Date: Mon, 28 Mar 2005 13:35:10 -0500 (EST) From: c0ldbyte <c0ldbyte@myrealbox.com> To: freebsd-net@freebsd.org Subject: Re: HOWTO connect MCI using Netgraph + Frame Relay with Digi SYNC/570i Message-ID: <20050328133403.E440@eleanor.us1.wmi.uvac.net> In-Reply-To: <424835C0.9070603@attglobal.net> References: <42344AF7.6070701@attglobal.net> <423C72A1.7060000@cronyx.ru> <4240497D.5030304@attglobal.net> <42404B15.5040605@elischer.org> <424835C0.9070603@attglobal.net>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, 29 Mar 2005, John Mok wrote: > > After issuing the following commands :- > > #ngctl mkpeer sync_ar0: frame_relay rawdata downstream > #ngctl mkpeer sync_ar0:rawdata lmi dlci0 ansi > #ngctl mkpeer sync_ar0:rawdata rfc1490 dlci16 rfc1490 > #ngctl mkpeer sync_ar0:rawdata dlci16 rl0 inet inet > #ifconfig ng0 1.2.3.4 5.6.7.8 > ifconfig: interface ng0 does not exist > > The command ifconfig shows :- > > rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > options=8<VLAN_MTU> > inet6 fe80::207:40ff:fe09:f09%rl0 prefixlen 64 scopeid 0x1 > inet 192.168.255.254 netmask 0xffffff00 broadcast 192.168.255.255 > ether 00:07:40:09:0f:09 > media: Ethernet autoselect (none) > status: no carrier > xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > options=9<RXCSUM,VLAN_MTU> > inet6 fe80::201:3ff:fec1:9c58%xl0 prefixlen 64 scopeid 0x2 > ether 00:01:03:c1:9c:58 > media: Ethernet autoselect (100baseTX <full-duplex>) > status: active > xl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > options=9<RXCSUM,VLAN_MTU> > inet6 fe80::201:3ff:fe34:61af%xl1 prefixlen 64 scopeid 0x3 > inet 192.168.16.254 netmask 0xffffff00 broadcast 192.168.16.255 > ether 00:01:03:34:61:af > media: Ethernet autoselect (100baseTX <full-duplex>) > status: active > plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500 > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 > inet6 ::1 prefixlen 128 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 > inet 127.0.0.1 netmask 0xff000000 > > and the command "ngctl list" shows :- > > There are 4 total nodes: > Name: ngctl811 Type: socket ID: 00000011 Num hooks: 0 > Name: <unnamed> Type: frame_relay ID: 00000004 Num hooks: 1 > Name: sync_ar1 Type: sync_ar ID: 00000002 Num hooks: 0 > Name: sync_ar0 Type: sync_ar ID: 00000001 Num hooks: 1 > > Would it be the problem that I test it with cable disconnected from the modem > (i.e.CSU/DSU)? > > Thanks a lot. > > John Mok > > > Julian Elischer wrote: > >> did the last command do anything? >> >> please show the output of: >> ifconfig >> ngctl list >> You have ng_ether or ng_iface loaded ?
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20050328133403.E440>