Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 25 May 2000 10:29:57 +0100
From:      David Harmelin <david.harmelin@dante.org.uk>
To:        itojun@iijlab.net
Cc:        freebsd-net@freebsd.org
Subject:   Re: nd6_lookup: failed to add route for neighbor
Message-ID:  <4.2.2.20000525102612.00b1ea30@alpha.dante.org.uk>
In-Reply-To: <1841.959190158@coconut.itojun.org>
References:  <david.harmelin's message of Wed, 24 May 2000 17:16:42 %2B0100. <4.2.2.20000524170030.00b0f100@alpha.dante.org.uk>

next in thread | previous in thread | raw e-mail | index | archive | help
The diagram is correct.

If I configure 3ffe:8038:80:3::3 to gif0, how is the mapping between that 
address and fxp1 done? (there are more than one network card)

I tried it, but the following routing entry is not there anymore:
3ffe:8038:80:3::3                 0:d0:b7:20:8a:7b              UHLW        lo0
which maps the ipv6 address to the mac address.

Best regards,

DH.

At 02:42 AM 5/25/00 +0900, itojun@iijlab.net wrote:

> >I'll try to make it as brief as possible.
> >I have a Freebsd 4.0 connected through a v6-on-v4 tunnel to a remote
> >router. The gif0 tunnel works fine (can ping the other v6 end).
> >My local v6 address is 3ffe:8038:80:3::3, configured on the fxp1 (ethernet)
> >interface, the other end is 3ffe:8038:80:3::2 .
>
>         is the following diagram correct?  if so, do not configure
>         3ffe:8038:80:3::3 onto fxp1.  configure the address to gif0, not 
> fxp1.
>         you are not supposed to use 3ffe:8038:80:3::/64 on fxp1.
>
>         the other end of tunnel
>           | 3ffe:8038:80:3::2
>           |
>           | tunnel link
>           |
>           |gif0 3ffe:8038:80:3::3
>         my end of tunnel
>           |fxp1
>         ==+=== ethernet
>
> >There is no autoconfiguration so I edited /etc/rc.conf so that
> >/etc/rc.network6 adds the local address it gets from there.
> >When I originally booted the station, netstat -rn output was:
> >3ffe:8038:80:3::/64               link#2             UGSc       fxp1
> >What adds this line? could not find it in rc.network6
>
>         ifconfig to fxp1.
>
> >My second question is: what link#2 stands for?
>
>         fxp1.
>
>itojun

___________________________________________________________________
             * *         David Harmelin  	Network Engineer
           *     *				DANCERT Representative
          *              Francis House
         *               112 Hills Road       Tel +44 1223 302992
         *               Cambridge CB2 1PQ    Fax +44 1223 303005
      D  A  N  T  E      United Kingdom       WWW http://www.dante.net
____________________________________________________________________



To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-net" in the body of the message




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4.2.2.20000525102612.00b1ea30>