Date: Sun, 12 Aug 2001 01:11:53 -0700 From: Kent Stewart <kstewart@urx.com> To: Lasse Kaislaniemi <lasse@mutteri.org> Cc: freebsd-questions@FreeBSD.org Subject: Re: USB mouse not working under 4.3-REL Message-ID: <3B763A49.BA100DB7@urx.com> References: <Pine.NEB.4.33.0108120944510.27743-100000@ns1.mutteri.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Lasse Kaislaniemi wrote: > > Hi, > > I'd like to get my USB mouse to work in my FreeBSD box. There is a support > for USB mice in the GENERAL kernel, however that didn't work so I compiled > a customized kernel with lines > > pseudo-device ether > device uhci > #device ohci # I've tried with this one enabled too > device usb > device ums > > options UHCI_DEBUG > options USB_DEBUG > options UMS_DEBUG My usb mouse works and what I have for a kernel config is # USB support device uhci # UHCI PCI->USB interface device ohci # OHCI PCI->USB interface device usb # USB Bus (required) device ugen # Generic device uhid # "Human Interface Devices" device ukbd # Keyboard #device ulpt # Printer #device umass # Disks/Mass storage - Requires scbus and da device ums # Mouse # USB Ethernet, requires mii #device aue # ADMtek USB ethernet #device cue # CATC USB ethernet #device kue # Kawasaki LSI USB ethernet I have moused_enable turned off in /etc/rc.conf and usb_enable="YES". Kent > > in it, and any other USB related stuff commented out. But after compiling > the kernel I still keep on getting this stuff in dmesg: > > ... > pcib0: <Host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pcib1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > isab0: <VIA 82C586 PCI-ISA bridge> at device 7.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <VIA 82C586 ATA33 controller> port 0xe000-0xe00f at device 7.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > uhci0: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 12 at device 7.2 on pci0 > uhci_run: setting run=0 > uhci_run: done cmd=0x0 sts=0x20 > uhci_run: setting run=1 > uhci_run: done cmd=0x81 sts=0x0 > usb0: <VIA 83C572 USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhci_waitintr: timeout > uhci_idone: error, addr=2, endpt=0x00, status 0x500000<BABBLE,STALLED> > uhci_waitintr: timeout > usbd_transfer_cb: short transfer 0<1 > uhci_waitintr: timeout > usbd_transfer_cb: short transfer 0<1 > ums0: Logitech, Inc. product 0xc030, rev 1.00/1.01, addr 2, iclass 3/1 > uhci_waitintr: timeout > usbd_transfer_cb: short transfer 0<74 > device_probe_and_attach: ums0 attach returned 6 > uhci_waitintr: timeout > usbd_transfer_cb: short transfer 0<1 > uhci_waitintr: timeout > usbd_transfer_cb: short transfer 0<1 > chip1: <VIA 82C586B ACPI interface> at device 7.3 on pci0 > ... > > Now, '# moused -p /dev/ums0 -t auto' says 'Device not confgured'. > MAKEDEVing doesn't help. > > If I deattach the mouse from the USB port before booting, I won't get > those error messages at boot time, but still I get the errors when > attaching the mouse to the USB port after boot process. > > Can anyone help or should I just go and buy a good old serial mouse?-) > > Thanks in advance, > > -- > Lasse Kaislaniemi / lasse@mutteri.org > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-questions" in the body of the message -- Kent Stewart Richland, WA mailto:kbstew99@hotmail.com http://kstewart.urx.com/kstewart/index.html FreeBSD News http://daily.daemonnews.org/ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3B763A49.BA100DB7>