Date: Fri, 20 Oct 2006 14:36:35 +0200 From: Joel Dahl <joel@FreeBSD.org> To: acpi@FreeBSD.org Subject: HP NX7400 - ACPI problems Message-ID: <1161347795.671.14.camel@localhost>
next in thread | raw e-mail | index | archive | help
--=-STXYCKdOyAjC0TaJ1LZW Content-Type: text/plain Content-Transfer-Encoding: 7bit A few notes on running the latest CURRENT (plain GENERIC) on a HP NX7400 laptop, maybe someone can help me solve these problems: # 1 The following (somewhat annoying) message is repeated on the console all the time: acpi_tz0: _CRT value is absurd, ignored (256.0C) # 2 Sometimes, perhaps one out of ten, the battery isn't detected, so "acpiconf -i batt" gives me: Design capacity: 0 mWh Last full capacity: 0 mWh Technology: primary (non-rechargable) Design voltage: 0 mWh Capacity (warn): 0 mWh Capacity (low): 0 mWh Low/warn granularity: 0 mWh Warn/full granularity: 0 mWh Model number: Serial number: Type: OEM info: State: not present It should look like this (which it also usually does): Design capacity: 3915 mAh Last full capacity: 3915 mAh Technology: secondary (rechargable) Design voltage: 10800 mV Capacity (warn): 196 mAh Capacity (low): 40 mAh Low/warn granularity: 100 mAh Warn/full granularity: 100 mAh Model number: Primary Serial number: 02710 2006/05/10 Type: LIon OEM info: Hewlett-Packard State: high Remaining capacity 100% Remaining time unknown Present rate 0 mA Voltage 16626 mV # 3 Battery time in FreeBSD is bad compared to Windows. I can usually run this laptop on battery for 3,5 hours while in Windows, but the battery only lasts for 2 hours in FreeBSD. Can this be tweaked somehow? # 4 I've seen an ACPI-related panic (reported on current@) during boot. Only happened twice so far though. For reference: http://people.freebsd.org/~joel/panics/panic001.jpg I've also attached a verbose dmesg in case someone wants it. -- Joel --=-STXYCKdOyAjC0TaJ1LZW Content-Disposition: attachment; filename=dmesg.txt Content-Type: text/plain; name=dmesg.txt; charset=us-ascii Content-Transfer-Encoding: 7bit Copyright (c) 1992-2006 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-CURRENT #0: Fri Oct 20 09:45:22 CEST 2006 joel@jesus.automatvapen.se:/usr/obj/usr/src/sys/GENERIC WARNING: WITNESS option enabled, expect reduced performance. Using 64 colors for the VM-PQ tuning (2048, 8) Preloaded elf kernel "/boot/kernel/kernel" at 0xc0c44000. Preloaded elf module "/boot/kernel/snd_hda.ko" at 0xc0c441ec. Preloaded elf module "/boot/kernel/sound.ko" at 0xc0c44298. Preloaded elf module "/boot/kernel/atapicam.ko" at 0xc0c44344. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0c443f4. Table 'FACP' at 0x1f7e5600 Table 'APIC' at 0x1f7e56c0 MADT: Found table at 0x1f7e56c0 APIC: Using the MADT enumerator. MADT: Found CPU APIC ID 0 ACPI ID 1: enabled SMP: Added CPU 0 (AP) MADT: Found CPU APIC ID 1 ACPI ID 2: enabled SMP: Added CPU 1 (AP) INTR: Adding local APIC 0 as a target ACPI APIC Table: <HP 30A2 > Calibrating clock(s) ... i8254 clock: 1193178 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 1662513730 Hz CPU: Genuine Intel(R) CPU T2300 @ 1.66GHz (1662.51-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6e8 Stepping = 8 Features=0xbfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0xc189<SSE3,MON,EST,TM2,XTPR,<b15>> AMD Features=0x100000<NX> Cores per package: 2 Instruction TLB: 4 KB Pages, 4-way set associative, 128 entries Data TLB: 4 KB Pages, 4-way set associative, 128 entries Instruction TLB: 4 MB pages, fully associative, 2 entries 2nd-level cache: 2-MB, 8-way set associative, 64-byte line size 1st-level instruction cache: 32 KB, 8-way set associative, 64 byte line size Data TLB: 4 MB Pages, 4-way set associative, 8 entries 