Date: Wed, 7 Apr 1999 23:17:32 -0400 From: Natty Rebel <dervish@ikhala.tcimet.net> To: current@freebsd.org Subject: System hangs when booting with (update5) of ata/atapi driver Message-ID: <19990407231732.A350@ikhala.tcimet.net>
next in thread | raw e-mail | index | archive | help
my system hangs when booting with update5 of the ata/atapi driver with the following in my kernel config: controller ata0 device atadisk0 # ATA disks device atapifd0 # ATAPI floppy drives the boot messages: Probing for devices on PCI bus 0: chip0: <Host to PCI bridge (vendor=1039 device=5591)> rev 0x02 on pci0.0.0 ata-pci0: <Unknown PCI IDE Controller> rev 0xd0 int a irq 14 on pci0.0.1 ata-pci0: Busmastering DMA supported ata0 at 0x01f0 irq on ata-pci0 chip1: <SiS 85c503> rev 0x01 on pci0.1.0 chip2: <PCI to PCI bridge (vendor=1039 device=0001)> rev 0x00 on pci0.2.0 [snippage ...] ata0: master: setting up generic WDMA2 mode OK ad0: <FUJITSU MPB3032ATU/2011> ATA-3 disk at ata0 as master ad0: 3039MB (6335280 sectors), 6704 cyls, 15 heads, 63 S/T, 512 B/S ad0: piomode=4, dmamode=2, udmamode=2 ad0: 16 secs/int, 0 depth queue, DMA mode changing root device to wd0s1a and then the system hangs. pressing reset and booting /kernel.old brings it back to life. now with the following entries in my kernel config: controller wdc0 at isa? port "IO_WD1" bio irq 14 flags 0x80ff80ff disk wd0 at wdc0 drive 0 options ATAPI #Enable ATAPI support for IDE bus options ATAPI_STATIC #Don't do it as an LKM i get the following on boot and all is well ... Probing for devices on PCI bus 0: chip0: <Host to PCI bridge (vendor=1039 device=5591)> rev 0x02 on pci0.0.0 ide_pci0: <SiS 5591 Bus-master IDE Controller> rev 0xd0 int a irq 14 on pci0.0.1 chip1: <SiS 85c503> rev 0x01 on pci0.1.0 chip2: <PCI to PCI bridge (vendor=1039 device=0001)> rev 0x00 on pci0.2.0 [snip ...] wdc0 at 0x1f0-0x1f7 irq 14 flags 0x80ff80ff on isa wdc0: unit 0 (wd0): <FUJITSU MPB3032ATU>, 32-bit, multi-block-16 wd0: 3093MB (6335280 sectors), 6704 cyls, 15 heads, 63 S/T, 512 B/S my motherboard is a gigabyte ga-5sg11 with SIS 5591/5595 chipset.. hope this info is helpful ... #;^) -- natty rebel harder than the rest ... To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?19990407231732.A350>