Date: Thu, 1 Nov 2001 22:23:11 +0200 (EET) From: Lasse Kaislaniemi <lasse@mutteri.org> To: <questions@FreeBSD.org> Subject: USB mouse not working in 4.4-REL Message-ID: <Pine.NEB.4.33.0111012220080.23370-100000@ns1.mutteri.org>
next in thread | raw e-mail | index | archive | help
Hi,
I'm having a little trouble with my USB mouse in my FreeBSD 4.4-REL.
I've compiled a kernel of my own with USB devices uhci, ohci, usb and
ums (also debug options are enabled). But in dmesg I still get the messages
shown below. My mouse is Logitech iFeel USB mouse.
The mouse did work in Win2k and all the devices there had the same
irq's than now.
After the boot I can get this from usbdevs:
# usbdevs -v
Controller /dev/usb0:
addr 1: self powered, config 1, UHCI root hub(0x0000), VIA(0x0000), rev 0x0100
port 1 powered
port 2 addr 2: low speed, power 500 mA, config 1, product 0xc030(0xc030), Logitech, Inc.(0x046d), rev 0x0101
However, 'moused -p /dev/ums0 -t auto' still says 'Device not configured'.
I'd be very delighted if someone had a piece of advice to give
how to get this thing work -- X isn't very useable without mouse... <g>.
--
Lasse Kaislaniemi / lasse@mutteri.org
--
# dmesg
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.4-RELEASE #17: Sun Oct 28 18:26:59 EET 2001
root@toosa.mutteri.org:/usr/src/sys/compile/TOOSA
Timecounter "i8254" frequency 1193182 Hz
CPU: AMD-K6(tm) 3D processor (334.40-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x58c Stepping = 12
Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX>
AMD Features=0x80000800<SYSCALL,3DNow!>
real memory = 201326592 (196608K bytes)
avail memory = 192352256 (187844K bytes)
Preloaded elf kernel "kernel" at 0xc0380000.
K6-family MTRR support enabled (2 registers)
md0: Malloc disk
Using $PIR table, 4 entries at 0xc00fde80
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <VIA 82C586 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C586 ATA33 controller> port 0xe000-0xe00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 10 at device 7.2 on pci0
uhci_run: setting run=0
uhci_run: done cmd=0x0 sts=0x20
uhci_run: setting run=1
uhci_run: done cmd=0x81 sts=0x0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci_waitintr: timeout
uhci_idone: error, addr=2, endpt=0x00, status 0x500000<BABBLE,STALLED>
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<1
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<1
ums0: Logitech, Inc. product 0xc030, rev 1.00/1.01, addr 2, iclass 3/1
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<74
device_probe_and_attach: ums0 attach returned 6
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<1
uhci_waitintr: timeout
usbd_transfer_cb: short transfer 0<1
chip1: <VIA 82C586B ACPI interface> at device 7.3 on pci0
pci0: <3Dfx Voodoo 3 graphics accelerator> at 8.0 irq 5
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
ep0: <3Com 3C509-Combo EtherLink III> at port 0x210-0x21f irq 11 on isa0
ep0: Ethernet address 00:20:af:10:e8:b3
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sbc0: <SoundBlaster 16> at port 0x220-0x22f irq 9 drq 1 flags 0xe on isa0
pcm0: <SB16 DSP 4.13> on sbc0
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
ad0: 32253MB <SAMSUNG SV4084H> [65531/16/63] at ata0-master UDMA33
acd0: CDROM <IDE/ATAPI CD-ROM 44XS> at ata1-master using PIO4
Mounting root from ufs:/dev/ad0s2a
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.NEB.4.33.0111012220080.23370-100000>