Date: Fri, 3 Mar 2000 13:29:00 -0500 From: "Mike Donnelly" <freebsd@rockatronic.com> To: <freebsd-questions@freebsd.org> Subject: Adaptec 2930CU / AIC7859 failure Message-ID: <00d601bf853e$58c2ef20$3517390a@localdomain>
next in thread | raw e-mail | index | archive | help
Hello all,
I've had no success getting a recent vintage North American market Adaptec
2930CU to work. I've CVSuped and tried both the v.3 stable and 4 current
source trees. Nothing works. Just times out on probe (dmesg below). The
card works fine with Redhat Linux 6.1 and Windows 98. Its not a cabling or
term. problem as the other OSes work and the errors remain identical whether
there is an external cable and/or device attached or not. There is no
internal device. I've tried manual term. as well.
I called Adaptec to confirm the controller chip; they say AIC7859 BT. Read
the sources, seems to jibe OK, as in AIC7859. Note, on probe Linux loads
the AIC7860 not 7859. I tried substituting the 7850, 7855,7860 and 7870 by
modifiying the features line in the setup routine for 2930CU in aic7xxx.h.
Recompile, test. etc. etc. No success. Also tried all reasonable
permutations on Adaptec SCSI setup (ctrl-a) just for "fun". No success.
Any insight would be greatly appreciated.
Thanks
Mike
Copyright (c) 1992-1999 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.4-STABLE #0: Fri Mar 3 08:54:33 EST 2000
root@stang.localdomain:/usr/src/sys/compile/STANG
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium/P55C (232.96-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x543 Stepping = 3
Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
real memory = 67108864 (65536K bytes)
avail memory = 61747200 (60300K bytes)
Preloaded elf kernel "kernel" at 0xc035c000.
Probing for devices on PCI bus 0:
chip0: <Intel 82439TX System Controller (MTXC)> rev 0x01 on pci0.0.0
chip1: <Intel 82371AB PCI to ISA bridge> rev 0x01 on pci0.7.0
ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1
chip2: <Intel 82371AB Power management controller> rev 0x01 on pci0.7.3
vga0: <3Dfx Voodoo 3 graphics accelerator> rev 0x01 int a irq 0 on pci0.8.0
vr0: <VIA VT3043 Rhine I 10/100BaseTX> rev 0x06 int a irq 10 on pci0.10.0
vr0: Ethernet address: 00:50:ba:c2:a1:73
vr0: autoneg complete, link status good (half-duplex, 100Mbps)
ahc0: <Adaptec 2930CU SCSI adapter> rev 0x03 int a irq 11 on pci0.11.0
ahc0: aic7859 Single Channel A, SCSI Id=7, 3/255 SCBs
Probing for PnP devices:
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
ed0 not found at 0x280
fe0 not found at 0x300
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
psm0 irq 12 on isa
psm0: model IntelliMouse, device ID 3
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <Maxtor 85120 A8 ->
wd0: 4884MB (10003392 sectors), 9924 cyls, 16 heads, 63 S/T, 512 B/S
wdc1 at 0x170-0x177 irq 15 on isa
wdc1: unit 0 (atapi): <ATAPI CD ROM DRIVE 50X MAX/VER 50JT>, removable,
accel, dma, iordy
acd0: drive speed 171 - 8593KB/sec, 128KB cache
acd0: supported read types: CD-R, CD-RW, CD-DA, packet track
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
wt0 not found at 0x300
mcd0 not found at 0x300
matcdc0 not found at 0x230
scd0 not found at 0x230
ppc0 at 0x378 irq 7 flags 0x40 on isa
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
plip0: <PLIP network interface> on ppbus 0
ie0: unknown board_id: f000
ie0 not found at 0x300
ep0 not found at 0x300
ex0 not found
le0 not found at 0x300
lnc0 not found at 0x280
cs0 not found at 0x300
ze0 not found at 0x300
zp0 not found at 0x300
adv0 not found at 0x330
bt0 not found at 0x134
aha0 not found at 0x134
aic0 not found
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
Intel Pentium detected, installing workaround for F00F bug
Waiting 8 seconds for SCSI devices to settle
(probe1:ahc0:0:1:0): SCB 0xd - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe1:ahc0:0:1:0): Queuing a BDR SCB
(probe1:ahc0:0:1:0): SCB 0xd - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe1:ahc0:0:1:0): no longer in timeout, status = 34b
ahc0: Issued Channel A Bus Reset. 6 SCBs aborted
(probe2:ahc0:0:2:0): SCB 0xd - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe2:ahc0:0:2:0): Queuing a BDR SCB
(probe2:ahc0:0:2:0): SCB 0xd - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe2:ahc0:0:2:0): no longer in timeout, status = 34b
ahc0: Issued Channel A Bus Reset. 6 SCBs aborted
(probe3:ahc0:0:3:0): SCB 0xd - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe3:ahc0:0:3:0): Queuing a BDR SCB
(probe3:ahc0:0:3:0): SCB 0xd - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe3:ahc0:0:3:0): no longer in timeout, status = 34b
ahc0: Issued Channel A Bus Reset. 6 SCBs aborted
(probe5:ahc0:0:5:0): SCB 0x8 - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe5:ahc0:0:5:0): Queuing a BDR SCB
(probe5:ahc0:0:5:0): SCB 0x8 - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe5:ahc0:0:5:0): no longer in timeout, status = 34b
ahc0: Issued Channel A Bus Reset. 5 SCBs aborted
(probe1:ahc0:0:1:0): SCB 0xc - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe1:ahc0:0:1:0): Queuing a BDR SCB
(probe1:ahc0:0:1:0): SCB 0xc - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe1:ahc0:0:1:0): no longer in timeout, status = 34b
ahc0: Issued Channel A Bus Reset. 4 SCBs aborted
(probe3:ahc0:0:3:0): SCB 0x9 - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe3:ahc0:0:3:0): Queuing a BDR SCB
(probe3:ahc0:0:3:0): SCB 0x9 - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe3:ahc0:0:3:0): no longer in timeout, status = 34b
ahc0: Issued Channel A Bus Reset. 3 SCBs aborted
(probe1:ahc0:0:1:0): SCB 0xb - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe1:ahc0:0:1:0): Queuing a BDR SCB
(probe1:ahc0:0:1:0): SCB 0xb - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe1:ahc0:0:1:0): no longer in timeout, status = 34b
ahc0: Issued Channel A Bus Reset. 2 SCBs aborted
(probe3:ahc0:0:3:0): SCB 0xb - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe3:ahc0:0:3:0): Queuing a BDR SCB
(probe3:ahc0:0:3:0): SCB 0xb - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe3:ahc0:0:3:0): no longer in timeout, status = 34b
ahc0: Issued Channel A Bus Reset. 2 SCBs aborted
(probe1:ahc0:0:1:0): SCB 0xb - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe1:ahc0:0:1:0): Queuing a BDR SCB
(probe1:ahc0:0:1:0): SCB 0xb - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe1:ahc0:0:1:0): no longer in timeout, status = 34b
ahc0: Issued Channel A Bus Reset. 2 SCBs aborted
(probe1:ahc0:0:1:0): SCB 0xa - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe1:ahc0:0:1:0): Queuing a BDR SCB
(probe1:ahc0:0:1:0): SCB 0xa - timed out while idle, LASTPHASE == 0x1,
SEQADDR == 0x188
(probe1:ahc0:0:1:0): no longer in timeout, status = 34b
ahc0: Issued Channel A Bus Reset. 1 SCBs aborted
changing root device to wd0s2a
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?00d601bf853e$58c2ef20$3517390a>