Date: Wed, 31 Dec 2003 13:58:54 -0700 From: "axiom" <axiom@VectorNS.com> To: doc@freebsd.org Subject: VPN over IPsec Message-ID: <20031231205854.3560.qmail@vectorns.com>
next in thread | raw e-mail | index | archive | help
This is a MIME-formatted message. If you see this text it means that your
mail software cannot handle MIME-formatted messages.
--=_0_3559_1072904334
Content-Type: text/plain; format=flowed; charset=utf-8
Content-Transfer-Encoding: 7bit
I have a question regarding the document that talks about "VPN over IPsec".
I'm trying to create the interface gif0 at boot time and am adding the
following to my /etc/rc.conf according to your document:
gifconfig_gif0="A.B.C.D W.X.Y.Z"
ifconfig_gif0="inet 192.168.1.1 192.168.2.1 netmask 0xffffffff"
static_routes="vpn"
route_vpn="192.168.2.0 192.168.2.1 netmask 0xffffff00"
I've obviously changed the IP address schemes to fit my network.
Using this same documentation on "VPN over IPsec" I can setup the gif0
interface manually with no problems and everything works. I just don't want
to have to set it up manually every time I reboot.
Any suggestions on why the setup to /etc/rc.conf from your documentation
doesn't work?
******************************************************************
One other thing i'd like to point out on that document is that when you tell
the user to run "gifconfig gif0 A.B.C.D W.X.Y.Z" it doesn't work. You must
first create gif0 with "ifconfig gif0 create" and then continue with your
documentation.
Thanks much,
-Casey
P.S. Attached is the output from dmesg!
--=_0_3559_1072904334
Content-Disposition: attachment; filename=dmesg.txt
Content-Type: text/plain; charset="utf-8"; name=dmesg.txt
Content-Transfer-Encoding: 7bit
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.1-RELEASE #0: Sun Dec 28 18:57:35 MST 2003
axiom@Lewis-Router.vectorns.com:/usr/src/sys/i386/compile/LEWIS_KERN
Preloaded elf kernel "/boot/kernel/kernel" at 0xc06da000.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 166587302 Hz
CPU: Pentium/P55C (166.59-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x543 Stepping = 3
Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
real memory = 67108864 (64 MB)
avail memory = 57843712 (55 MB)
Intel Pentium detected, installing workaround for F00F bug
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcibios: BIOS version 2.10
pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 WDMA2 controller> port 0xffa0-0xffaf at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <display, VGA> at device 8.0 (no driver attached)
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x7880-0x78ff mem 0xffaefb80-0xffaefbff irq 9 at device 9.0 on pci0
xl0: Ethernet address: 00:50:04:73:5e:97
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc0: <ADMtek AN985 10/100BaseTX> port 0x7c00-0x7cff mem 0xffaefc00-0xffaeffff irq 10 at device 10.0 on pci0
dc0: Ethernet address: 00:04:5a:72:f8:cf
miibus1: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
eisa0: <EISA bus> on motherboard
eisa0: unknown card DF@0020 (0x10c00020) at slot 7
orm0: <Option ROMs> at iomem 0xf4000-0xf4fff,0xc0000-0xc7fff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0400> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (port)
Timecounters tick every 10.000 msec
BRIDGE 020214 loaded
DUMMYNET initialized (011031)
ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to accept, logging limited to 100 packets/entry by default
IPsec: Initialized Security Association Processing.
ad0: 14598MB <SAMSUNG SV1533D> [29660/16/63] at ata0-master WDMA2
Mounting root from ufs:/dev/ad0s1a
arp: 24.117.26.1 moved from 00:08:20:cb:08:8c to 00:08:20:cb:08:54 on dc0
arplookup 192.168.1.30 failed: host is not on local network
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: host is not on local network
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: host is not on local network
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: host is not on local network
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: host is not on local network
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: host is not on local network
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: could not allocate llinfo
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: could not allocate llinfo
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: could not allocate llinfo
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: could not allocate llinfo
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: could not allocate llinfo
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: could not allocate llinfo
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: could not allocate llinfo
arpresolve: can't allocate llinfo for 192.168.1.30rt
arplookup 192.168.1.30 failed: could not allocate llinfo
arpresolve: can't allocate llinfo for 192.168.1.30rt
--=_0_3559_1072904334--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20031231205854.3560.qmail>