Date: Sun, 21 Feb 2016 18:09:05 -0700 From: Brett Glass <brett@lariat.net> To: freebsd-arm@freebsd.org Subject: Latest 11.0 snapshot won't boot on CUBOX either Message-ID: <201602220109.SAA20866@mail.lariat.net>
next in thread | raw e-mail | index | archive | help
After the experience described in my last message, I tried the
mid-February 11.0 snapshot (r295683). This one actually began to
use the video display, but did not boot whether or not I attached a
USB keyboard. A serial terminal showed the following:
U-Boot SPL 2013.10-rc4 (Feb 17 2016 - 08:14:06)
Boot Device: SD1
spl: error reading image u-boot.img, err - -1
Load image from RAW...
U-Boot 2013.10-rc4 (Feb 17 2016 - 08:14:06)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6-CuBox-i
DRAM: 1 GiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
** Unable to read file uEnv.txt **
Hit any key to stop autoboot: 0
Booting from: mmc 0 ubldr
262739 bytes read in 25 ms (10 MiB/s)
## Starting application at 0x12000094 ...
Consoles: U-Boot console
Compatible U-Boot API signature found @4f7708a8
FreeBSD/armv6 U-Boot loader, Revision 1.2
(root@releng2.nyi.freebsd.org, Wed Feb 17 08:37:47 UTC 2016)
DRAM: 1024MB
Number of U-Boot devices: 2
U-Boot env: loaderdev='mmc 0'
Found U-Boot device: disk
Checking unit=0 slice=<auto> partition=<auto>... good.
Booting from disk0s2a:
/boot/kernel/kernel data=0x6b6964+0xc969c syms=[0x4+0x7f460+0x4+0x91631]
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
/boot/dtb/imx6q-cubox-i.dtb size=0x89c9
Loaded DTB from file 'imx6q-cubox-i.dtb'.
Kernel entry at 0x12200100...
Kernel args: (null)
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-CURRENT #0 r295683: Wed Feb 17 08:44:44 UTC 2016
root@releng2.nyi.freebsd.org:/usr/obj/arm.armv6/usr/src/sys/IMX6 arm
FreeBSD clang version 3.7.1 (tags/RELEASE_371/final 255217) 20151225
VT: init without driver.
CPU: Cortex A9-r2 rev 10 (Cortex-A core)
Supported features: ARM_ISA THUMB2 JAZELLE THUMBEE ARMv4 Security_Ext
WB enabled LABT branch prediction disabled
LoUU:2 LoC:2 LoUIS:2
Cache level 1:
32KB/32B 4-way data cache WB Read-Alloc Write-Alloc
32KB/32B 4-way instruction cache Read-Alloc
real memory = 1073741824 (1024 MB)
avail memory = 1039437824 (991 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> mem
0x2000000-0x20fffff on simplebus0
simplebus2: <Flattened device tree simple bus> mem
0x2000000-0x203ffff on simplebus1
imx6_anatop0: <Freescale i.MX6 Analog PLLs and Power> mem
0x20c8000-0x20c8fff irq 43,44,45 on simplebus1
simplebus3: <Flattened device tree simple bus> mem
0x2100000-0x21fffff on simplebus0
ocotp0: <Freescale On-Chip One-Time-Programmable Memory> mem
0x21bc000-0x21bffff on simplebus3
ccm0: <Freescale i.MX6 Clock Control Module> mem
0x20c4000-0x20c7fff irq 41,42 on simplebus1
l2cache0: <PL310 L2 cache controller> mem 0xa02000-0xa02fff irq 6 on simplebus0
l2cache0: Part number: 0x3, release: 0x7
l2cache0: L2 Cache enabled: 1024KB/32B 16 ways
imx_iomux0: <Freescale i.MX pin configuration> mem
0x20e0000-0x20e3fff on simplebus1
gic0: <ARM Generic Interrupt Controller> mem
0xa01000-0xa01fff,0xa00100-0xa001ff on simplebus0
gic0: pn 0x390, arch 0x1, rev 0x2, implementer 0x43b irqs 160
imx_gpt0: <Freescale i.MX GPT timer> mem 0x2098000-0x209bfff irq 23
on simplebus1
