Date: Sat, 24 Jan 2004 07:30:16 -0800 (PST) From: supraexpress@globaleyes.net To: freebsd-i386@FreeBSD.org Subject: Re: i386/60817: FBSD-5.1/5.2-RC1 "fdc0: cmd 3 failed at out byte 1 of 3" Message-ID: <200401241530.i0OFUGhx090969@freefall.freebsd.org>
next in thread | raw e-mail | index | archive | help
The following reply was made to PR i386/60817; it has been noted by GNATS.
From: supraexpress@globaleyes.net
To: freebsd-gnats-submit@FreeBSD.org
Cc: Dierk Sacher <usenet@blaxxtarz.de>
Subject: Re: i386/60817: FBSD-5.1/5.2-RC1 "fdc0: cmd 3 failed at out byte 1
of 3"
Date: Sat, 24 Jan 2004 09:24:01 -0600 (CST)
--0-1804289383-1074957848=:726
Content-Type: TEXT/plain; charset=us-ascii
Still unable to get my floppy disk to work under 5.2-RC2. Have tried the
following with no noticeable affect:
1) disable BIOS for MS6758 (875P Neo) setting for "APIC ACPI SCI IRQ",
the only BIOS setting specifically related to ACPI
BIOS is at latest version as of 12/2003
2) inserted two lines into /boot/loader.conf which did not display any
more boot information, so I obviously have these placed incorrectly
debug.acpi.layer="ACPI_HARDWARE ACPI_BUS"
debug.acpi.level="ACPI_LV_ALLOCATIONS ACPI_LV_INFO"
3) added the following line in /boot/device.hints to attempt to disable
runtime ACPI, which apparently did not work, or at least - had no
apparent affect with regards to FDC0:
hint.acpi.0.disable="1"
4) rebuilt and installed kernel withOUT "SMP" and "APIC" options
no change in FDC failure or APIC error messages
system hangs at mounting root device
5) sent e-mail to MSI and they suggested "disabling APIC and seeing if
the system would (continue) to boot", which as shown above, has no
affect on the problem
6) I have done a cursory examination of attempting to understand and
recompile the ADST (?), but do not have enough information nor
experience with such to be able to effectively do anything
Attached are the boot messages displayed for both FBSD-5.1-RC2 and
FBSD-4.9, using the same base system, but different SCSI harddrives. The
installed floppy drive works under FBSD-4.x.
The kernel that I use has only a few differences from the distributed
GENERIC, in both FBSD V4/V5 "systems":
only i686 is defined
kernel name is changed
all NFS options are commented out
IPFILTER options are added
--0-1804289383-1074957848=:726
Content-Type: TEXT/plain; name="dmesg.boot"
Content-Description: FBSD-5.1-RC2 boot dmesg
Content-Disposition: attachment; filename="dmesg.boot"
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2-RC2 #0: Sat Jan 24 08:33:26 CST 2004
root@freebsd2.localnet10:/usr/src/sys/i386/compile/5.2_RC2
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0c01000.
Preloaded elf module "/boot/kernel/linux.ko" at 0xc0c01244.
Preloaded elf module "/boot/kernel/snd_emu10k1.ko" at 0xc0c012f0.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0c013a0.
Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc0c0144c.
