Date: Mon, 29 Sep 2003 19:08:25 +0200 From: Pierre Beyssac <pb@fasterix.frmug.org> To: freebsd-current@freebsd.org Subject: ATAng: DMA timeout, ICRC errors, ... Message-ID: <20030929170823.GA14806@fasterix.frmug.org>
next in thread | raw e-mail | index | archive | help
--envbJBWh7q8WU6mo
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
I've discovered several problems on my system with the ATAng driver.
Most of these seem related to one particular disk drive, but the
disk used to work fine with the older driver, so I assume the fault
lies with the new driver.
1) under heavy I/O, frequent occurences of "ad0: TIMEOUT - WRITE_DMA retrying".
Sometimes READ_DMA instead.
The IDE configuration:
ata0 -> 80-pin cable, one ATA100 capable 180Gb hard disk drive
ata1 -> 40-pin cable, a DVD reader and a DVD burner.
See dmesg.1, attached. This is the configuration where I get "TIMEOUT
- WRITE_DMA" on ad0.
2) I tried to add another (older) IDE drive which I put in the
following (non optimal) configuration:
ata0 -> 80-pin cable, 180Gb hard disk, DVD burner
ata1 -> 40-pin cable, 80Gb hard disk, DVD reader
The driver correctly disables the ATA66 mode on ata0, given that
the DVD burner is not ATA66-compliant. But no such message on ata1,
and I get many ICRC errors when accessing ad1, making ad1 totally
unusable.
See dmesg.2 attached.
3) both disk drives on ata0, both DVD drives on ata1:
ad0 (identified as ATA-6) is usable but thrashes on heavy I/O (DMA
problems when reading a DV file with fwcontrol(8)). Same problem
as 1) above, except the messages I get about timeouts are related
to firewire -- but I'm quite certain the problem is not firewire-related
as reading from firewire works perfectly fine when the file is
stored on the other drive.
Under heavy disk access (without firewire involved) I also get
bunches of:
ad0: WARNING - READ_DMA UDMA ICRC error (retrying request)
ad0: WARNING - READ_DMA UDMA ICRC error (retrying request)
ad0: WARNING - READ_DMA UDMA ICRC error (retrying request)
ad0: WARNING - READ_DMA UDMA ICRC error (retrying request)
Reading from/writing to ad1 (identified as ATA-5) exhibits no
problem.
See dmesg.3 attached.
--
Pierre Beyssac pb@fasterix.frmug.org pb@fasterix.freenix.org
Free domains: http://www.eu.org/ or mail dns-manager@EU.org
--envbJBWh7q8WU6mo
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.1"
e 0.8.3
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.0
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.1
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.2
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.3
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.3
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.3
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base e8000000, size 26, enabled
found-> vendor=0x1106, dev=0x0305, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x08 (240 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x8305, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x2230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x0686, revid=0x40
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000d000, size 4, enabled
found-> vendor=0x1106, dev=0x0571, revid=0x06
bus=0, slot=7, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000d400, size 5, enabled
pcib0: matched entry for 0.7.INTD (source \\_SB_.PCI0.LNKD)
pcib0: slot 7 INTD is routed to irq 5
found-> vendor=0x1106, dev=0x3038, revid=0x16
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=5
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000d800, size 5, enabled
pcib0: matched entry for 0.7.INTD (source \\_SB_.PCI0.LNKD)
pcib0: slot 7 INTD is routed to irq 5
found-> vendor=0x1106, dev=0x3038, revid=0x16
bus=0, slot=7, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=5
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x3057, revid=0x40
bus=0, slot=7, func=4
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000dc00, size 5, enabled
pcib0: matched entry for 0.8.INTA (source \\_SB_.PCI0.LNKD)
pcib0: slot 8 INTA is routed to irq 5
found-> vendor=0x1102, dev=0x0002, revid=0x08
bus=0, slot=8, func=0
class=04-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x14 (5000 ns)
intpin=a, irq=5
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e000, size 3, enabled
found-> vendor=0x1102, dev=0x7002, revid=0x08
bus=0, slot=8, func=1
class=09-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e400, size 8, enabled
map[14]: type 1, range 32, base ef003000, size 8, enabled
pcib0: matched entry for 0.9.INTA (source \\_SB_.PCI0.LNKC)
pcib0: slot 9 INTA is routed to irq 12
found-> vendor=0x1186, dev=0x1300, revid=0x10
bus=0, slot=9, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=12
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ef000000, size 12, enabled
pcib0: matched entry for 0.11.INTA (source \\_SB_.PCI0.LNKD)
pcib0: slot 11 INTA is routed to irq 5
found-> vendor=0x11c1, dev=0x5811, revid=0x04
bus=0, slot=11, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x0c (3000 ns), maxlat=0x18 (6000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e800, size 5, enabled
pcib0: matched entry for 0.13.INTA (source \\_SB_.PCI0.LNKB)
pcib0: slot 13 INTA is routed to irq 10
found-> vendor=0x10ec, dev=0x8029, revid=0x00
bus=0, slot=13, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
map[10]: type 4, range 32, base 0000ec00, size 8, enabled
map[14]: type 1, range 32, base ef001000, size 8, enabled
map[18]: type 1, range 32, base ef002000, size 12, enabled
pcib0: matched entry for 0.17.INTA (source \\_SB_.PCI0.LNKA)
pcib0: slot 17 INTA is routed to irq 11
found-> vendor=0x1000, dev=0x000f, revid=0x03
bus=0, slot=17, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x48 (2160 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=11
agp0: <VIA 82C8363 (Apollo KT133A) host to PCI bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 256M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xc000-0xcfff
pcib1: memory decode 0xec000000-0xedffffff
pcib1: prefetched decode 0xe0000000-0xe7ffffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 3, range 32, base e0000000, size 27, enabled
map[14]: type 4, range 32, base 0000c000, size 8, enabled
map[18]: type 1, range 32, base ed000000, size 16, enabled
pcib0: matched entry for 0.1.INTA (source \\_SB_.PCI0.LNKA)
pcib0: slot 1 INTA is routed to irq 11
pcib1: slot 0 INTA is routed to irq 11
found-> vendor=0x1002, dev=0x5144, revid=0x01
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686B UDMA100 controller> port 0xd000-0xd00f at device 7.1 on pci0
atapci0: Correcting VIA config for southbridge data corruption bug
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-slave: stat=0x00 err=0x08 lsb=0x00 msb=0x00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=50 ostat1=50
ata1-master: stat=0x50 err=0x01 lsb=0x14 msb=0xeb
ata1-slave: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 mask=03 stat0=50 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 5 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
ums0: Logitech Optical USB Mouse, rev 2.00/3.40, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhub0: port error, restarting port 2
uhub0: port error, giving up port 2
uhci1: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 5 at device 7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub1: port error, restarting port 1
uhub1: port error, giving up port 1
uhub1: port error, restarting port 2
uhub1: port error, giving up port 2
pci0: <bridge, PCI-unknown> at device 7.4 (no driver attached)
pcm0: <Creative EMU10K1> port 0xdc00-0xdc1f irq 5 at device 8.0 on pci0
emu: setmap (714000, 800), nseg=1, error=0
emu: setmap (773000, 1000), nseg=1, error=0
pcm0: <TriTech TR28602 AC97 Codec (id = 0x54524123)>
pcm0: Codec features 5 bit master volume, no 3D Stereo Enhancement
emu: setmap (6f6000, 1000), nseg=1, error=0
emu: setmap (6d8000, 1000), nseg=1, error=0
emu: setmap (792000, 1000), nseg=1, error=0
emu: setmap (790000, 1000), nseg=1, error=0
pcm0: sndbuf_setmap 2e92d000, 1000; 0xc5a99000 -> 2e92d000
pcm0: sndbuf_setmap 2e92b000, 1000; 0xc5a97000 -> 2e92b000
rl0: <D-Link DFE-530TX+ 10/100BaseTX> port 0xe400-0xe4ff mem 0xef003000-0xef0030ff irq 12 at device 9.0 on pci0
rl0: Ethernet address: 00:05:5d:4f:75:dc
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: bpf attached
fwohci0: <Lucent FW322/323> mem 0xef000000-0xef000fff irq 5 at device 11.0 on pci0
fwohci0: latency timer 32 -> 32.