Event timer "iMXGPT" frequency 66000000 Hz quality 800
Timecounter "iMXGPT" frequency 66000000 Hz quality 1000
mp_tmr0: <ARM MPCore Timers> mem 0xa00600-0xa0061f irq 5 on simplebus0
Event timer "MPCore" frequency 492000000 Hz quality 1000
hdmi0: <Freescale i.MX6 HDMI core> mem 0x120000-0x128fff irq 2 on simplebus0
hdmi0: HDMI controller 13:0a:a0:c1
uart0: <Freescale i.MX UART> mem 0x2020000-0x2023fff irq 62 on simplebus2
uart0: console (115200,n,8,1)
gpio0: <Freescale i.MX GPIO Controller> mem 0x209c000-0x209ffff irq
24,25 on simplebus1
gpiobus0: <GPIO bus> on gpio0
gpioc0: <GPIO controller> on gpio0
gpio1: <Freescale i.MX GPIO Controller> mem 0x20a0000-0x20a3fff irq
26,27 on simplebus1
gpiobus1: <GPIO bus> on gpio1
gpioc1: <GPIO controller> on gpio1
gpio2: <Freescale i.MX GPIO Controller> mem 0x20a4000-0x20a7fff irq
28,29 on simplebus1
gpiobus2: <GPIO bus> on gpio2
gpioc2: <GPIO controller> on gpio2
gpio3: <Freescale i.MX GPIO Controller> mem 0x20a8000-0x20abfff irq
30,31 on simplebus1
gpiobus3: <GPIO bus> on gpio3
gpioc3: <GPIO controller> on gpio3
gpio4: <Freescale i.MX GPIO Controller> mem 0x20ac000-0x20affff irq
32,33 on simplebus1
gpiobus4: <GPIO bus> on gpio4
gpioc4: <GPIO controller> on gpio4
gpio5: <Freescale i.MX GPIO Controller> mem 0x20b0000-0x20b3fff irq
34,35 on simplebus1
gpiobus5: <GPIO bus> on gpio5
gpioc5: <GPIO controller> on gpio5
gpio6: <Freescale i.MX GPIO Controller> mem 0x20b4000-0x20b7fff irq
36,37 on simplebus1
gpiobus6: <GPIO bus> on gpio6
gpioc6: <GPIO controller> on gpio6
imx_wdog0: <Freescale i.MX Watchdog> mem 0x20bc000-0x20bffff irq 39
on simplebus1
usbphy0: <Freescale i.MX6 USB PHY> mem 0x20c9000-0x20c9fff irq 46 on simplebus1
usbphy1: <Freescale i.MX6 USB PHY> mem 0x20ca000-0x20cafff irq 47 on simplebus1
src0: <Freescale i.MX6 System Reset Controller> mem
0x20d8000-0x20dbfff irq 50,51 on simplebus1
ehci0: <Freescale i.MX integrated USB controller> mem
0x2184000-0x21841ff irq 69 on simplebus3
ehci0: [GIANT-LOCKED]
usbus0: EHCI version 1.0
usbus0 on ehci0
ehci1: <Freescale i.MX integrated USB controller> mem
0x2184200-0x21843ff irq 70 on simplebus3
ehci1: [GIANT-LOCKED]
usbus1: EHCI version 1.0
usbus1 on ehci1
ffec0: <Freescale Gigabit Ethernet Controller> mem
0x2188000-0x218bfff irq 73,74 on simplebus3
miibus0: <MII bus> on ffec0
atphy0: <Atheros F1 10/100/1000 PHY> PHY 0 on miibus0
atphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
1000baseSX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
ffec0: Ethernet address: d0:63:b4:00:18:99
sdhci_imx0: <Freescale uSDHC controller> mem 0x2190000-0x2193fff
irq 78 on simplebus3
mmc0: <MMC/SD bus> on sdhci_imx0
sdhci_imx1: <Freescale uSDHC controller> mem 0x2194000-0x2197fff
irq 79 on simplebus3
mmc1: <MMC/SD bus> on sdhci_imx1
iichb0: <Freescale i.MX I2C> mem 0x21a4000-0x21a7fff irq 83 on simplebus3
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
iichb1: <Freescale i.MX I2C> mem 0x21a8000-0x21abfff irq 84 on simplebus3
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
iicbus1: <unknown card> at addr 0xd0
uart1: <Freescale i.MX UART> mem 0x21f0000-0x21f3fff irq 91 on simplebus3
fb0: <Freescale IPU> mem 0x2400000-0x27fffff irq 9,10 on simplebus0
cryptosoft0: <software crypto>
Timecounters tick every 2.000 msec
IPsec: Initialized Security Association Processing.
