Date: Mon, 7 Jun 1999 08:11:08 -0400 (EDT) From: mwlucas@exceptionet.com To: mobile@freebsd.org Subject: xe0: watchdog timeout: resetting card Message-ID: <199906071211.IAA20468@easeway.com>
next in thread | raw e-mail | index | archive | help
Hello,
I just picked up a new Xircom CreditCard, to replace my broken EtherLink
III.
The laptop is a Toshiba 4015 CDS, running 3.2-BETA.
I downloaded the xe0 driver, installed it manually, copied in the kernel
config lines, built new kernel, configured pccardd, and brought it up. It
recognizes the card, brings it up, everything I could ask for.
Any time I send traffic, however, I receive nothing. The traffic light
blinks three or four times, then stops. The "watchdog" error appears.
The card is transmitting to the local ethernet; when I (accidentally)
configure the Xircom with an IP addressed used on my desktop box, the
desktop box gripes that someone is using its IP.
Any thoughts on what to check next? My dmesg, pccardc dumpcis, and
pccard.conf follow. (I know the pccard.conf entry for the modem is wrong;
I've never actually had need for the modem, and therefore haven't taken
time to figure it out. ;)
Thanks,
==ml
--
io 0x240-0x360
irq 8 9 10 11 13
memory 0xd4000 96k
card "Xircom" "CreditCard 10/100"
config 0x1 "xe0" 9
insert ifconfig xe0 up
remove ifconfig xe0 down
card "Toshiba America" "3CXM056-BNW"
config 0x1 "sio2" 10
--
Copyright (c) 1992-1999 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.2-BETA #3: Mon Jun 7 07:13:09 GMT 1999
mwlucas@moneysink.exceptionet.com:/usr/src/sys/compile/GEBURAH
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Xeon/Celeron (266.62-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x652 Stepping=2
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,<b24>>
real memory = 33554432 (32768K bytes)
avail memory = 30425088 (29712K bytes)
Preloaded elf kernel "kernel" at 0xc024f000.
Probing for devices on PCI bus 0:
chip0: <Intel 82443BX host to PCI bridge (AGP disabled)> rev 0x02 on pci0.0.0
chip1: <PCI to CardBus bridge (vendor=1179 device=060f)> rev 0x05 int a irq 255 on pci0.2.0
chip2: <PCI to CardBus bridge (vendor=1179 device=060f)> rev 0x05 int b irq 255 on pci0.2.1
vga0: <Chips & Technologies model 00e5 VGA-compatible display device> rev 0xc6 on pci0.4.0
chip3: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.7.0
ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1
chip4: <Intel 82371AB Power management controller> rev 0x02 on pci0.7.3
Probing for devices on PCI bus 1:
Probing for devices on PCI bus 2:
Probing for devices on PCI bus 3:
Probing for devices on PCI bus 4:
Probing for devices on PCI bus 5:
Probing for devices on PCI bus 6:
Probing for devices on PCI bus 7:
Probing for devices on PCI bus 8:
Probing for devices on PCI bus 9:
Probing for devices on PCI bus 10:
Probing for devices on PCI bus 11:
Probing for devices on PCI bus 12:
Probing for devices on PCI bus 13:
Probing for devices on PCI bus 14:
Probing for devices on PCI bus 15:
Probing for devices on PCI bus 16:
Probing for devices on PCI bus 17:
Probing for devices on PCI bus 18:
Probing for devices on PCI bus 19:
Probing for devices on PCI bus 20:
Probing for devices on PCI bus 21:
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
psm0 irq 12 on isa
psm0: model Generic PS/2 mouse, device ID 0
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
... try to identify the yamaha
pcm0 at 0x530 irq 5 drq 1 flags 0xa200 on isa
mss_attach <mss>0 at 0x530 irq 5 dma 1:1 flags 0xa200
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <IBM-DKLA-24320>
wd0: 4126MB (8452080 sectors), 8944 cyls, 15 heads, 63 S/T, 512 B/S
wdc1 at 0x170-0x177 irq 15 on isa
wdc1: unit 0 (atapi): <CD-224E/7.5A>, removable, accel, ovlap, dma, iordis
acd0: drive speed 4134KB/sec, 128KB cache
acd0: supported read types: CD-R, CD-DA
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
ppc0 at 0x378 irq 7 on isa
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <generic parallel i/o> on ppbus 0
plip0: <PLIP network interface> on ppbus 0
xe0 not found
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
apm0 flags 0x31 on isa
apm: found APM BIOS version 1.2
Initializing PC-card drivers: sio xe
changing root device to wd0s1a
--
Code 128 not found
Code 128 not found
code Unknown ignored
Code 131 not found
Code 131 not found
code Unknown ignored
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: 00 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x15 (Version 1 info), length = 57
000: 04 01 54 6f 73 68 69 62 61 20 41 6d 65 72 69 63
010: 61 00 33 43 58 4d 30 35 36 2d 42 4e 57 00 33 43
020: 4f 4d 2f 4e 6f 74 65 57 6f 72 74 68 79 20 35 36
030: 4b 20 4d 6f 64 65 6d 00 ff