Preloaded elf module "/boot/kernel/nvidia.ko" at 0xc0c014f8.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0c015a4.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 3.20GHz (3245.47-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 1073676288 (1023 MB)
avail memory = 1029304320 (981 MB)
ACPI APIC Table: <AMIINT INTEL875>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <AMIINT INTEL875> on motherboard
acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 20
pcibios: BIOS version 2.10
Using $PIR table, 12 entries at 0xc00f7c30
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.MDET] (Node 0xc2dafac0), AE_AML_REGION_LIMIT
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0._CRS] (Node 0xc2daf9c0), AE_AML_REGION_LIMIT
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0._CRS] (Node 0xc2daf9c0), AE_AML_REGION_LIMIT
can't fetch resources for \\_SB_.PCI0 - AE_AML_REGION_LIMIT
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.MDET] (Node 0xc2dafac0), AE_AML_REGION_LIMIT
ACPI-1287: *** Error: Method execution failed [\\_SB_.MEM_._CRS] (Node 0xc2dc78a0), AE_AML_REGION_LIMIT
ACPI-0175: *** Error: Method execution failed [\\_SB_.MEM_._CRS] (Node 0xc2dc78a0), AE_AML_REGION_LIMIT
can't fetch resources for \\_SB_.MEM_ - AE_AML_REGION_LIMIT
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
acpi_cpu1: Failed to attach throttling P_CNT
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82875P host to AGP bridge> mem 0xfc000000-0xfdffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pcib1: slot 0 INTA is routed to irq 16
nvidia0: <GeForce4 Ti 4600> mem 0xf9a80000-0xf9afffff,0xf0000000-0xf7ffffff,0xfa000000-0xfaffffff irq 16 at device 0.0 on pci1
pci0: <base peripheral> at device 6.0 (no driver attached)
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xe000-0xe01f irq 16 at device 29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xe400-0xe41f irq 19 at device 29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xe800-0xe81f irq 18 at device 29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ugen0: APC Back-UPS ES 725 FW:802.n2.D USB FW:n2, rev 1.10/1.06, addr 2
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xec00-0xec1f irq 16 at device 29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcm0: <Creative EMU10K1> port 0xc400-0xc41f irq 17 at device 1.0 on pci2
pcm0: <SigmaTel STAC9708/11 AC97 Codec>
ahc0: <Adaptec 29160N Ultra160 SCSI adapter> port 0xc800-0xc8ff mem 0xfbeff000-0xfbefffff irq 18 at device 2.0 on pci2
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xc000-0xc0ff mem 0xfbefe000-0xfbefefff irq 19 at device 3.0 on pci2
sis0: Silicon Revision: DP83815D
sis0: Ethernet address: 00:09:5b:1e:62:ec
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: <Intel 82801BA (D865) Pro/100 VE Ethernet> port 0xbc00-0xbc3f mem 0xfbefd000-0xfbefdfff irq 20 at device 8.0 on pci2
fxp0: Ethernet address 00:0c:76:26:da:ea
miibus1: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> on miibus1
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 UDMA100 controller> port 0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcm1: <Intel ICH5 (82801EB)> port 0xd800-0xd83f,0xdc00-0xdcff mem 0xfbfff900-0xfbfff9ff,0xfbfffa00-0xfbfffbff irq 17 at device 31.5 on pci0
pcm1: <Analog Devices AD1980 AC97 Codec>
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
fdc0: cmd 3 failed at out byte 1 of 3
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
fdc0: cmd 3 failed at out byte 1 of 3
orm0: <Option ROMs> at iomem 0xe0000-0xe0fff,0xc0000-0xce7ff on isa0
pmtimer0 on isa0
fdc0: cannot reserve I/O port range (6 ports)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
IP Filter: v3.4.31 initialized. Default = pass all, Logging = enabled
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
acd0: CDRW <SAMSUNG CDRW/DVD SM-348B> at ata0-master PIO4
GEOM: create disk ad2 dp=0xc6f8fe60
ad2: 38196MB <SAMSUNG SV4002H> [77605/16/63] at ata1-master UDMA100
Waiting 15 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 2 lun 0
sa0: <ECRIX VXA-1 2C8C> Removable Sequential Access SCSI-2 device
sa0: 80.000MB/s transfers (40.000MHz, offset 32, 16bit)
GEOM: create disk da0 dp=0xc6f96c50
GEOM: create disk da1 dp=0xc6f98c50
GEOM: create disk da2 dp=0xc6df3c50
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST336752LW 0004> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 35003MB (71687369 512 byte sectors: 255H 63S/T 4462C)
da1 at ahc0 bus 0 target 4 lun 0
da1: <SEAGATE ST34501N 0015> Fixed Direct Access SCSI-2 device
da1: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
da1: 4339MB (8887200 512 byte sectors: 255H 63S/T 553C)
da2 at ahc0 bus 0 target 6 lun 0
da2: < S7Z0> Fixed Direct Access SCSI-3 device
da2: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da2: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/da1s1a
--0-1804289383-1074957848=:726
Content-Type: TEXT/plain; name="dmesg.boot"
Content-Description: FBSD-4.9 boot dmesg
Content-Disposition: attachment; filename="dmesg.boot"
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.9-RELEASE #0: Mon Jan 19 13:47:35 CST 2004
jimd@FreeBSD2.LocalNET10:/usr/src/sys/compile/XSYSTEM
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel(R) Pentium(R) 4 CPU 3.20GHz (3245.47-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 1073676288 (1048512K bytes)
avail memory = 1037750272 (1013428K bytes)
Preloaded elf kernel "kernel" at 0xc071a000.