hdmi0: reading EDID from iicbus0, addr 50
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Freescale> at usbus0
uhub0: <Freescale EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Freescale> at usbus1
uhub1: <Freescale EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
fbd0 on fb0
VT: initialize with new VT driver "fb".
uhub0: 1 port with 1 removable, self powered
uhub1: 1 port with 1 removable, self powered
sdhci_imx0-slot0: Controller timeout
sdhci_imx0-slot0: ============== REGISTER DUMP ==============
sdhci_imx0-slot0: Sys addr: 0x00000000 | Version: 0x00000002
sdhci_imx0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000001
sdhci_imx0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_imx0-slot0: Present: 0x00f90000 | Host ctl: 0x00000001
sdhci_imx0-slot0: Power: 0x0000000d | Blk gap: 0x00000080
sdhci_imx0-slot0: Wake-up: 0x00000008 | Clock: 0x0000fa07
sdhci_imx0-slot0: Timeout: 0x00000080 | Int stat: 0x00000001
sdhci_imx0-slot0: Int enab: 0x017f00fb | Sig enab: 0x017f00fb
sdhci_imx0-slot0: AC12 err: 0x00000000 | Slot int: 0x00000001
sdhci_imx0-slot0: Caps: 0x0377c800 | Max curr: 0x80000000
sdhci_imx0-slot0: ===========================================
sdhci_imx0-slot0: Controller timeout
sdhci_imx0-slot0: ============== REGISTER DUMP ==============
sdhci_imx0-slot0: Sys addr: 0x00000000 | Version: 0x00000002
sdhci_imx0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000001
sdhci_imx0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_imx0-slot0: Present: 0x00f90000 | Host ctl: 0x00000001
sdhci_imx0-slot0: Power: 0x0000000d | Blk gap: 0x00000080
sdhci_imx0-slot0: Wake-up: 0x00000008 | Clock: 0x0000fa07
sdhci_imx0-slot0: Timeout: 0x00000080 | Int stat: 0x00000001
sdhci_imx0-slot0: Int enab: 0x017f00fb | Sig enab: 0x017f00fb
sdhci_imx0-slot0: AC12 err: 0x00000000 | Slot int: 0x00000001
sdhci_imx0-slot0: Caps: 0x0377c800 | Max curr: 0x80000000
sdhci_imx0-slot0: ===========================================
sdhci_imx0-slot0: Controller timeout
sdhci_imx0-slot0: ============== REGISTER DUMP ==============
sdhci_imx0-slot0: Sys addr: 0x00000000 | Version: 0x00000002
sdhci_imx0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000001
sdhci_imx0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_imx0-slot0: Present: 0x00f90000 | Host ctl: 0x00000001
sdhci_imx0-slot0: Power: 0x0000000d | Blk gap: 0x00000080
sdhci_imx0-slot0: Wake-up: 0x00000008 | Clock: 0x0000fa07
sdhci_imx0-slot0: Timeout: 0x00000080 | Int stat: 0x00000001
sdhci_imx0-slot0: Int enab: 0x017f00fb | Sig enab: 0x017f00fb
sdhci_imx0-slot0: AC12 err: 0x00000000 | Slot int: 0x00000001
sdhci_imx0-slot0: Caps: 0x0377c800 | Max curr: 0x80000000
sdhci_imx0-slot0: ===========================================
...and similar messages ad infinitum. The lines after the one
beginning with "VT:" appeared on the VGA, but the bootstrap process
never completed. So, the only snapshot I have that will boot
completely is an old one from December.... Is there anything newer
or in the works that will boot? I would like to start developing on
this and contribute some code, but need a couple of systems to at
least be limping along to start.
--Brett Glass
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201602220109.SAA20866>