1st-level data cache: 32 KB, 8-way set associative, 64 byte line size L2 cache: 2048 kbytes, 8-way associative, 64 bytes/line real memory = 528285696 (503 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000001028000 - 0x000000001eeb0fff, 501780480 bytes (122505 pages) avail memory = 503099392 (479 MB) INTR: Adding local APIC 1 as a target FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 bios32: Found BIOS32 Service Directory header at 0xc00fa000 bios32: Entry = 0xf0000 (c00f0000) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0x322 pnpbios: Found PnP BIOS data at 0xc00f59a0 pnpbios: Entry = f0000:59ce Rev = 1.0 pnpbios: Event flag at f59c6 pnpbios: OEM ID a2303c10 Other BIOS signatures found: APIC: CPU 0 has ACPI ID 1 APIC: CPU 1 has ACPI ID 2 MADT: Found IO APIC ID 1, Interrupt 0 at 0xfec00000 ioapic0: Changing APIC ID to 1 ioapic0: Routing external 8259A's -> intpin 0 ioapic0: intpin 0 -> ExtINT (edge, high) ioapic0: intpin 1 -> ISA IRQ 1 (edge, high) ioapic0: intpin 2 -> ISA IRQ 2 (edge, high) ioapic0: intpin 3 -> ISA IRQ 3 (edge, high) ioapic0: intpin 4 -> ISA IRQ 4 (edge, high) ioapic0: intpin 5 -> ISA IRQ 5 (edge, high) ioapic0: intpin 6 -> ISA IRQ 6 (edge, high) ioapic0: intpin 7 -> ISA IRQ 7 (edge, high) ioapic0: intpin 8 -> ISA IRQ 8 (edge, high) ioapic0: intpin 9 -> ISA IRQ 9 (edge, high) ioapic0: intpin 10 -> ISA IRQ 10 (edge, high) ioapic0: intpin 11 -> ISA IRQ 11 (edge, high) ioapic0: intpin 12 -> ISA IRQ 12 (edge, high) ioapic0: intpin 13 -> ISA IRQ 13 (edge, high) ioapic0: intpin 14 -> ISA IRQ 14 (edge, high) ioapic0: intpin 15 -> ISA IRQ 15 (edge, high) ioapic0: intpin 16 -> PCI IRQ 16 (level, low) ioapic0: intpin 17 -> PCI IRQ 17 (level, low) ioapic0: intpin 18 -> PCI IRQ 18 (level, low) ioapic0: intpin 19 -> PCI IRQ 19 (level, low) ioapic0: intpin 20 -> PCI IRQ 20 (level, low) ioapic0: intpin 21 -> PCI IRQ 21 (level, low) ioapic0: intpin 22 -> PCI IRQ 22 (level, low) ioapic0: intpin 23 -> PCI IRQ 23 (level, low) MADT: Interrupt override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: high MADT: Interrupt override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: high lapic0: Routing NMI -> LINT1 lapic0: LINT1 trigger: edge lapic0: LINT1 polarity: high lapic1: Routing NMI -> LINT1 lapic1: LINT1 trigger: edge lapic1: LINT1 polarity: high ioapic0 <Version 2.0> irqs 0-23 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00000200 err: 0x00010000 pcm: 0x00010000 wlan: <802.11 Link Layer> ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> random: <entropy source, Software, Yarrow> nfslock: pseudo-device io: <I/O> kbd: new array size 4 kbd1 at kbdmux0 mem: <memory> Pentium Pro MTRR support enabled null: <null device, zero device> ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) rr232x: RocketRAID 232x controller driver v1.02 (Oct 20 2006 09:45:05) npx0: INT 16 interface acpi0: <HP 30A2> on motherboard ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x8000fa20 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=27a08086) pcibios: BIOS version 2.10 acpi_bus_number: root bus has no _BBN, assuming 0 acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR AcpiOsDerivePciId: bus 0 dev 0 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR AcpiOsDerivePciId: bus 2 dev 6 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi0: Power Button (fixed) acpi0: wakeup code va 0xcc8a5000 pa 0x9d000 ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 acpi_ec0: <Embedded Controller: GPE 0x16> port 0x62,0x66 on acpi0 pci_link0: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 10 11 pci_link0: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 10 11 