Preloaded elf module "linux.ko" at 0xc071a09c.
Preloaded elf module "nvidia.ko" at 0xc071a13c.
Preloaded elf module "snd_pcm.ko" at 0xc071a1dc.
Preloaded elf module "snd_ich.ko" at 0xc071a27c.
Preloaded elf module "snd_emu10k1.ko" at 0xc071a31c.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 12 entries at 0xc00f7c30
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82875P host to AGP bridge> mem 0xfc000000-0xfdffffff at device 0.0 on pci0
pcib1: <PCI to PCI bridge (vendor=8086 device=2579)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
nvidia0: <GeForce4 Ti 4600> mem 0xf9a80000-0xf9afffff,0xf0000000-0xf7ffffff,0xfa000000-0xfaffffff irq 11 at device 0.0 on pci1
pci0: <unknown card> (vendor=0x8086, dev=0x257e) at 6.0
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xe000-0xe01f irq 11 at device 29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xe400-0xe41f irq 5 at device 29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xe800-0xe81f irq 10 at device 29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhid0: APC Back-UPS ES 725 FW:802.n2.D USB FW:n2, rev 1.10/1.06, addr 2, iclass 3/0
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xec00-0xec1f irq 11 at device 29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <USB controller> at 29.7 irq 5
pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
pcm0: <Creative EMU10K1> port 0xc400-0xc41f irq 11 at device 1.0 on pci2
pcm0: <SigmaTel STAC9708/11 AC97 Codec>
ahc0: <Adaptec 29160N Ultra160 SCSI adapter> port 0xc800-0xc8ff mem 0xfbeff000-0xfbefffff irq 10 at device 2.0 on pci2
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
sis0: <NatSemi DP83815 10/100BaseTX> port 0xc000-0xc0ff mem 0xfbefe000-0xfbefefff irq 5 at device 3.0 on pci2
sis0: Ethernet address: 00:09:5b:1e:62:ec
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: <Intel 82801BA (D865) Pro/100 VE Ethernet> port 0xbc00-0xbc3f mem 0xfbefd000-0xfbefdfff irq 11 at device 8.0 on pci2
fxp0: Ethernet address 00:0c:76:26:da:ea
inphy0: <i82562ET 10/100 media interface> on miibus1
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=24d0)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 ATA100 controller> port 0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x24d3) at 31.3 irq 11
pcm1: <Intel ICH5 (82801EB)> port 0xd800-0xd83f,0xdc00-0xdcff mem 0xfbfff900-0xfbfff9ff,0xfbfffa00-0xfbfffbff irq 11 at device 31.5 on pci0
pcm1: <Analog Devices AD1980 AC97 Codec>
orm0: <Option ROMs> at iomem 0xc0000-0xce7ff,0xe0000-0xe0fff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
IP Filter: v3.4.31 initialized. Default = pass all, Logging = enabled
ad2: 38196MB <SAMSUNG SV4002H> [77605/16/63] at ata1-master UDMA100
acd0: CD-RW <SAMSUNG CDRW/DVD SM-348B> at ata0-master PIO4
Waiting 5 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 2 lun 0
sa0: <ECRIX VXA-1 2C8C> Removable Sequential Access SCSI-2 device
sa0: 80.000MB/s transfers (40.000MHz, offset 32, 16bit)
Mounting root from ufs:/dev/da0s1a
da2 at ahc0 bus 0 target 6 lun 0
da2: < S7Z0> Fixed Direct Access SCSI-3 device
da2: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da2: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
da1 at ahc0 bus 0 target 4 lun 0
da1: <SEAGATE ST34501N 0015> Fixed Direct Access SCSI-2 device
da1: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
da1: 4339MB (8887200 512 byte sectors: 255H 63S/T 553C)
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST336752LW 0004> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 35003MB (71687369 512 byte sectors: 255H 63S/T 4462C)
--0-1804289383-1074957848=:726--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200401241530.i0OFUGhx090969>