fwohci0: cache size 8 -> 8.
fwohci0: [MPSAFE]
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 8.
fwohci0: EUI64 00:30:8d:01:21:32:d1:68
fwohci0: resetting OHCI...done (loop=0)
fwohci0: phy read failed(1).
fwohci0: fwphy_rddata: 0x2 loop=1, retry=1
fwohci0: fwphy_rddata: 0x3 loop=1, retry=0
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: Enable 1394a Enhancements
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: fwphy_rddata: 0x2 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: BUS_OPT 0xa002 -> 0xf800a002
fwohci0: fwohci_set_intr: 1
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
fwohci0: fw_set_bus_manager: 0->0 (loop=0)
firewire0: bus manager 0 (me)
send phy_config root_node=-1 gap_count=5
fwohci0: maxdesc: 2
fwohci0: start AT DMA status=0
ed0: <NE2000 PCI Ethernet (RealTek 8029)> port 0xe800-0xe81f irq 10 at device 13.0 on pci0
ed0: bpf attached
ed0: address 00:00:00:00:00:00, type NE2000 (16 bit)
ncr0: <ncr 53c875 fast20 wide scsi> port 0xec00-0xecff mem 0xef002000-0xef002fff,0xef001000-0xef0010ff irq 11 at device 17.0 on pci0
ncr0: minsync=12, maxsync=137, maxoffs=16, 128 dwords burst, large dma fifo
ncr0: single-ended, open drain IRQ driver, using on-chip SRAM
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x21 0x31 0x21 0x21
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1: irq maps: 0x21 0x29 0x21 0x21
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
unknown: not probed (disabled)
unknown: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: unable to allocate IRQ
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
ed: ed0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
vga: vga0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xcc000-0xcf7ff,0xc0000-0xcafff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
adv0 failed to probe on isa0
aha0 failed to probe on isa0
aic0 failed to probe on isa0
bt0 failed to probe on isa0
cs0 failed to probe at port 0x300 on isa0
fe0 failed to probe at port 0x300 on isa0
gusc0 failed to probe at port 0x220 irq 5 drq 1 flags 0x13 on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
pmtimer0 failed to probe on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0 failed to probe at port 0x300 irq 10 on isa0
vt0 failed to probe on isa0
isa_probe_children: probing PnP devices
Device configuration finished.
Timecounter "TSC" frequency 1000042613 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to deny, logging disabled
ata1: spurious interrupt - status=0x00 error=0x01
Current DB 0
ch = 0
Current OP KEY INT BR len Addr Depend Stat: Cnt
2e965000 OUTL ST2 ALL ALL 12 00000000 2e965080 8411:0009 RUN,ACTIVE, ack complete(11)
0x000000e0 0x00450000 0xffbaffff 0x00000000
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 2 steps (100% to 50.0%), currently 100.0%
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad0: setting UDMA100 on VIA 82C686B chip
GEOM: create disk ad0 dp=0xc5b80d70
ad0: <IC35L180AVV207-1/V26OA63A> ATA-6 disk at ata0-master
ad0: 176700MB (361882080 sectors), 359010 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
ata1-slave: pio=0x0c wdma=0x22 udma=0x42 cable=80pin
ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
acd0: setting UDMA33 on VIA 82C686B chip
acd0: <RICOH DVD+RW MP5125/1.38> CDRW drive at ata1 as master
acd0: read 5512KB/s (5512KB/s) write 2067KB/s (2067KB/s), 2048KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, packet
acd0: Writes: CDR, CDRW, test write
acd0: Audio: play, 15 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
acd1: setting UDMA33 on VIA 82C686B chip
acd1: <TOSHIBA DVD-ROM SD-M1612/1004> DVDROM drive at ata1 as slave
acd1: read 8268KB/s (8268KB/s), 512KB buffer, UDMA33
acd1: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd1: Writes:
acd1: Audio: play, 16 volume levels
acd1: Mechanism: ejectable tray, unlocked
acd1: Medium: CD-ROM 80mm data disc
Waiting 2 seconds for SCSI devices to settle
ncr0: restart (scsi reset).