pci_link0: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link1: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 10 11 pci_link1: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 10 11 pci_link1: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link2: Links after initial probe: Index IRQ Rtd Ref IRQs 0 11 N 0 10 11 pci_link2: Links after initial validation: Index IRQ Rtd Ref IRQs 0 11 N 0 10 11 pci_link2: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link3: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 10 11 pci_link3: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 10 11 pci_link3: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link4: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 10 11 pci_link4: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 10 11 pci_link4: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link5: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link5: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link5: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link6: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link6: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link6: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 10 11 pci_link7: Links after initial probe: Index IRQ Rtd Ref IRQs 0 255 N 0 none pci_link7: Links after initial validation: Index IRQ Rtd Ref IRQs 0 255 N 0 none pci_link7: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 none cpu0: <ACPI CPU> on acpi0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_throttle0: P_CNT from P_BLK 0x1010 cpu1: <ACPI CPU> on acpi0 acpi_throttle1: <ACPI CPU Throttling> on cpu1 acpi_throttle1: failed to attach P_CNT device_attach: acpi_throttle1 attach returned 6 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x8086, dev=0x27a0, revid=0x03 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x27a2, revid=0x03 bus=0, slot=2, func=0 class=03-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0003, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 MSI supports 1 message map[10]: type 1, range 32, base f4400000, size 19, enabled map[14]: type 4, range 32, base 00004000, size 3, enabled map[18]: type 3, range 32, base e0000000, size 28, enabled map[1c]: type 1, range 32, base f4480000, size 18, enabled pcib0: matched entry for 0.2.INTA pcib0: slot 2 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x27a6, revid=0x03 bus=0, slot=2, func=1 class=03-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base f4500000, size 19, enabled found-> vendor=0x8086, dev=0x27d8, revid=0x01 bus=0, slot=27, func=0 class=04-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type 1, range 64, base f4580000, size 14, enabled pcib0: matched entry for 0.27.INTA pcib0: slot 27 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x27d0, revid=0x01 bus=0, slot=28, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 pcib0: matched entry for 0.28.INTA pcib0: slot 28 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x27d2, revid=0x01 bus=0, slot=28, func=1 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 pcib0: matched entry for 0.28.INTB pcib0: slot 28 INTB hardwired to IRQ 17 found-> vendor=0x8086, dev=0x27d6, revid=0x01 bus=0, slot=28, func=3 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) intpin=d, irq=10 pcib0: matched entry for 0.28.INTD pcib0: slot 28 INTD hardwired to IRQ 19 found-> vendor=0x8086, dev=0x27c8, revid=0x01 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 map[20]: type 4, range 32, base 00004020, size 5, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 20 found-> vendor=0x8086, dev=0x27c9, revid=0x01 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 map[20]: type 4, range 32, base 00004040, size 