Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 2 May 2003 17:22:08 +0200
From:      Jon Lech Johansen <jon@nanocrew.net>
To:        freebsd-current@freebsd.org
Subject:   IBM ThinkPad T40 - ACPI and em0 checksum verification
Message-ID:  <20030502172207.A15705@nanocrew.net>

next in thread | raw e-mail | index | archive | help
Intel Pro/1000 MT Mobile

em0: The EEPROM Checksum Is Not Valid
em0: Unable to initialize the hardware

That's the em0 driver in HEAD. The version in RELENG_5_0 works fine.

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #0: Fri May  2 02:23:11 CEST 2003
    root@tp.nanocrew.net:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc06f3000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06f30a8.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 1598649445 Hz
CPU: Intel(R) Pentium(R) M processor 1600MHz (1598.65-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x695  Stepping = 5
  Features=0xa7e9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE>
real memory  = 1073086464 (1023 MB)
avail memory = 1035063296 (987 MB)
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <IBM    TP-1R   > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 15 entries at 0xc00fdea0
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__._INI] (Node 0xc6193720), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT0._STA] (Node 0xc6195e80), AE_NOT_EXIST
    ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT0._STA] (Node 0xc6195e80), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT1._STA] (Node 0xc6195d00), AE_NOT_EXIST
    ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT1._STA] (Node 0xc6195d00), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BGID] (Node 0xc619e260), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BINI] (Node 0xc619e280), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BSTA] (Node 0xc619b240), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.IDE0.SCND.MSTR._STA] (Node 0xc619e180), AE_NOT_EXIST
    ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.IDE0.SCND.MSTR._STA] (Node 0xc619e180), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.USB7._INI] (Node 0xc619b5a0), AE_AML_REGION_LIMIT
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast"  frequency 3579545 Hz
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT0._STA] (Node 0xc6195e80), AE_NOT_EXIST
    ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT0._STA] (Node 0xc6195e80), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT1._STA] (Node 0xc6195d00), AE_NOT_EXIST
    ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT1._STA] (Node 0xc6195d00), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BGID] (Node 0xc619e260), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BINI] (Node 0xc619e280), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BSTA] (Node 0xc619b240), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.IDE0.SCND.MSTR._STA] (Node 0xc619e180), AE_NOT_EXIST
    ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.IDE0.SCND.MSTR._STA] (Node 0xc619e180), AE_NOT_EXIST
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
    ACPI-1287: *** Error: Method execution failed [\\_SB_.LID_._PSW] (Node 0xc21b32a0), AE_NOT_EXIST
acpi_button0: <Sleep Button> on acpi0
    ACPI-1287: *** Error: Method execution failed [\\_SB_.SLPB._PSW] (Node 0xc21b3220), AE_NOT_EXIST
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel Generic host to PCI bridge> mem 0xd0000000-0xdfffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1800-0x181f irq 9 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1820-0x183f irq 11 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1840-0x185f irq 10 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
cbb0: <TI1520 PCI-CardBus Bridge> mem 0x50000000-0x50000fff irq 9 at device 0.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <TI1520 PCI-CardBus Bridge> mem 0x51000000-0x51000fff irq 5 at device 0.1 on pci2
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.5.31> port 0x8000-0x803f mem 0xc0200000-0xc020ffff,0xc0220000-0xc023ffff irq 9 at device 1.0 on pci2
em0: The EEPROM Checksum Is Not Valid
em0: Unable to initialize the hardware
device_probe_and_attach: em0 attach returned 5
pci2: <network> at device 2.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
pci0: <mass storage, ATA> at device 31.1 (no driver attached)
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
orm0: <Option ROMs> at iomem 0xe0000-0xeffff,0xdc000-0xdffff,0xd1000-0xd1fff,0xd0000-0xd0fff,0xc0000-0xcffff on isa0
pmtimer0 on isa0
ata0 at port 0x3f6,0x1f0-0x1f7 irq 14 on isa0
ata1 at port 0x376,0x170-0x177 irq 15 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
system power profile changed to 'economy'
ata1-slave: timeout waiting for interrupt
ata1-slave: ATAPI identify failed
ad0: 73490MB <IC25N080ATMR04-0> [149313/16/63] at ata0-master PIO4
acd0: CD-RW <UJDA745 DVD/CDRW> at ata1-master PIO4
    ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT0._STA] (Node 0xc6195e80), AE_ERROR
    ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT0._STA] (Node 0xc6195e80), AE_ERROR
    ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT1._STA] (Node 0xc6195d00), AE_ERROR
    ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT1._STA] (Node 0xc6195d00), AE_ERROR
    ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.BAT1._BIF] (Node 0xc6195ce0), AE_ERROR
Mounting root from ufs:/dev/ad0s2a
system power profile changed to 'performance'

-- 
Jon Lech Johansen
jon@member.fsf.org
nanocrew.net/blog/

Stat sua cuique dies, breve et inreparabile tempus
omnibus est vitae; sed famam extendere factis,
hoc virtutis opus.



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030502172207.A15705>