[0] f:00 typ:6 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:110205837
[1] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:110205900 l:251674290
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 56425388544 end 56425420799
GEOM: Configure ad0s2, start 56425420800 length 128857236480 end 185282657279
GEOM: Configure ad0s2b, start 0 length 1572864000 end 1572863999
GEOM: Configure ad0s2c, start 0 length 128857236480 end 128857236479
GEOM: Configure ad0s2d, start 1572864000 length 127284372480 end 128857236479
bus_explore done
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe3:ata1:0:1:0): Retrying Command
(probe3:ata1:0:1:0): Recovered Sense
(probe3:ata1:0:1:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe3:ata1:0:1:0): CAM Status: SCSI Status Error
(probe3:ata1:0:1:0): SCSI Status: Check Condition
(probe3:ata1:0:1:0): ILLEGAL REQUEST asc:24,0
(probe3:ata1:0:1:0): Invalid field in CDB: Command byte 1 is invalid
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe3:ata1:0:1:0): Retrying Command
(probe3:ata1:0:1:0): Recovered Sense
(probe3:ata1:0:1:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe3:ata1:0:1:0): CAM Status: SCSI Status Error
(probe3:ata1:0:1:0): SCSI Status: Check Condition
(probe3:ata1:0:1:0): ILLEGAL REQUEST asc:24,0
(probe3:ata1:0:1:0): Invalid field in CDB: Command byte 1 is invalid
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe5:ncr0:0:1:0): Retrying Command
(probe7:ncr0:0:3:0): Retrying Command
(probe4:ncr0:0:0:0): Retrying Command
GEOM: create disk da0 dp=0xc5be2450
GEOM: create disk da1 dp=0xc5be9c50
GEOM: create disk da2 dp=0xc5bdc850
pass0 at ncr0 bus 0 target 0 lun 0
pass0: <QUANTUM FIREBALL ST3.2S 0F0C> Fixed Direct Access SCSI-2 device
pass0: Serial Number 153714142563
pass0: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
pass1 at ncr0 bus 0 target 1 lun 0
pass1: <FUJITSU M1606S-512 6C01> Fixed Direct Access SCSI-2 device
pass1: Serial Number 02004192
pass1: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
pass2 at ncr0 bus 0 target 3 lun 0
pass2: <IBM DCAS-34330 S61A> Fixed Direct Access SCSI-2 device
pass2: Serial Number B3FW8940
pass2: 20.000MB/s transfers (20.000MHz, offset 15)
pass3 at ata1 bus 0 target 0 lun 0
pass3: <RICOH DVD+RW MP5125 1.38> Removable CD-ROM SCSI-0 device
pass3: Serial Number 5
pass3: 33.000MB/s transfers
pass4 at ata1 bus 0 target 1 lun 0
pass4: <TOSHIBA DVD-ROM SD-M1612 1004> Removable CD-ROM SCSI-0 device
pass4: 33.000MB/s transfers
da1 at ncr0 bus 0 target 1 lun 0
da1: <FUJITSU M1606S-512 6C01> Fixed Direct Access SCSI-2 device
da1: Serial Number 02004192
da1: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da1: 1041MB (2131992 512 byte sectors: 255H 63S/T 132C)
da0 at ncr0 bus 0 target 0 lun 0
da0: <QUANTUM FIREBALL ST3.2S 0F0C> Fixed Direct Access SCSI-2 device
da0: Serial Number 153714142563
da0: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
da0: 3090MB (6328861 512 byte sectors: 255H 63S/T 393C)
(cd0:ata1:0:0:0): Retrying Command
GEOM: new disk da0
GEOM: new disk da1cd1 at ata1 bus 0 target 1 lun 0
cd1: <TOSHIBA DVD-ROM SD-M1612 1004> Removable CD-ROM SCSI-0 device
cd1: 33.000MB/s transfers
cd1: cd present [92307 x 2048 byte records]
GEOM: new disk da2
(cd0:ata1:0:0:0): Recovered Sense
(cd0:ata1:0:0:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(cd0:ata1:0:0:0): CAM Status: SCSI Status Error
(cd0:ata1:0:0:0): SCSI Status: Check Condition
(cd0:ata1:0:0:0): NOT READY asc:3a,0
(cd0:ata1:0:0:0): Medium not present
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
cd0 at ata1 bus 0 target 0 lun 0
cd0: <RICOH DVD+RW MP5125 1.38> Removable CD-ROM SCSI-0 device
cd0: Serial Number 5
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
da2 at ncr0 bus 0 target 3 lun 0
da2: <IBM DCAS-34330 S61A> Fixed Direct Access SCSI-2 device
da2: Serial Number B3FW8940
da2: 20.000MB/s transfers (20.000MHz, offset 15)
da2: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
[0] f:00 typ:6 s(CHS):0/1/1 e(CHS):49/63/32 s:32 l:102368
[1] f:80 typ:165 s(CHS):50/0/1 e(CHS):1023/63/32 s:102400 l:6225920
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 16384 length 52412416 end 52428799
GEOM: Configure da0s2, start 52428800 length 3187671040 end 3240099839
[0] f:00 typ:6 s(CHS):0/1/1 e(CHS):57/254/63 s:63 l:931707
[1] f:80 typ:165 s(CHS):58/0/1 e(CHS):131/254/63 s:931770 l:1188810
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da1s1, start 32256 length 477033984 end 477066239
GEOM: Configure da1s2, start 477066240 length 608670720 end 1085736959
GEOM: Configure da1a, start 1048576 length 104857600 end 105906175
GEOM: Configure da1b, start 105906176 length 33554432 end 139460607
GEOM: Configure da1c, start 0 length 1091579904 end 1091579903
GEOM: Configure da1d, start 0 length 1091579904 end 1091579903
GEOM: Configure da1e, start 139460608 length 104857600 end 244318207
GEOM: Configure da1f, start 244318208 length 67108864 end 311427071
GEOM: Configure da1g, start 311427072 length 780140544 end 1091567615
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):526/254/63 s:63 l:8466192
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da2s1, start 32256 length 4334690304 end 4334722559
GEOM: Configure da0s2a, start 0 length 141557760 end 141557759
GEOM: Configure da0s2c, start 0 length 3187671040 end 3187671039
GEOM: Configure da0s2e, start 141557760 length 3046113280 end 3187671039
GEOM: Configure da1s2c, start 0 length 608670720 end 608670719
GEOM: Configure da1s2d, start 0 length 419430400 end 419430399
GEOM: Configure da1s2e, start 419430400 length 189240320 end 608670719
GEOM: Configure da2s1b, start 0 length 402653184 end 402653183
GEOM: Configure da2s1c, start 0 length 4334690304 end 4334690303
GEOM: Configure da2s1e, start 402653184 length 3932037120 end 4334690303
Mounting root from ufs:/dev/da0s2a
start_init: trying /sbin/init
GEOM: Configure da1a, start 1048576 length 104857600 end 105906175
GEOM: Configure da1b, start 105906176 length 33554432 end 139460607
GEOM: Configure da1c, start 0 length 1091579904 end 1091579903
GEOM: Configure da1d, start 0 length 1091579904 end 1091579903
GEOM: Configure da1e, start 139460608 length 104857600 end 244318207
GEOM: Configure da1f, start 244318208 length 67108864 end 311427071
GEOM: Configure da1g, start 311427072 length 780140544 end 1091567615
GEOM: Configure da1a, start 1048576 length 104857600 end 105906175
GEOM: Configure da1b, start 105906176 length 33554432 end 139460607
GEOM: Configure da1c, start 0 length 1091579904 end 1091579903
GEOM: Configure da1d, start 0 length 1091579904 end 1091579903
GEOM: Configure da1e, start 139460608 length 104857600 end 244318207
GEOM: Configure da1f, start 244318208 length 67108864 end 311427071
GEOM: Configure da1g, start 311427072 length 780140544 end 1091567615
procfs registered
lock order reversal
1st 0xc5d2a8b4 inp (inp) @ netinet/udp_usrreq.c:1042
2nd 0xc036a30c div (div) @ netinet/ip_divert.c:225
Stack backtrace:
tun0: bpf attached
tun1: bpf attached
tun2: bpf attached
tun3: bpf attached
tun4: bpf attached
splash: image decoder found: logo_saver
ed0: promiscuous mode enabled
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Queue Full
(da0:ncr0:0:0:0): tagged openings now 8
(da0:ncr0:0:0:0): Retrying Command
--envbJBWh7q8WU6mo
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.2"
1 12 14 15] low,level,sharable 0.7.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.3
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.3
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.3
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.0
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.2
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.3
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.0
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.1
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.2
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.3
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.0
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.1
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.2
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.3
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.0
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.1
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.2
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.3
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.8.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.8.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.8.2
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.8.3