5, enabled pcib0: matched entry for 0.29.INTB pcib0: slot 29 INTB hardwired to IRQ 17 found-> vendor=0x8086, dev=0x27ca, revid=0x01 bus=0, slot=29, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=11 map[20]: type 4, range 32, base 00004060, size 5, enabled pcib0: matched entry for 0.29.INTC pcib0: slot 29 INTC hardwired to IRQ 18 found-> vendor=0x8086, dev=0x27cb, revid=0x01 bus=0, slot=29, func=3 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=10 map[20]: type 4, range 32, base 00004080, size 5, enabled pcib0: matched entry for 0.29.INTD pcib0: slot 29 INTD hardwired to IRQ 19 found-> vendor=0x8086, dev=0x27cc, revid=0x01 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base f4584000, size 10, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 20 found-> vendor=0x8086, dev=0x2448, revid=0xe1 bus=0, slot=30, func=0 class=06-04-01, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x27b9, revid=0x01 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0107, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x27df, revid=0x01 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 map[20]: type 4, range 32, base 000040a0, size 4, enabled pcib0: matched entry for 0.31.INTA pcib0: slot 31 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x27c5, revid=0x01 bus=0, slot=31, func=2 class=01-06-01, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 powerspec 2 supports D0 D3 current D0 MSI supports 1 message map[10]: type 4, range 32, base 000013f0, size 3, enabled map[14]: type 4, range 32, base 000015f4, size 2, enabled map[18]: type 4, range 32, base 00001370, size 3, enabled map[1c]: type 4, range 32, base 00001574, size 2, enabled map[20]: type 4, range 32, base 000040d0, size 4, enabled map[24]: type 1, range 32, base f4585000, size 10, enabled pcib0: matched entry for 0.31.INTB pcib0: slot 31 INTB hardwired to IRQ 17 vgapci0: <VGA-compatible display> port 0x4000-0x4007 mem 0xf4400000-0xf447ffff,0xe0000000-0xefffffff,0xf4480000-0xf44bffff irq 16 at device 2.0 on pci0 agp0: <Intel 82945GM (945GM GMCH) SVGA controller> on vgapci0 vgapci0: Reserved 0x80000 bytes for rid 0x10 type 3 at 0xf4400000 vgapci0: Reserved 0x80000 bytes for rid 0x10 type 3 at 0xf4400000 vgapci0: Reserved 0x40000 bytes for rid 0x1c type 3 at 0xf4480000 vgapci0: Reserved 0x10000000 bytes for rid 0x18 type 3 at 0xe0000000 agp0: detected 7932k stolen memory agp0: aperture size is 256M vgapci1: <VGA-compatible display> mem 0xf4500000-0xf457ffff at device 2.1 on pci0 pcm0: <Intel 82801G High Definition Audio Controller> mem 0xf4580000-0xf4583fff irq 16 at device 27.0 on pci0 pcm0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xf4580000 ioapic0: routing intpin 16 (PCI IRQ 16) to vector 49 pcm0: [MPSAFE] pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 pcib1: secondary bus 8 pcib1: subordinate bus 8 pcib1: I/O decode 0xf000-0xfff pcib1: memory decode 0xfff00000-0xfffff pcib1: prefetched decode 0xfff00000-0xfffff pci8: <ACPI PCI bus> on pcib1 pci8: physical bus=8 pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0 pcib2: secondary bus 16 pcib2: subordinate bus 16 pcib2: I/O decode 0xf000-0xfff pcib2: memory decode 0xf4000000-0xf40fffff pcib2: prefetched decode 0xfff00000-0xfffff pci16: <ACPI PCI bus> on pcib2 pci16: physical bus=16 found-> vendor=0x8086, dev=0x4222, revid=0x02 bus=16, slot=0, func=0 class=02-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type 1, range 32, base f4000000, size 12, enabled pcib2: (null) requested memory range 0xf4000000-0xf4000fff: good pcib2: matched entry for 16.0.INTA pcib2: slot 0 INTA hardwired to IRQ 17 pci16: <network> at device 0.0 (no driver attached) pcib3: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0 