Skip site navigation (1)Skip section navigation (2)
Date:      Sun, 1 Mar 2009 02:34:08 -0600 (CST)
From:      Larry Rosenman <ler@lerctr.org>
To:        Alexander Motin <mav@FreeBSD.org>
Cc:        Sam Leffler <sam@freebsd.org>, FreeBSD-Current <freebsd-current@freebsd.org>
Subject:   Re: ata problems @ r189170
Message-ID:  <alpine.BSF.2.00.0903010231420.30034@thebighonker.lerctr.org>
In-Reply-To: <49A9ACF2.3090101@FreeBSD.org>
References:  <49A99EA7.4000202@errno.com> <49A9A09A.2070900@freebsd.org> <49A9AA83.1030300@freebsd.org> <49A9ACF2.3090101@FreeBSD.org>

next in thread | previous in thread | raw e-mail | index | archive | help
On Sat, 28 Feb 2009, Alexander Motin wrote:

> Sam Leffler wrote:
>> Sam Leffler wrote:
>>> Sam Leffler wrote:
>>>> HEAD @ r189170 fails to boot on a T41.  Two cd/dvd drivers are recognized 
>>>> (only 1 exists) and I get complaints of the form (and transcribed):
>>>> 
>>>> acd1: WARNING - ATAPI_IDENTIFY taskqueue timeout - completing request 
>>>> directory
>>>> 
>>>> (similarly for acd0) until there's a panic:
>>>> 
>>>> panic: mtx_lock() of destroy mutex @ .../../../kern_sema.c:79
>>>> 
>>>> (stack trace uninteresting).
>>>> 
>>> 
>>> boot -v shows:
>>> 
>>> acd0: setting PIO4 on CH4 chip
>>> acd0: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout - ...
>>> acd0: setting UDMA32 on ICH4 chip
>>> ata1: Identifying devices: 00030000
>>> ata: New devices: 00000000
>>> ata1: reinit done ..
>>> panic ...
>> reverting r189166 gets me a bootable kernel.
>
> Looks like while fixing small problems I have found bigger ones. Try please 
> this patch against HEAD, it reverts r189166, r189091 and partially r188903:
>
> http://people.freebsd.org/~mav/ata.rollback.patch
>
> If it works, I will stop for some time to cool down and search for better 
> solution.
With the 189195 version from csup, I get all sorts of timeouts from my
ATA drives in ahci mode.

Kernel from:
FreeBSD borg.lerctr.org 8.0-CURRENT FreeBSD 8.0-CURRENT #3: Mon Feb  9 10:21:36 CST 2009     root@borg.lerctr.org:/usr/obj/usr/src/sys/BORG  amd64

works, the current (as of this writing) sources do NOT. 
Ideas on what to get?

dmesg from the running kernel:

Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
 	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-CURRENT #3: Mon Feb  9 10:21:36 CST 2009
     root@borg.lerctr.org:/usr/obj/usr/src/sys/BORG
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU            5120  @ 1.86GHz (1862.02-MHz K8-class CPU)
   Origin = "GenuineIntel"  Id = 0x6f6  Stepping = 6
   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
   Features2=0x4e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA>
   AMD Features=0x20100800<SYSCALL,NX,LM>
   AMD Features2=0x1<LAHF>
   TSC: P-state invariant
   Cores per package: 2
usable memory = 4283305984 (4084 MB)
avail memory  = 4120276992 (3929 MB)
ACPI APIC Table: <PTLTD  	 APIC  >
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
  cpu0 (BSP): APIC ID:  0
  cpu1 (AP): APIC ID:  1
  cpu2 (AP): APIC ID:  6
  cpu3 (AP): APIC ID:  7
This module (opensolaris) contains code covered by the
Common Development and Distribution License (CDDL)
see http://opensolaris.org/os/licensing/opensolaris_license/
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
kbd1 at kbdmux0
smbios0: <System Management BIOS> at iomem 0xf60c0-0xf60de on motherboard
smbios0: Version: 2.5
cryptosoft0: <software crypto> on motherboard
acpi0: <SMCI SMCISLP2> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci1
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci2
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 0.0 on pci3
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 0.2 on pci3
pci5: <ACPI PCI bus> on pcib5
pcib6: <ACPI PCI-PCI bridge> irq 18 at device 2.0 on pci2
pci6: <ACPI PCI bus> on pcib6
em0: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x2000-0x201f mem 0xd8000000-0xd801ffff irq 18 at device 0.0 on pci6
em0: Using MSI interrupt
em0: [FILTER]
em0: Ethernet address: 00:30:48:8e:9f:f3
em1: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x2020-0x203f mem 0xd8020000-0xd803ffff irq 19 at device 0.1 on pci6
em1: Using MSI interrupt
em1: [FILTER]
em1: Ethernet address: 00:30:48:8e:9f:f2
pcib7: <ACPI PCI-PCI bridge> at device 0.3 on pci1
pci7: <ACPI PCI bus> on pcib7
pcib8: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pci8: <ACPI PCI bus> on pcib8
pcib9: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci9: <ACPI PCI bus> on pcib9
pci0: <base peripheral> at device 8.0 (no driver attached)
pcib10: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci10: <ACPI PCI bus> on pcib10
uhci0: <Intel 631XESB/632XESB/3100 USB controller USB-1> port 0x1800-0x181f irq 17 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <Intel 631XESB/632XESB/3100 USB controller USB-1> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 631XESB/632XESB/3100 USB controller USB-2> port 0x1820-0x183f irq 19 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <Intel 631XESB/632XESB/3100 USB controller USB-2> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 631XESB/632XESB/3100 USB controller USB-3> port 0x1840-0x185f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <Intel 631XESB/632XESB/3100 USB controller USB-3> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 63XXESB USB 2.0 controller> mem 0xd8500400-0xd85007ff irq 17 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 63XXESB USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
ums0: <Peppercon AG Multidevice, class 0/0, rev 2.00/0.01, addr 2> on uhub3
ums0: 3 buttons and Z dir.
ukbd0: <Peppercon AG Multidevice, class 0/0, rev 2.00/0.01, addr 2> on uhub3
kbd2 at ukbd0
pcib11: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci11: <ACPI PCI bus> on pcib11
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel 63XXESB2 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1860-0x186f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
atapci1: <Intel AHCI controller> port 0x18a0-0x18a7,0x1874-0x1877,0x1878-0x187f,0x1870-0x1873,0x1880-0x189f mem 0xd8500800-0xd8500bff irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
atapci1: AHCI Version 01.10 controller with 6 ports PM supported
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci1
ata5: [ITHREAD]
ata6: <ATA channel 4> on atapci1
ata6: [ITHREAD]
ata7: <ATA channel 5> on atapci1
ata7: [ITHREAD]
ichsmb0: <Intel 631xESB/6321ESB (ESB2) SMBus controller> port 0x1100-0x111f irq 19 at device 31.3 on pci0
ichsmb0: [ITHREAD]
smbus0: <System Management Bus> on ichsmb0
smb0: <SMBus generic I/O> on smbus0
acpi_button0: <Power Button> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppc0: [ITHREAD]
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
cpu0: <ACPI CPU> on acpi0
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
cpu2: <ACPI CPU> on acpi0
coretemp2: <CPU On-Die Thermal Sensors> on cpu2
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
cpu3: <ACPI CPU> on acpi0
coretemp3: <CPU On-Die Thermal Sensors> on cpu3
est3: <Enhanced SpeedStep Frequency Control> on cpu3
p4tcc3: <CPU Frequency Thermal Control> on cpu3
ipmi0: <IPMI System Interface> on isa0
ipmi0: KCS mode found at io 0xca2 alignment 0x1 on isa
orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
WARNING: ZFS is considered to be an experimental feature in FreeBSD.
Timecounters tick every 1.000 msec
ZFS filesystem version 13
ZFS storage pool version 13
acd0: DMA limited to UDMA33, controller found non-ATA66 cable
acd0: DVDR <Memorex DVD+-RAM 510L v1/MWS7> at ata0-master UDMA33
ad4: 381554MB <Seagate ST3400620AS 3.AAJ> at ata2-master SATA300
ad6: 381554MB <Seagate ST3400620AS 3.AAJ> at ata3-master SATA300
ad8: 476940MB <Seagate ST3500630AS 3.AAE> at ata4-master SATA300
ad10: 381554MB <Seagate ST3400620AS 3.AAJ> at ata5-master SATA300
ad12: 381554MB <Seagate ST3400620AS 3.AAJ> at ata6-master SATA300
ad14: 381554MB <Seagate ST3400620AS 3.AAJ> at ata7-master SATA300
ipmi0: IPMI device rev. 1, firmware rev. 1.2, version 2.0
ipmi0: Number of channels 8
ipmi0: Attached watchdog
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
GEOM: ad4s1: geometry does not match label (255h,63s != 16h,63s).
Trying to mount root from ufs:/dev/ad4s1a
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 
(probe0:ata0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:ata0:0:0:0): CAM Status: SCSI Status Error
(probe0:ata0:0:0:0): SCSI Status: Check Condition
(probe0:ata0:0:0:0): NOT READY asc:3a,0
(probe0:ata0:0:0:0): Medium not present
(probe0:ata0:0:0:0): Unretryable error
cd0 at ata0 bus 0 target 0 lun 0
cd0: <Memorex DVD+-RAM 510L v1 MWS7> Removable CD-ROM SCSI-0 device 
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
em0: link state changed to UP
>

-- 
Larry Rosenman                     http://www.lerctr.org/~ler
Phone: +1 512-248-2683                 E-Mail: ler@lerctr.org
US Mail: 430 Valona Loop, Round Rock, TX 78681-3893



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?alpine.BSF.2.00.0903010231420.30034>