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.0
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.1
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.2
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.3
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.3
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.3
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base e8000000, size 26, enabled
found-> vendor=0x1106, dev=0x0305, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x08 (240 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x8305, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x2230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x0686, revid=0x40
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000d000, size 4, enabled
found-> vendor=0x1106, dev=0x0571, revid=0x06
bus=0, slot=7, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000d400, size 5, enabled
pcib0: matched entry for 0.7.INTD (source \\_SB_.PCI0.LNKD)
pcib0: slot 7 INTD is routed to irq 5
found-> vendor=0x1106, dev=0x3038, revid=0x16
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=5
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000d800, size 5, enabled
pcib0: matched entry for 0.7.INTD (source \\_SB_.PCI0.LNKD)
pcib0: slot 7 INTD is routed to irq 5
found-> vendor=0x1106, dev=0x3038, revid=0x16
bus=0, slot=7, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=5
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x3057, revid=0x40
bus=0, slot=7, func=4
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000dc00, size 5, enabled
pcib0: matched entry for 0.8.INTA (source \\_SB_.PCI0.LNKD)
pcib0: slot 8 INTA is routed to irq 5
found-> vendor=0x1102, dev=0x0002, revid=0x08
bus=0, slot=8, func=0
class=04-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x14 (5000 ns)
intpin=a, irq=5
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e000, size 3, enabled
found-> vendor=0x1102, dev=0x7002, revid=0x08
bus=0, slot=8, func=1
class=09-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e400, size 8, enabled
map[14]: type 1, range 32, base ef003000, size 8, enabled
pcib0: matched entry for 0.9.INTA (source \\_SB_.PCI0.LNKC)
pcib0: slot 9 INTA is routed to irq 12
found-> vendor=0x1186, dev=0x1300, revid=0x10
bus=0, slot=9, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=12
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ef000000, size 12, enabled
pcib0: matched entry for 0.11.INTA (source \\_SB_.PCI0.LNKD)
pcib0: slot 11 INTA is routed to irq 5
found-> vendor=0x11c1, dev=0x5811, revid=0x04
bus=0, slot=11, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x0c (3000 ns), maxlat=0x18 (6000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e800, size 5, enabled
pcib0: matched entry for 0.13.INTA (source \\_SB_.PCI0.LNKB)
pcib0: slot 13 INTA is routed to irq 10
found-> vendor=0x10ec, dev=0x8029, revid=0x00
bus=0, slot=13, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
map[10]: type 4, range 32, base 0000ec00, size 8, enabled
map[14]: type 1, range 32, base ef001000, size 8, enabled
map[18]: type 1, range 32, base ef002000, size 12, enabled
pcib0: matched entry for 0.17.INTA (source \\_SB_.PCI0.LNKA)
pcib0: slot 17 INTA is routed to irq 11
found-> vendor=0x1000, dev=0x000f, revid=0x03
bus=0, slot=17, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x48 (2160 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=11
agp0: <VIA 82C8363 (Apollo KT133A) host to PCI bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 256M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xc000-0xcfff
pcib1: memory decode 0xec000000-0xedffffff
pcib1: prefetched decode 0xe0000000-0xe7ffffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 3, range 32, base e0000000, size 27, enabled
map[14]: type 4, range 32, base 0000c000, size 8, enabled
map[18]: type 1, range 32, base ed000000, size 16, enabled
pcib0: matched entry for 0.1.INTA (source \\_SB_.PCI0.LNKA)
pcib0: slot 1 INTA is routed to irq 11
pcib1: slot 0 INTA is routed to irq 11
found-> vendor=0x1002, dev=0x5144, revid=0x01
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686B UDMA100 controller> port 0xd000-0xd00f at device 7.1 on pci0
atapci0: Correcting VIA config for southbridge data corruption bug
ata0: reset tp1 mask=03 ostat0=50 ostat1=50
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-slave: stat=0x50 err=0x01 lsb=0x14 msb=0xeb
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=50 devices=0x9<ATAPI_SLAVE,ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=50 ostat1=50
ata1-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata1-slave: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 mask=03 stat0=50 stat1=00 devices=0x9<ATAPI_SLAVE,ATA_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 5 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
ums0: Logitech Optical USB Mouse, rev 2.00/3.40, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhub0: port error, restarting port 2
uhub0: port error, giving up port 2
uhci1: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 5 at device 7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub1: port error, restarting port 1
uhub1: port error, giving up port 1
uhub1: port error, restarting port 2
uhub1: port error, giving up port 2
pci0: <bridge, PCI-unknown> at device 7.4 (no driver attached)
pcm0: <Creative EMU10K1> port 0xdc00-0xdc1f irq 5 at device 8.0 on pci0
emu: setmap (714000, 800), nseg=1, error=0
emu: setmap (773000, 1000), nseg=1, error=0
pcm0: <TriTech TR28602 AC97 Codec (id = 0x54524123)>
pcm0: Codec features 5 bit master volume, no 3D Stereo Enhancement
emu: setmap (6f6000, 1000), nseg=1, error=0
emu: setmap (6d8000, 1000), nseg=1, error=0
emu: setmap (792000, 1000), nseg=1, error=0
emu: setmap (790000, 1000), nseg=1, error=0
pcm0: sndbuf_setmap 2e92d000, 1000; 0xc5a99000 -> 2e92d000
pcm0: sndbuf_setmap 2e92b000, 1000; 0xc5a97000 -> 2e92b000
rl0: <D-Link DFE-530TX+ 10/100BaseTX> port 0xe400-0xe4ff mem 0xef003000-0xef0030ff irq 12 at device 9.0 on pci0
rl0: Ethernet address: 00:05:5d:4f:75:dc
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: bpf attached
fwohci0: <Lucent FW322/323> mem 0xef000000-0xef000fff irq 5 at device 11.0 on pci0
fwohci0: latency timer 32 -> 32.
fwohci0: cache size 8 -> 8.
fwohci0: [MPSAFE]
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 8.
fwohci0: EUI64 00:30:8d:01:21:32:d1:68
fwohci0: resetting OHCI...done (loop=0)
fwohci0: phy read failed(1).
fwohci0: fwphy_rddata: 0x2 loop=1, retry=1
fwohci0: fwphy_rddata: 0x3 loop=1, retry=0
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: Enable 1394a Enhancements
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: fwphy_rddata: 0x2 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: BUS_OPT 0xa002 -> 0xf800a002
fwohci0: fwohci_set_intr: 1
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
fwohci0: fw_set_bus_manager: 0->0 (loop=0)
firewire0: bus manager 0 (me)
send phy_config root_node=-1 gap_count=5
fwohci0: maxdesc: 2
fwohci0: start AT DMA status=0
ed0: <NE2000 PCI Ethernet (RealTek 8029)> port 0xe800-0xe81f irq 10 at device 13.0 on pci0
ed0: bpf attached
ed0: address 52:54:05:de:2f:64, type NE2000 (16 bit)
ncr0: <ncr 53c875 fast20 wide scsi> port 0xec00-0xecff mem 0xef002000-0xef002fff,0xef001000-0xef0010ff irq 11 at device 17.0 on pci0
ncr0: minsync=12, maxsync=137, maxoffs=16, 128 dwords burst, large dma fifo
ncr0: single-ended, open drain IRQ driver, using on-chip SRAM
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x21 0x31 0x21 0x21
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1: irq maps: 0x21 0x29 0x21 0x21
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
unknown: not probed (disabled)
unknown: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: unable to allocate IRQ
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
ed: ed0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
vga: vga0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xcc000-0xcf7ff,0xc0000-0xcafff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
adv0 failed to probe on isa0
aha0 failed to probe on isa0
aic0 failed to probe on isa0
bt0 failed to probe on isa0
cs0 failed to probe at port 0x300 on isa0
fe0 failed to probe at port 0x300 on isa0
gusc0 failed to probe at port 0x220 irq 5 drq 1 flags 0x13 on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
pmtimer0 failed to probe on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0 failed to probe at port 0x300 irq 10 on isa0
vt0 failed to probe on isa0
isa_probe_children: probing PnP devices
Device configuration finished.