pcib3: secondary bus 32 pcib3: subordinate bus 32 pcib3: I/O decode 0x2000-0x3fff pcib3: memory decode 0xf0000000-0xf3ffffff pcib3: prefetched decode 0xfff00000-0xfffff pci32: <ACPI PCI bus> on pcib3 pci32: physical bus=32 uhci0: <UHCI (generic) USB controller> port 0x4020-0x403f irq 20 at device 29.0 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x4020 ioapic0: routing intpin 20 (PCI IRQ 20) to vector 50 uhci0: [GIANT-LOCKED] usb0: <UHCI (generic) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: <UHCI (generic) USB controller> port 0x4040-0x405f irq 17 at device 29.1 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x4040 ioapic0: routing intpin 17 (PCI IRQ 17) to vector 51 uhci1: [GIANT-LOCKED] usb1: <UHCI (generic) USB controller> on uhci1 usb1: USB revision 1.0 uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 2 ports with 2 removable, self powered uhci2: <UHCI (generic) USB controller> port 0x4060-0x407f irq 18 at device 29.2 on pci0 uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x4060 ioapic0: routing intpin 18 (PCI IRQ 18) to vector 52 uhci2: [GIANT-LOCKED] usb2: <UHCI (generic) USB controller> on uhci2 usb2: USB revision 1.0 uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2 uhub2: 2 ports with 2 removable, self powered uhci3: <UHCI (generic) USB controller> port 0x4080-0x409f irq 19 at device 29.3 on pci0 uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x4080 ioapic0: routing intpin 19 (PCI IRQ 19) to vector 53 uhci3: [GIANT-LOCKED] usb3: <UHCI (generic) USB controller> on uhci3 usb3: USB revision 1.0 uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3 uhub3: 2 ports with 2 removable, self powered ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xf4584000-0xf45843ff irq 20 at device 29.7 on pci0 ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xf4584000 ehci0: [GIANT-LOCKED] usb4: EHCI version 1.0 usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0 usb4: USB revision 2.0 uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4 uhub4: 8 ports with 8 removable, self powered pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib4: secondary bus 2 pcib4: subordinate bus 3 pcib4: I/O decode 0xf000-0xfff pcib4: memory decode 0xf4100000-0xf43fffff pcib4: prefetched decode 0xfff00000-0xfffff pcib4: Subtractively decoded bridge. pci2: <ACPI PCI bus> on pcib4 pci2: physical bus=2 found-> vendor=0x104c, dev=0x8039, revid=0x00 bus=2, slot=6, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0xc4 (49000 ns), maxlat=0x03 (750 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base f4100000, size 12, enabled pcib4: (null) requested memory range 0xf4100000-0xf4100fff: good pcib4: matched entry for 2.6.INTA pcib4: slot 6 INTA hardwired to IRQ 18 found-> vendor=0x104c, dev=0x803a, revid=0x00 bus=2, slot=6, func=1 class=0c-00-10, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0210, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns) intpin=b, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base f4101000, size 11, enabled pcib4: (null) requested memory range 0xf4101000-0xf41017ff: good map[14]: type 1, range 32, base f4104000, size 14, enabled pcib4: (null) requested memory range 0xf4104000-0xf4107fff: good pcib4: matched entry for 2.6.INTB pcib4: slot 6 INTB hardwired to IRQ 19 found-> vendor=0x14e4, dev=0x170c, revid=0x02 bus=2, slot=14, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base f4108000, size 13, enabled pcib4: (null) requested memory range 0xf4108000-0xf4109fff: good pcib4: matched entry for 2.14.INTA pcib4: slot 14 INTA hardwired to IRQ 16 cbb0: <PCI-CardBus Bridge> mem 0xf4100000-0xf4100fff irq 18 at device 6.0 on pci2 