Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 02 Jan 2013 15:25:14 -0800
From:      Manfred Antar <null@pozo.com>
To:        Gleb Smirnoff <glebius@FreeBSD.org>
Cc:        freebsd-current@freebsd.org
Subject:   Re: loopback interface broken on current
Message-ID:  <201301022325.r02NPKEE076633@pozo.com>
In-Reply-To: <20130102201330.GC25661@glebius.int.ru>
References:  <201212271705.qBRH5VHU006208@pozo.com> <20130101102255.GA25661@FreeBSD.org> <201301011040.r01Ae37A043153@pozo.com> <20130101194803.GB25661@glebius.int.ru> <201301012042.r01Kgq6E001548@pozo.com> <20130102201330.GC25661@glebius.int.ru>

next in thread | previous in thread | raw e-mail | index | archive | help

>
>
>Ok, so this is my failure. :( Sorry. I will look at it as soon as
>I get to decent internet connection. Right now I am on very bad GPRS.
>
>Can you please show your rc.conf (the network related part)?
>
>
>-- 
>Totus tuus, Glebius.

Here you go:
/etc/hosts:
::1             localhost       localhost.pozo.com
127.0.0.1       localhost       localhost.pozo.com

/etc/rc.conf:
ifconfig_lo0="inet 127.0.0.1"           # default loopback device configuration.
ifconfig_bge0="inet 192.168.0.5         netmask 255.255.255.0"

defaultrouter="192.168.0.1"             # Set to default gateway

ipv6_network_interfaces="auto"          # List of IPv6 network interfaces
                                                        # (or "auto" or "none").
ipv6_activate_all_interfaces="NO"       # If NO, interfaces which have no
ipv6_defaultrouter="NO"         # Set to IPv6 default gateway (or NO).
ipv6_static_routes=""                   # Set to static route list (or leave empty).
#ipv6_static_routes="xxx"               # An example to set fec0:0000:0000:0006::/64
                                                        #  route toward loopback interface.
#ipv6_route_xxx="fec0:0000:0000:0006:: -prefixlen 64 ::1"
ipv6_gateway_enable="NO"                # Set to YES if this host will be a gateway.
ipv6_cpe_wanif="NO"                             # Set to the upstram interface name if this
                                                        # node will work as a router to forward IPv6
                                                        # packets not explicitly addressed to itself.
ipv6_privacy="NO"                       # Use privacy address on RA-receiving IFs
                                                        # (RFC 4941)

route6d_enable="NO"                     # Set to YES to enable an IPv6 routing daemon.
route6d_program="/usr/sbin/route6d"     # Name of IPv6 routing daemon.
route6d_flags=""                        # Flags to IPv6 routing daemon.
#route6d_flags="-l"                     # Example for route6d with only IPv6 site local
                                                        # addrs.
#route6d_flags="-q"                             # If you want to run a routing daemon on an end
                                                        # node, you should stop advertisement.
#ipv6_network_interfaces="ed0 ep0"      # Examples for router
                                                        # or static configuration for end node.
                                                        # Choose correct prefix value.
#ipv6_prefix_ed0="fec0:0000:0000:0001 fec0:0000:0000:0002"  # Examples for rtr.
#ipv6_prefix_ep0="fec0:0000:0000:0003 fec0:0000:0000:0004"  # Examples for rtr.
ipv6_default_interface="NO"                     # Default output interface for scoped addrs.
                                                        # This works only with
                                                        # ipv6_gateway_enable="NO".

That pretty much it, nothing special
I haven't made any changes to it in over 2 years.

The only thing about 1 year ago I enabled:
### Network link/usability verification options
netwait_enable="YES"                    # Enable rc.d/netwait (or NO)
netwait_ip="192.168.0.1"                # IP addresses to be pinged by netwait. 


-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201301022325.r02NPKEE076633>