Timecounter "TSC" frequency 1000043934 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to deny, logging disabled
ata1: spurious interrupt - status=0x00 error=0x01
Current DB 0
ch = 0
Current OP KEY INT BR len Addr Depend Stat: Cnt
2e965000 OUTL ST2 ALL ALL 12 00000000 2e965080 8411:0009 RUN,ACTIVE, ack complete(11)
0x000000e0 0x00450000 0xffbaffff 0x00000000
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 2 steps (100% to 50.0%), currently 100.0%
ata0-slave: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=40pin
ad0: DMA limited to UDMA33, non-ATA66 cable or device
ad0: setting UDMA33 on VIA 82C686B chip
GEOM: create disk ad0 dp=0xc5b80d70
ad0: <IC35L180AVV207-1/V26OA63A> ATA-6 disk at ata0-master
ad0: 176700MB (361882080 sectors), 359010 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
GEOM: new disk ad0
[0] f:00 typ:6 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:110205837
[1] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:110205900 l:251674290
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 56425388544 end 56425420799
GEOM: Configure ad0s2, start 56425420800 length 128857236480 end 185282657279
acd0: setting UDMA33 on VIA 82C686B chip
acd0: <RICOH DVD+RW MP5125/1.38> CDRW drive at ata0 as slave
acd0: read 5512KB/s (5512KB/s) write 2067KB/s (2067KB/s), 2048KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, packet
acd0: Writes: CDR, CDRW, test write
acd0: Audio: play, 15 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata1-slave: pio=0x0c wdma=0x22 udma=0x42 cable=80pin
ata1-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad1: setting UDMA100 on VIA 82C686B chip
GEOM: create disk ad1 dp=0xc5bd4970
ad1: <WDC WD800BB-32CAA0/16.06V16> ATA-5 disk at ata1-master
ad1: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B
ad1: 16 secs/int, 1 depth queue, UDMA100
acd1: setting UDMA33 on VIA 82C686B chip
acd1: <TOSHIBA DVD-ROM SD-M1612/1004> DVDROM drive at ata1 as slave
acd1: read 8268KB/s (8268KB/s), 512KB buffer, UDMA33
acd1: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd1: Writes:
acd1: Audio: play, 16 volume levels
acd1: Mechanism: ejectable tray, unlocked
acd1: Medium: CD-ROM 80mm data disc
Waiting 2 seconds for SCSI devices to settle
ncr0: restart (scsi reset).
GEOM: Configure ad0s2b, start 0 length 1572864000 end 1572863999
GEOM: Configure ad0s2c, start 0 length 128857236480 end 128857236479
GEOM: Configure ad0s2d, start 1572864000 length 127284372480 end 128857236479
GEOM: new disk ad1
[0] f:80 typ:6 s(CHS):0/1/1 e(CHS):1023/137/60 s:60 l:104849580
[1] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/137/60 s:104849640 l:51443640
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad1s1, start 30720 length 53682984960 end 53683015679
GEOM: Configure ad1s2, start 53683015680 length 26339143680 end 80022159359
GEOM: Configure ad1s2b, start 0 length 1073741824 end 1073741823
GEOM: Configure ad1s2c, start 0 length 26339143680 end 26339143679
GEOM: Configure ad1s2e, start 1073741824 length 25265401856 end 26339143679
bus_explore done
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe2:ata1:0:0:0): error 22
(probe2:ata1:0:0:0): Unretryable Error
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe2:ata1:0:0:0): error 22
(probe2:ata1:0:0:0): Unretryable Error
(probe3:ata1:0:1:0): Retrying Command
(probe3:ata1:0:1:0): Recovered Sense
(probe3:ata1:0:1:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe3:ata1:0:1:0): CAM Status: SCSI Status Error
(probe3:ata1:0:1:0): SCSI Status: Check Condition
(probe3:ata1:0:1:0): ILLEGAL REQUEST asc:24,0
(probe3:ata1:0:1:0): Invalid field in CDB: Command byte 1 is invalid
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe3:ata1:0:1:0): Retrying Command
(probe3:ata1:0:1:0): Recovered Sense
(probe3:ata1:0:1:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe3:ata1:0:1:0): CAM Status: SCSI Status Error
(probe3:ata1:0:1:0): SCSI Status: Check Condition
(probe3:ata1:0:1:0): ILLEGAL REQUEST asc:24,0
(probe3:ata1:0:1:0): Invalid field in CDB: Command byte 1 is invalid
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe7:ncr0:0:3:0): Retrying Command
(probe4:ncr0:0:0:0): Retrying Command
GEOM: create disk da0 dp=0xc5b3d850
GEOM: create disk da1 dp=0xc5b3f450
pass0 at ncr0 bus 0 target 0 lun 0
pass0: <QUANTUM FIREBALL ST3.2S 0F0C> Fixed Direct Access SCSI-2 device
pass0: Serial Number 153714142563
pass0: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
pass1 at ncr0 bus 0 target 3 lun 0
pass1: <IBM DCAS-34330 S61A> Fixed Direct Access SCSI-2 device
pass1: Serial Number B3FW8940
pass1: 20.000MB/s transfers (20.000MHz, offset 15)
pass2 at ata0 bus 0 target 1 lun 0
pass2: <RICOH DVD+RW MP5125 1.38> Removable CD-ROM SCSI-0 device
pass2: Serial Number 5
pass2: 33.000MB/s transfers
pass3 at ata1 bus 0 target 1 lun 0
pass3: <TOSHIBA DVD-ROM SD-M1612 1004> Removable CD-ROM SCSI-0 device
pass3: 33.000MB/s transfers
da0 at ncr0 bus 0 target 0 lun 0
da0: <QUANTUM FIREBALL ST3.2S 0F0C> Fixed Direct Access SCSI-2 device
da0: Serial Number 153714142563
da0: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
da0: 3090MB (6328861 512 byte sectors: 255H 63S/T 393C)
(cd0:ata0:0:1:0): Retrying Command
cd1 at ata1 bus 0 target 1 lun 0
cd1: <TOSHIBA DVD-ROM SD-M1612 1004> Removable CD-ROM SCSI-0 device
cd1: 33.000MB/s transfers
cd1: cd present [92307 x 2048 byte records]
(cd0:ata0:0:1:0): Recovered Sense
(cd0:ata0:0:1:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(cd0:ata0:0:1:0): CAM Status: SCSI Status Error
(cd0:ata0:0:1:0): SCSI Status: Check Condition
(cd0:ata0:0:1:0): NOT READY asc:3a,0
(cd0:ata0:0:1:0): Medium not present
(cd0:ata0:0:1:0): error 6
(cd0:ata0:0:1:0): Unretryable Error
cd0 at ata0 bus 0 target 1 lun 0
cd0: <RICOH DVD+RW MP5125 1.38> Removable CD-ROM SCSI-0 device
cd0: Serial Number 5
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
GEOM: new disk da0
GEOM: new disk da1
da1 at ncr0 bus 0 target 3 lun 0
da1: <IBM DCAS-34330 S61A> Fixed Direct Access SCSI-2 device
da1: Serial Number B3FW8940
da1: 20.000MB/s transfers (20.000MHz, offset 15)
da1: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
[0] f:00 typ:6 s(CHS):0/1/1 e(CHS):49/63/32 s:32 l:102368
[1] f:80 typ:165 s(CHS):50/0/1 e(CHS):1023/63/32 s:102400 l:6225920
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 16384 length 52412416 end 52428799
GEOM: Configure da0s2, start 52428800 length 3187671040 end 3240099839
[0] f:00 typ:6 s(CHS):0/1/1 e(CHS):390/254/63 s:63 l:6281352
[1] f:80 typ:165 s(CHS):391/0/1 e(CHS):526/254/63 s:6281415 l:2184840
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da1s1, start 32256 length 3216052224 end 3216084479
GEOM: Configure da1s2, start 3216084480 length 1118638080 end 4334722559