cbb0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf4100000 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 cbb0: [MPSAFE] cbb0: PCI Configuration space: 0x00: 0x8039104c 0x02100007 0x06070000 0x00824010 0x10: 0xf4100000 0x020000a0 0x20030302 0xfffff000 0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 0x30: 0x00000000 0xfffffffc 0x00000000 0x07440112 0x40: 0x30a2103c 0x00000001 0x00000000 0x00000000 0x50: 0x00000000 0x00000000 0x00000000 0x00000000 0x60: 0x00000000 0x00000000 0x00000000 0x00000000 0x70: 0x00000000 0x00000000 0x00000000 0x00000000 0x80: 0x08441060 0x01a30019 0x00170000 0x01011b22 0x90: 0x406402c0 0x00000000 0x00000000 0x00000000 0xa0: 0xfe120001 0x00c00000 0x00000000 0x00000000 0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 0xf0: 0xb7512925 0x0e019467 0x00000000 0x00000000 fwohci0: vendor=104c, dev=803a fwohci0: vendor=104c, dev=803a fwohci0: <1394 Open Host Controller Interface> mem 0xf4101000-0xf41017ff,0xf4104000-0xf4107fff irq 19 at device 6.1 on pci2 fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xf4101000 fwohci0: [MPSAFE] fwohci0: OHCI version 1.10 (ROM=0) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:02:3f:99:29:c1:29:0c fwohci0: Phy 1394a available S400, 3 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:02:3f:c1:29:0c fwe0: bpf attached fwe0: Ethernet address: 02:02:3f:c1:29:0c fwe0: if_start running deferred for Giant sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwohci0: Initiate bus reset fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) bfe0: <Broadcom BCM4401-B0 Fast Ethernet> mem 0xf4108000-0xf4109fff irq 16 at device 14.0 on pci2 bfe0: Reserved 0x2000 bytes for rid 0x10 type 3 at 0xf4108000 miibus0: <MII bus> on bfe0 bmtphy0: <BCM4401 10/100baseTX PHY> on miibus0 bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto bfe0: bpf attached bfe0: Ethernet address: 00:15:60:c3:2d:2a bfe0: [MPSAFE] isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x40a0-0x40af irq 16 at device 31.1 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x40a0 ata0: <ATA channel 0> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb ata0: stat1=0x00 err=0x00 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ioapic0: routing intpin 14 (ISA IRQ 14) to vector 54 ata0: [MPSAFE] ata1: <ATA channel 1> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=00 ostat0=ff ostat1=ff ioapic0: routing intpin 15 (ISA IRQ 15) to vector 55 ata1: [MPSAFE] atapci1: <Intel ICH7M SATA300 controller> port 0x13f0-0x13f7,0x15f4-0x15f7,0x1370-0x1377,0x1574-0x1577,0x40d0-0x40df mem 0xf4585000-0xf45853ff irq 17 at device 31.2 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x40d0 atapci1: [MPSAFE] atapci1: Reserved 0x400 bytes for rid 0x24 type 3 at 0xf4585000 atapci1: AHCI Version 01.10 controller with 4 ports detected ata2: <ATA channel 0> on atapci1 ata2: SATA connect ready time=0ms ata2: sata_connect devices=0x1<ATA_MASTER> ata2: [MPSAFE] ata3: <ATA channel 1> on atapci1 ata3: SATA connect status=00000000 ata3: [MPSAFE] ata4: <ATA channel 2> on atapci1 ata4: SATA connect status=00000000 ata4: [MPSAFE] ata5: <ATA channel 3> on atapci1 ata5: SATA connect status=00000000 ata5: [MPSAFE] battery0: <ACPI Control Method Battery> on acpi0 battery1: <ACPI Control Method Battery> on acpi0 acpi_acad0: <AC Adapter> on acpi0 acpi_button0: <Sleep Button> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 acpi_tz0: _CRT value is absurd, ignored (256.0C) acpi_tz1: <Thermal Zone> on acpi0 acpi_tz2: <Thermal Zone> on acpi0 acpi_tz3: <Thermal Zone> on acpi0 acpi_tz4: <Thermal Zone> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 ioapic0: routing intpin 1 (ISA IRQ 1) to vector 56 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ psmcpnp0: <PS/2 mouse port> irq 12 on acpi0 psm0: current command byte:0065 psm0: <PS/2 Mouse> irq 12 on atkbdc0 ioapic0: routing intpin 12 (ISA IRQ 12) to vector 57 psm0: [GIANT-LOCKED] psm0: model IntelliMouse, device ID 3-00, 3 buttons psm0: config:00000000, flags:00000008, packet size:4 psm0: syncmask:08, syncbits:00 unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff ex_isa_identify() ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it pnp_identify: Trying Read_Port at 203 pnp_identify: Trying Read_Port at 243 pnp_identify: Trying Read_Port at 283 pnp_identify: Trying Read_Port at 2c3 pnp_identify: Trying Read_Port at 303 pnp_identify: Trying Read_Port at 343 pnp_identify: Trying Read_Port at 383 pnp_identify: Trying Read_Port at 3c3 PNP Identify complete sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff pnpid ORM0000 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) ppc0: parallel port found at 0x378 ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ioapic0: routing intpin 7 (ISA IRQ 7) to vector 58 ppc0: [GIANT-LOCKED] sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0x4e81 0x4e81 0x4e81 0x4e81 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0x4e81 0x4e81 0x4e81 0x4e81 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding ioapic0: routing intpin 4 (ISA IRQ 4) to vector 59 sio0: [FAST] sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0x4e81 0x4e81 0x4e81 0x4e81 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered lapic: Divisor 2, Frequency 83125691 hz Timecounter "TSC" frequency 1662513730 Hz quality -100 Timecounters tick every 1.000 msec lo0: bpf attached rr232x: no controller detected. acpi_tz0: _AC3: temperature 60.0 >= setpoint 50.0 acpi_tz0: _AC2: temperature 60.0 >= setpoint 60.0 acpi_tz0: switched from NONE to _AC2: 60.0C battery0: battery initialization start battery1: battery initialization start ata0-master: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=40 wire acd0: setting PIO4 on ICH7 chip acd0: <HL-DT-ST DVDRAM GSA-4082N/CQ04> DVDR drive at ata0 as master acd0: read 4134KB/s (4134KB/s) write 4134KB/s (4134KB/s), 2048KB buffer, PIO4 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc acpi_tz0: _AC3: temperature 60.0 >= setpoint 50.0 acpi_tz0: _CRT value is absurd, ignored (256.0C) acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire acpi_acad0: acline initialization start acpi_acad0: On Line acpi_acad0: acline initialization done, tried 1 times acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 ad4: 76319MB <FUJITSU MHV2080BH 892C> at ata2-master SATA150 ad4: 156301488 sectors [165398C/15H/63S] 16 sectors/interrupt 1 depth queue GEOM: new disk ad4 battery0: battery initialization done, tried 1 times ad4: Intel check1 failed ad4: Adaptec check1 failed ad4: LSI (v3) check1 failed ad4: LSI (v2) check1 failed ad4: FreeBSD check1 failed pcm0: HDA_DEBUG: HDA Config: on=0x00000000 off=0x00000000 pcm0: HDA_DEBUG: Starting CORB Engine... pcm0: HDA_DEBUG: Starting RIRB Engine... pcm0: HDA_DEBUG: Enabling controller interrupt... pcm0: HDA_DEBUG: Scanning HDA codecs... pcm0: HDA_DEBUG: Probing codec: 0 pcm0: HDA_DEBUG: startnode=1 endnode=2 pcm0: HDA_DEBUG: Found AFG nid=1 [startnode=1 endnode=2] pcm0: HDA_DEBUG: Parsing AFG nid=1 cad=0 pcm0: Vendor: 0x000011d4 pcm0: Device: 0x00001981 pcm0: Revision: 0x00000002 pcm0: Stepping: 0x00000000 pcm0: PCI Subvendor: 0x30a2103c pcm0: Nodes: start=2 endnode=32 total=30 pcm0: HDA_DEBUG: Parsing Ctls... pcm0: HDA_DEBUG: Parsing vendor patch... pcm0: HDA_DEBUG: Building AFG tree... pcm0: HDA_DEBUG: HWiP: HDA Widget Parser - Revision 1 pcm0: HDA_DEBUG: HWiP: Found 2 DAC path using HDA_PARSE_MIXER