcib2: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
rl0: <RealTek 8139 10/100BaseTX> port 0xa800-0xa8ff mem 0xd6800000-0xd68000ff irq 9 at device 5.0 on pci2
rl0: Ethernet address: 00:e0:18:9a:3d:a6
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
chip0: <PCI to CardBus bridge (vendor=1180 device=0476)> irq 5 at device 7.0 on pci2
chip1: <PCI to CardBus bridge (vendor=1180 device=0476)> irq 11 at device 7.1 on pci2
pci2: <unknown card> (vendor=0x1180, dev=0x0552) at 7.2 irq 9
isab0: <PCI to ISA bridge (vendor=8086 device=248c)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0x8400-0x840f,0x8800-0x8803,0x9000-0x9007,0x9400-0x9403,0x9800-0x9807 mem 0xd5800000-0xd58003ff irq 9 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcm0: <Intel 82801CA (ICH3)> port 0xe100-0xe13f,0xe000-0xe0ff irq 11 at device 31.5 on pci0
pcm0: <Cirrus Logic CS4299D/E/F/G/H ac97 codec>
pci0: <unknown card> (vendor=0x8086, dev=0x2486) at 31.6 irq 11
orm0: <Option ROM> at iomem 0xc0000-0xcefff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 38154MB <IC25N040ATCS04-0> [77520/16/63] at ata0-master UDMA100
acd0: CD-RW <TOSHIBA DVD-ROM SD-R2102> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s3a
-ip
--
Whenever I hear anyone arguing for slavery, I feel a strong impulse to
see it tried on him personally.
-- A. Lincoln
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030811082047.GA2111>