GEOM: Configure da0s2a, start 0 length 141557760 end 141557759
GEOM: Configure da0s2c, start 0 length 3187671040 end 3187671039
GEOM: Configure da0s2e, start 141557760 length 3046113280 end 3187671039
GEOM: Configure da1s2c, start 0 length 1118638080 end 1118638079
GEOM: Configure da1s2d, start 0 length 838860800 end 838860799
GEOM: Configure da1s2e, start 838860800 length 279777280 end 1118638079
Mounting root from ufs:/dev/da0s2a
start_init: trying /sbin/init
procfs registered
lock order reversal
1st 0xc5d128b4 inp (inp) @ netinet/udp_usrreq.c:1042
2nd 0xc036a30c div (div) @ netinet/ip_divert.c:225
Stack backtrace:
tun0: bpf attached
tun1: bpf attached
tun2: bpf attached
tun3: bpf attached
tun4: bpf attached
splash: image decoder found: logo_saver
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Queue Full
(da0:ncr0:0:0:0): tagged openings now 8
(da0:ncr0:0:0:0): Retrying Command
ed0: promiscuous mode enabled
drm0: <ATI Radeon QD R100> port 0xc000-0xc0ff mem 0xed000000-0xed00ffff,0xe0000000-0xe7ffffff irq 11 at device 0.0 on pci1
info: [drm] AGP at 0xe8000000 64MB
info: [drm] Initialized radeon 1.9.0 20020828 on minor 0
drm0: [MPSAFE]
--envbJBWh7q8WU6mo
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.3"
_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.3
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.3
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.0
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.2
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.3
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.0
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.1
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.2
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.3
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.0
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.1
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.2
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.3
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.0
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.1
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.2
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.3
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.8.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.8.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.8.2
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.8.3
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.0
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.1
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.2
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.19.3
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.3
\\_SB_.PCI0.LNKA irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.1
\\_SB_.PCI0.LNKC irq 12: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.2
\\_SB_.PCI0.LNKD irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.3
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base e8000000, size 26, enabled
found-> vendor=0x1106, dev=0x0305, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x08 (240 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x8305, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x2230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x0686, revid=0x40
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000d000, size 4, enabled
found-> vendor=0x1106, dev=0x0571, revid=0x06
bus=0, slot=7, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000d400, size 5, enabled
pcib0: matched entry for 0.7.INTD (source \\_SB_.PCI0.LNKD)
pcib0: slot 7 INTD is routed to irq 5
found-> vendor=0x1106, dev=0x3038, revid=0x16
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=5
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000d800, size 5, enabled
pcib0: matched entry for 0.7.INTD (source \\_SB_.PCI0.LNKD)
pcib0: slot 7 INTD is routed to irq 5
found-> vendor=0x1106, dev=0x3038, revid=0x16
bus=0, slot=7, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=5
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x3057, revid=0x40
bus=0, slot=7, func=4
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000dc00, size 5, enabled
pcib0: matched entry for 0.8.INTA (source \\_SB_.PCI0.LNKD)
pcib0: slot 8 INTA is routed to irq 5
found-> vendor=0x1102, dev=0x0002, revid=0x08
bus=0, slot=8, func=0
class=04-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x14 (5000 ns)
intpin=a, irq=5
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e000, size 3, enabled
found-> vendor=0x1102, dev=0x7002, revid=0x08
bus=0, slot=8, func=1
class=09-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e400, size 8, enabled
map[14]: type 1, range 32, base ef003000, size 8, enabled
pcib0: matched entry for 0.9.INTA (source \\_SB_.PCI0.LNKC)
pcib0: slot 9 INTA is routed to irq 12
found-> vendor=0x1186, dev=0x1300, revid=0x10
bus=0, slot=9, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=12
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ef000000, size 12, enabled
pcib0: matched entry for 0.11.INTA (source \\_SB_.PCI0.LNKD)
pcib0: slot 11 INTA is routed to irq 5
found-> vendor=0x11c1, dev=0x5811, revid=0x04
bus=0, slot=11, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x0c (3000 ns), maxlat=0x18 (6000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e800, size 5, enabled
pcib0: matched entry for 0.13.INTA (source \\_SB_.PCI0.LNKB)
pcib0: slot 13 INTA is routed to irq 10
found-> vendor=0x10ec, dev=0x8029, revid=0x00
bus=0, slot=13, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
map[10]: type 4, range 32, base 0000ec00, size 8, enabled
map[14]: type 1, range 32, base ef001000, size 8, enabled
map[18]: type 1, range 32, base ef002000, size 12, enabled
pcib0: matched entry for 0.17.INTA (source \\_SB_.PCI0.LNKA)
pcib0: slot 17 INTA is routed to irq 11
found-> vendor=0x1000, dev=0x000f, revid=0x03
bus=0, slot=17, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x48 (2160 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=11
agp0: <VIA 82C8363 (Apollo KT133A) host to PCI bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 256M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xc000-0xcfff
pcib1: memory decode 0xec000000-0xedffffff
pcib1: prefetched decode 0xe0000000-0xe7ffffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 3, range 32, base e0000000, size 27, enabled
map[14]: type 4, range 32, base 0000c000, size 8, enabled
map[18]: type 1, range 32, base ed000000, size 16, enabled
pcib0: matched entry for 0.1.INTA (source \\_SB_.PCI0.LNKA)
pcib0: slot 1 INTA is routed to irq 11
pcib1: slot 0 INTA is routed to irq 11
found-> vendor=0x1002, dev=0x5144, revid=0x01