Version = 4.1, Manuf = [Toshiba America],card vers = [3CXM056-BNW]
Addit. info = [3COM/NoteWorthy 56K Modem],[ÿ]
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
000: 01 01 2f 00
PCMCIA ID = 0x101, OEM ID = 0x2f
Tuple #4, code = 0x21 (Functional ID), length = 2
000: 02 01
Serial port/modem - POST initialize
Tuple #5, code = 0x1a (Configuration map), length = 5
000: 01 23 00 03 03
Reg len = 2, config register addr = 0x300, last config = 0x23
Registers: XX------
Tuple #6, code = 0x1b (Configuration entry), length = 16
000: e0 41 99 49 55 3e 3d aa 60 f8 03 07 30 ff ff 28
Config index = 0x20(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Continuous supply current: 3.5 x 100mA
Power down supply current: 3.5 x 10mA
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x3f8 block length = 0x8
IRQ modes: Level
IRQs: 4 5 8 9 10 11 12 13 14 15
Max twin cards = 0
Misc attr: (Audio-BVD2) (Power down supported)
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 21 08 aa 60 f8 02 07
Config index = 0x21
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x2f8 block length = 0x8
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 22 08 aa 60 e8 03 07
Config index = 0x22
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x3e8 block length = 0x8
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 23 08 aa 60 e8 02 07
Config index = 0x23
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x2e8 block length = 0x8
Tuple #10, code = 0x22 (Functional EXT), length = 4
000: 00 02 0f 7c
Serial interface extension:
16550 UART, Parity - Space,Mark,Odd,Even,
Tuple #11, code = 0x22 (Functional EXT), length = 9
000: 01 1f 0f 00 06 00 00 06 00
Modem interface capabilities:
Tuple #12, code = 0x22 (Functional EXT), length = 12
000: 02 06 00 3f 1c 03 03 0f 07 00 02 b5
Data modem services available:
Tuple #13, code = 0x22 (Functional EXT), length = 8
000: 13 06 00 0f 00 02 00 b5
Tuple #14, code = 0x22 (Functional EXT), length = 8
000: 23 06 00 0f 00 02 00 b5
Tuple #15, code = 0x0 (Null tuple), length = 10
000: 02 01 2f 00 21 00 07 00 00 ff
Tuple #16, code = 0x0 (Null tuple), length = 14
000: 31 30 39 4e 31 43 37 38 33 35 37 32 00 ff
Tuple #17, code = 0x14 (No link), length = 0
Tuple #18, code = 0xff (Terminator), length = 0
Code 136 not found
Code 136 not found
code Unknown ignored
code Manufacturer ID ignored
Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
000: 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 2
000: 00 ff
Attribute memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #3, code = 0x15 (Version 1 info), length = 44
000: 05 00 58 69 72 63 6f 6d 00 43 72 65 64 69 74 43
010: 61 72 64 20 31 30 2f 31 30 30 00 43 45 33 2d 31
020: 30 2f 31 30 30 00 31 2e 30 30 00 ff
Version = 5.0, Manuf = [Xircom],card vers = [CreditCard 10/100]
Addit. info = [CE3-10/100],[1.00]
Tuple #4, code = 0x0 (Null tuple), length = 8
000: f5 ee 72 00 00 00 00 00
Tuple #5, code = 0x0 (Null tuple), length = 5
000: 05 01 0a 01 43
Tuple #6, code = 0x44 (Card init date), length = 4
000: 9a 5c 5a 26
Tuple #7, code = 0x1a (Configuration map), length = 5
000: 01 01 00 08 03
Reg len = 2, config register addr = 0x800, last config = 0x1
Registers: XX------
Tuple #8, code = 0x1b (Configuration entry), length = 25
000: c1 c1 bd 7f 55 4d 5d 3e 46 46 06 e0 17 17 e4 60
010: 00 00 0f 70 bc 8e 10 00 20
Config index = 0x1(default)
Interface byte = 0xc1 (I/O) +RDY/-BSY active, wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Continuous supply current: 3.5 x 100mA
Max current average over 1 second: 4 x 100mA
Max current average over 10 ms: 4 x 100mA
Power down supply current: 1 x 100mA
Wait scale Speed = 1.2 x 10 ms
RDY/BSY scale Speed = 1.2 x 10 ms
Card decodes 23 address lines
IRQ modes:
IRQs: NMI IOCK BERR 0 1 2 4 8 9 10 12
Memory space length = 0x60
Max twin cards = 0
Misc attr:
Tuple #9, code = 0x21 (Functional ID), length = 2
000: 06 00
Network/LAN adapter
Tuple #10, code = 0x22 (Functional EXT), length = 8
000: 04 06 00 80 c7 f5 ee 72
Voice services available:
Tuple #11, code = 0x22 (Functional EXT), length = 2
000: 01 02
Modem interface capabilities:
Tuple #12, code = 0x22 (Functional EXT), length = 5
000: 02 80 96 98 00
Data modem services available:
Tuple #13, code = 0x22 (Functional EXT), length = 5
000: 02 00 e1 f5 05
Data modem services available:
Tuple #14, code = 0x22 (Functional EXT), length = 2
000: 03 01
Tuple #15, code = 0x22 (Functional EXT), length = 2
000: 03 03
Tuple #16, code = 0x22 (Functional EXT), length = 2
000: 05 00
Modem interface capabilities:
Tuple #17, code = 0xff (Terminator), length = 0
2 slots found
--
Michael Lucas |
Exceptionet, Inc. | www.exceptionet.com
"Exceptional Networking" |
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199906071211.IAA20468>