Date: Mon, 22 May 2000 07:17:01 -0400 From: "Cameron, Frank" <cameron@ctc.com> To: "'freebsd-stable@freebsd.org'" <freebsd-stable@freebsd.org> Subject: ide cd not detected by 4.0-STABLE Message-ID: <E41DD2A84F21D411B567009027B0FD886C2A62@ctcjst-mail1.ctc.com>
next in thread | raw e-mail | index | archive | help
> I upgraded my home PC from 3.4 to 4.0 not long ago and > am having a problem with my ide cd-rom drive. > > My setup: > Primary > Master: 5G drive > Slave: 5G Drive > Secondary > Master: 24x CD-ROM > Slave: 2x CD-ROM > Tertiary: > on SoundBlaster, not used > > Under DOS, 95, and 3.4 the drive was detected and worked > just fine; but under 4.0 the drive detection times out: > ata1-master: ata_command: timeout waiting for intr > ata1-master: identify failed > > I booted once to my backup 3.4 kernel and the drive was > detected. > > Does anyone have any suggestions on making this work? > Thanks. > The next chance I get I'll cvsup and make world again to see if that helps. > -frank > > > Some excerpts from dmesg: > > FreeBSD 4.0-STABLE #49: Sat May 6 21:55:06 EDT 2000 > frank@tigger:/usr/src/sys/compile/FBSD_TIGGER > > atapci0: <VIA 82C586 ATA33 controller> port > 0xfff0-0xffff at device 7.1 on pci0 > > ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xfff0 > ata0: mask=03 status0=50 status1=50 > ata0: mask=03 status0=50 status1=50 > ata0: devices = 0x3 > ata0: at 0x1f0 irq 14 on atapci0 > > ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xfff8 > ata1: mask=03 status0=50 status1=50 > ata1: mask=03 status0=00 status1=00 > ata1: devices = 0xc > ata1: at 0x170 irq 15 on atapci0 > > ata2: iobase=0x0168 altiobase=0x036e bmaddr=0x0000 > ata2: mask=00 status0=ff status1=ff > ata2: probe allocation failed > unknown2: <Generic ESDI/IDE/ATA controller> at port > 0x168-0x16f,0x36e-0x36f irq 10 on isa0 > > BIOS Geometries: > 0:0271fe3f 0..625=626 cylinders, 0..254=255 heads, > 1..63=63 sectors > 1:026cfe3f 0..620=621 cylinders, 0..254=255 heads, > 1..63=63 sectors > 0 accounted for > Device configuration finished. > > ata1-master: ata_command: timeout waiting for intr > ata1-master: identify failed > > ata0-master: success setting up UDMA2 mode on VIA chip > ad0: <WDC AC35100L/08.09L08> ATA-4 disk at ata0 as > master > ad0: 4924MB (10085040 sectors), 10672 cyls, 15 heads, 63 > S/T, 512 B/S > ad0: 16 secs/int, 1 depth queue, UDMA33 > ad0: piomode=4 dmamode=2 udmamode=2 cblid=0 > Creating DISK ad0 > Creating DISK wd0 > > ata0-slave: success setting up WDMA2 mode on VIA chip > ad1: <Maxtor 85120A8/ZA8X0726> ATA-3 disk at ata0 as > slave > ad1: 4884MB (10002825 sectors), 10585 cyls, 15 heads, 63 > S/T, 512 B/S > ad1: 16 secs/int, 1 depth queue, WDMA2 > ad1: piomode=4 dmamode=2 udmamode=-1 cblid=0 > Creating DISK ad1 > Creating DISK wd1 > > ata1-slave: piomode=0 dmamode=0 udmamode=-1 dmaflag=1 > ata1-slave: success setting up PIO0 mode on generic chip > acd0: <CD-ROM CDU55E/1.0u> CDROM drive at ata1 as slave > acd0: read 344KB/s (344KB/s), 256KB buffer, PIO0 > acd0: Reads: CD-DA stream > acd0: Audio: play, 256 volume levels > acd0: Mechanism: ejectable tray > acd0: Medium: CD-ROM unknown medium, unlocked > > > ----------------------------------------------------- > This mail sent through IMP: http://web.horde.org/imp/ > > ----- End forwarded message ----- > > > ----------------------------------------------------- > This mail sent through IMP: http://web.horde.org/imp/ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?E41DD2A84F21D411B567009027B0FD886C2A62>