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686B UDMA100 controller> port 0xd000-0xd00f at device 7.1 on pci0
atapci0: Correcting VIA config for southbridge data corruption bug
ata0: reset tp1 mask=03 ostat0=50 ostat1=50
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=50 ostat1=50
ata1-master: stat=0xd0 err=0x00 lsb=0xaa msb=0xff
ata1-slave: stat=0xd0 err=0x00 lsb=0xaa msb=0xff
ata1-master: stat=0xd0 err=0x00 lsb=0xaa msb=0xff
ata1-slave: stat=0xd0 err=0x00 lsb=0xaa msb=0xff
ata1-master: stat=0xd0 err=0x00 lsb=0xaa msb=0xff
ata1-slave: stat=0xd0 err=0x00 lsb=0xaa msb=0xff
ata1-master: stat=0x50 err=0x01 lsb=0x14 msb=0xeb
ata1-slave: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 mask=03 stat0=50 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 5 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
ums0: Logitech Optical USB Mouse, rev 2.00/3.40, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhub0: port error, restarting port 2
uhub0: port error, giving up port 2
uhci1: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 5 at device 7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub1: port error, restarting port 1
uhub1: port error, giving up port 1
uhub1: port error, restarting port 2
uhub1: port error, giving up port 2
pci0: <bridge, PCI-unknown> at device 7.4 (no driver attached)
pcm0: <Creative EMU10K1> port 0xdc00-0xdc1f irq 5 at device 8.0 on pci0
emu: setmap (714000, 800), nseg=1, error=0
emu: setmap (773000, 1000), nseg=1, error=0
pcm0: <TriTech TR28602 AC97 Codec (id = 0x54524123)>
pcm0: Codec features 5 bit master volume, no 3D Stereo Enhancement
emu: setmap (6f6000, 1000), nseg=1, error=0
emu: setmap (6d8000, 1000), nseg=1, error=0
emu: setmap (792000, 1000), nseg=1, error=0
emu: setmap (790000, 1000), nseg=1, error=0
pcm0: sndbuf_setmap 2e92d000, 1000; 0xc5a99000 -> 2e92d000
pcm0: sndbuf_setmap 2e92b000, 1000; 0xc5a97000 -> 2e92b000
rl0: <D-Link DFE-530TX+ 10/100BaseTX> port 0xe400-0xe4ff mem 0xef003000-0xef0030ff irq 12 at device 9.0 on pci0
rl0: Ethernet address: 00:05:5d:4f:75:dc
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: bpf attached
fwohci0: <Lucent FW322/323> mem 0xef000000-0xef000fff irq 5 at device 11.0 on pci0
fwohci0: latency timer 32 -> 32.
fwohci0: cache size 8 -> 8.
fwohci0: [MPSAFE]
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channel is 8.
fwohci0: EUI64 00:30:8d:01:21:32:d1:68
fwohci0: resetting OHCI...done (loop=0)
fwohci0: phy read failed(1).
fwohci0: fwphy_rddata: 0x2 loop=1, retry=1
fwohci0: fwphy_rddata: 0x3 loop=1, retry=0
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: Enable 1394a Enhancements
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: fwphy_rddata: 0x2 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: BUS_OPT 0xa002 -> 0xf800a002
fwohci0: fwohci_set_intr: 1
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
fwohci0: fw_set_bus_manager: 0->0 (loop=0)
firewire0: bus manager 0 (me)
send phy_config root_node=-1 gap_count=5
fwohci0: maxdesc: 2
fwohci0: start AT DMA status=0
ed0: <NE2000 PCI Ethernet (RealTek 8029)> port 0xe800-0xe81f irq 10 at device 13.0 on pci0
ed0: bpf attached
ed0: address 52:54:05:de:2f:64, type NE2000 (16 bit)
ncr0: <ncr 53c875 fast20 wide scsi> port 0xec00-0xecff mem 0xef002000-0xef002fff,0xef001000-0xef0010ff irq 11 at device 17.0 on pci0
ncr0: minsync=12, maxsync=137, maxoffs=16, 128 dwords burst, large dma fifo
ncr0: single-ended, open drain IRQ driver, using on-chip SRAM
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x21 0x31 0x21 0x21
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1: irq maps: 0x21 0x29 0x21 0x21
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
unknown: not probed (disabled)
unknown: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: unable to allocate IRQ
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
ed: ed0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
vga: vga0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xcc000-0xcf7ff,0xc0000-0xcafff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
adv0 failed to probe on isa0
aha0 failed to probe on isa0
aic0 failed to probe on isa0
bt0 failed to probe on isa0
cs0 failed to probe at port 0x300 on isa0
fe0 failed to probe at port 0x300 on isa0
gusc0 failed to probe at port 0x220 irq 5 drq 1 flags 0x13 on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
pmtimer0 failed to probe on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0 failed to probe at port 0x300 irq 10 on isa0
vt0 failed to probe on isa0
isa_probe_children: probing PnP devices
Device configuration finished.
Timecounter "TSC" frequency 1000044612 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to deny, logging disabled
ata1: spurious interrupt - status=0x00 error=0x01
Current DB 0
ch = 0
Current OP KEY INT BR len Addr Depend Stat: Cnt
2e965000 OUTL ST2 ALL ALL 12 00000000 2e965080 8411:0009 RUN,ACTIVE, ack complete(11)
0x000000e0 0x00450000 0xffbaffff 0x00000000
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 2 steps (100% to 50.0%), currently 100.0%
ata0-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad0: setting UDMA100 on VIA 82C686B chip
GEOM: create disk ad0 dp=0xc5b80d70
ad0: <IC35L180AVV207-1/V26OA63A> ATA-6 disk at ata0-master
ad0: 176700MB (361882080 sectors), 359010 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
[0] f:00 typ:6 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:110205837
[1] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:110205900 l:251674290
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 56425388544 end 56425420799
GEOM: Configure ad0s2, start 56425420800 length 128857236480 end 185282657279
ad1: setting UDMA100 on VIA 82C686B chip
GEOM: create disk ad1 dp=0xc5b80a70
ad1: <WDC WD800BB-32CAA0/16.06V16> ATA-5 disk at ata0-slave
ad1: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B
ad1: 16 secs/int, 1 depth queue, UDMA100
ata1-slave: pio=0x0c wdma=0x22 udma=0x42 cable=80pin
ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
acd0: setting UDMA33 on VIA 82C686B chip
acd0: <RICOH DVD+RW MP5125/1.38> CDRW drive at ata1 as master
acd0: read 5512KB/s (5512KB/s) write 2067KB/s (2067KB/s), 2048KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, packet
acd0: Writes: CDR, CDRW, test write
acd0: Audio: play, 15 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
acd1: setting UDMA33 on VIA 82C686B chip
acd1: <TOSHIBA DVD-ROM SD-M1612/1004> DVDROM drive at ata1 as slave
acd1: read 8268KB/s (8268KB/s), 512KB buffer, UDMA33
acd1: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd1: Writes:
acd1: Audio: play, 16 volume levels
acd1: Mechanism: ejectable tray, unlocked
acd1: Medium: CD-ROM 80mm data disc
Waiting 2 seconds for SCSI devices to settle
ncr0: restart (scsi reset).
GEOM: Configure ad0s2b, start 0 length 1572864000 end 1572863999
GEOM: Configure ad0s2c, start 0 length 128857236480 end 128857236479
GEOM: Configure ad0s2d, start 1572864000 length 127284372480 end 128857236479
GEOM: new disk ad1
[0] f:80 typ:6 s(CHS):0/1/1 e(CHS):1023/137/60 s:60 l:104849580
[1] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/137/60 s:104849640 l:51443640
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad1s1, start 30720 length 53682984960 end 53683015679
GEOM: Configure ad1s2, start 53683015680 length 26339143680 end 80022159359
GEOM: Configure ad1s2b, start 0 length 1073741824 end 1073741823
GEOM: Configure ad1s2c, start 0 length 26339143680 end 26339143679
GEOM: Configure ad1s2e, start 1073741824 length 25265401856 end 26339143679
bus_explore done
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe0:ata0:0:0:0): error 22
(probe0:ata0:0:0:0): Unretryable Error
(probe1:ata0:0:1:0): error 22
(probe1:ata0:0:1:0): Unretryable Error
(probe3:ata1:0:1:0): Retrying Command
(probe3:ata1:0:1:0): Recovered Sense
(probe3:ata1:0:1:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe3:ata1:0:1:0): CAM Status: SCSI Status Error
(probe3:ata1:0:1:0): SCSI Status: Check Condition
(probe3:ata1:0:1:0): ILLEGAL REQUEST asc:24,0
(probe3:ata1:0:1:0): Invalid field in CDB: Command byte 1 is invalid
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe3:ata1:0:1:0): Retrying Command
(probe3:ata1:0:1:0): Recovered Sense
(probe3:ata1:0:1:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe3:ata1:0:1:0): CAM Status: SCSI Status Error
(probe3:ata1:0:1:0): SCSI Status: Check Condition
(probe3:ata1:0:1:0): ILLEGAL REQUEST asc:24,0
(probe3:ata1:0:1:0): Invalid field in CDB: Command byte 1 is invalid
(probe3:ata1:0:1:0): error 22
(probe3:ata1:0:1:0): Unretryable Error
(probe7:ncr0:0:3:0): Retrying Command
(probe4:ncr0:0:0:0): Retrying Command
GEOM: create disk da0 dp=0xc5b3d850
GEOM: create disk da1 dp=0xc5b3e450
pass0 at ncr0 bus 0 target 0 lun 0
pass0: <QUANTUM FIREBALL ST3.2S 0F0C> Fixed Direct Access SCSI-2 device
pass0: Serial Number 153714142563
pass0: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
pass1 at ncr0 bus 0 target 3 lun 0
pass1: <IBM DCAS-34330 S61A> Fixed Direct Access SCSI-2 device
pass1: Serial Number B3FW8940
pass1: 20.000MB/s transfers (20.000MHz, offset 15)
pass2 at ata1 bus 0 target 0 lun 0
pass2: <RICOH DVD+RW MP5125 1.38> Removable CD-ROM SCSI-0 device
pass2: Serial Number 5
pass2: 33.000MB/s transfers
pass3 at ata1 bus 0 target 1 lun 0
pass3: <TOSHIBA DVD-ROM SD-M1612 1004> Removable CD-ROM SCSI-0 device
pass3: 33.000MB/s transfers
da0 at ncr0 bus 0 target 0 lun 0
da0: <QUANTUM FIREBALL ST3.2S 0F0C> Fixed Direct Access SCSI-2 device
da0: Serial Number 153714142563
da0: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
da0: 3090MB (6328861 512 byte sectors: 255H 63S/T 393C)
(cd0:ata1:0:0:0): Retrying Command
cd1 at ata1 bus 0 target 1 lun 0
cd1: <TOSHIBA DVD-ROM SD-M1612 1004> Removable CD-ROM SCSI-0 device
cd1: 33.000MB/s transfers
cd1: cd present [92307 x 2048 byte records]
(cd0:ata1:0:0:0): Recovered Sense
(cd0:ata1:0:0:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(cd0:ata1:0:0:0): CAM Status: SCSI Status Error
(cd0:ata1:0:0:0): SCSI Status: Check Condition
(cd0:ata1:0:0:0): NOT READY asc:3a,0
(cd0:ata1:0:0:0): Medium not present
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
cd0 at ata1 bus 0 target 0 lun 0
cd0: <RICOH DVD+RW MP5125 1.38> Removable CD-ROM SCSI-0 device
cd0: Serial Number 5
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
GEOM: new disk da0
GEOM: new disk da1
da1 at ncr0 bus 0 target 3 lun 0
da1: <IBM DCAS-34330 S61A> Fixed Direct Access SCSI-2 device
da1: Serial Number B3FW8940
da1: 20.000MB/s transfers (20.000MHz, offset 15)
da1: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
[0] f:00 typ:6 s(CHS):0/1/1 e(CHS):49/63/32 s:32 l:102368
[1] f:80 typ:165 s(CHS):50/0/1 e(CHS):1023/63/32 s:102400 l:6225920
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 16384 length 52412416 end 52428799
GEOM: Configure da0s2, start 52428800 length 3187671040 end 3240099839
[0] f:00 typ:6 s(CHS):0/1/1 e(CHS):390/254/63 s:63 l:6281352
[1] f:80 typ:165 s(CHS):391/0/1 e(CHS):526/254/63 s:6281415 l:2184840
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da1s1, start 32256 length 3216052224 end 3216084479
GEOM: Configure da1s2, start 3216084480 length 1118638080 end 4334722559
GEOM: Configure da0s2a, start 0 length 141557760 end 141557759
GEOM: Configure da0s2c, start 0 length 3187671040 end 3187671039
GEOM: Configure da0s2e, start 141557760 length 3046113280 end 3187671039
GEOM: Configure da1s2c, start 0 length 1118638080 end 1118638079
GEOM: Configure da1s2d, start 0 length 838860800 end 838860799
GEOM: Configure da1s2e, start 838860800 length 279777280 end 1118638079
Mounting root from ufs:/dev/da0s2a
start_init: trying /sbin/init
procfs registered
lock order reversal
1st 0xc5d128b4 inp (inp) @ netinet/udp_usrreq.c:1042
2nd 0xc036a30c div (div) @ netinet/ip_divert.c:225
Stack backtrace:
tun0: bpf attached
tun1: bpf attached
tun2: bpf attached
tun3: bpf attached
tun4: bpf attached
splash: image decoder found: logo_saver
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Request Requeued
(da0:ncr0:0:0:0): Retrying Command
(da0:ncr0:0:0:0): Queue Full
(da0:ncr0:0:0:0): tagged openings now 8
(da0:ncr0:0:0:0): Retrying Command
ed0: promiscuous mode enabled
drm0: <ATI Radeon QD R100> port 0xc000-0xc0ff mem 0xed000000-0xed00ffff,0xe0000000-0xe7ffffff irq 11 at device 0.0 on pci1
info: [drm] AGP at 0xe8000000 64MB
info: [drm] Initialized radeon 1.9.0 20020828 on minor 0
drm0: [MPSAFE]
--envbJBWh7q8WU6mo--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030929170823.GA14806>