strategy. pcm0: HDA_DEBUG: AFG commit... pcm0: HDA_DEBUG: Ctls commit... pcm0: [ 1] Ctl nid=5 Bind to NONE pcm0: [ 2] Ctl nid=5 Bind to NONE pcm0: [ 3] Ctl nid=6 Bind to NONE pcm0: [ 4] Ctl nid=7 DISABLED pcm0: [ 5] Ctl nid=8 Bind to NONE pcm0: [ 6] Ctl nid=9 Bind to NONE pcm0: [ 7] Ctl nid=9 Bind to NONE pcm0: [13] Ctl nid=24 Bind to NONE pcm0: [14] Ctl nid=24 Bind to NONE pcm0: [15] Ctl nid=26 Bind to NONE pcm0: [16] Ctl nid=27 Bind to NONE pcm0: [18] Ctl nid=29 Bind to NONE pcm0: [19] Ctl nid=30 Bind to NONE pcm0: [20] Ctl nid=31 Bind to NONE pcm0: HDA_DEBUG: PCMDIR_PLAY setup... pcm0: HDA_DEBUG: PCMDIR_REC setup... pcm0: HDA_DEBUG: OSS mixer initialization... pcm0: HDA_DEBUG: Pin sense: nid=6 res=0x0000ffe4 pcm0: HDA_DEBUG: Enabling headphone/speaker audio routing switching: pcm0: HDA_DEBUG: index=1 nid=6 pci_subvendor=0x30a2103c codec=0x11d41981 pcm0: Mixer "vol": pcm0: Mixer "pcm": pcm0: Mixer "speaker": pcm0: Mixer "line": pcm0: Mixer "mic": pcm0: Mixer "rec": pcm0: Mixer "ogain": pcm0: HDA_DEBUG: Registering PCM channels... pcm0: sndbuf_setmap 1e8c9000, 4000; 0xd4a95000 -> 1e8c9000 pcm0: sndbuf_setmap 1e8af000, 4000; 0xd4a99000 -> 1e8af000 pcm0: <HDA Codec: Analog Device AD1981HD> pcm0: <HDA Codec ID: 0x11d41981> pcm0: <HDA Driver Revision: 20061017_0033> pcm0: pcm0: HDA config/quirks: fixedrate forcestereo pcm0: pcm0: +-------------------+ pcm0: | DUMPING HDA NODES | pcm0: +-------------------+ pcm0: pcm0: Default Parameter pcm0: ----------------- pcm0: Stream cap: 0x00000001 pcm0: Format: PCM pcm0: PCM cap: 0x000e007f pcm0: PCM size: 16 20 24 pcm0: PCM rate: 44 48 88 96 176 192 pcm0: IN amp: 0x00270300 pcm0: OUT amp: 0x80053f3d pcm0: pcm0: nid: 2 [DIGITAL] [DISABLED] pcm0: name: audio output pcm0: widget_cap: 0x00030311 pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000000 pcm0: Stream cap: 0x00000005 pcm0: Format: AC3 PCM pcm0: PCM cap: 0x00020060 pcm0: PCM size: 16 pcm0: PCM rate: 44 48 pcm0: connections: 2 pcm0: | pcm0: + <- nid=1 [GHOST!] [UNKNOWN] pcm0: | pcm0: + <- nid=4 [audio input] pcm0: pcm0: nid: 3 [ANALOG] pcm0: name: audio output pcm0: widget_cap: 0x00000441 pcm0: Parse flags: 0x00000001 pcm0: Ctl flags: 0x00000011 pcm0: Stream cap: 0x00000001 pcm0: Format: PCM pcm0: PCM cap: 0x000e007f pcm0: PCM size: 16 20 24 pcm0: PCM rate: 44 48 88 96 176 192 pcm0: connections: 0 pcm0: pcm0: nid: 4 [ANALOG] pcm0: name: audio input pcm0: widget_cap: 0x00100511 pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000800 pcm0: Stream cap: 0x00000001 pcm0: Format: PCM pcm0: PCM cap: 0x0006007f pcm0: PCM size: 16 20 pcm0: PCM rate: 44 48 88 96 176 192 pcm0: connections: 1 pcm0: | pcm0: + <- nid=21 [audio selector] pcm0: pcm0: nid: 5 [ANALOG] pcm0: name: pin: line out (jack) pcm0: widget_cap: 0x00400187 pcm0: Parse flags: 0x00000001 pcm0: Ctl flags: 0x00000000 pcm0: Pin cap: 0x0001173f pcm0: ISC TRQD HP OUT IN EAPD : UNSOL pcm0: Pin config: 0x01014010 pcm0: Pin control: 0x00000040 OUT pcm0: EAPD: 0x00000002 pcm0: Output amp: 0x80053f3d pcm0: mute=1 step=63 size=5 offset=61 pcm0: Input amp: 0x00270300 pcm0: mute=0 step=3 size=39 offset=0 pcm0: connections: 2 pcm0: | pcm0: + <- nid=3 [audio output] pcm0: | pcm0: + <- nid=14 [audio mixer] (selected) pcm0: pcm0: nid: 6 [ANALOG] pcm0: name: pin: headphones out (jack) pcm0: widget_cap: 0x00400185 pcm0: Parse flags: 0x00000001 pcm0: Ctl flags: 0x00000000 pcm0: Pin cap: 0x0000001f pcm0: ISC TRQD HP OUT : UNSOL pcm0: Pin config: 0x0221401f pcm0: Pin control: 0x000000c0 HP OUT pcm0: Output amp: 0x80053f3d pcm0: mute=1 step=63 size=5 offset=61 pcm0: connections: 2 pcm0: | pcm0: + <- nid=3 [audio output] pcm0: | pcm0: + <- nid=14 [audio mixer] (selected) pcm0: pcm0: nid: 7 [ANALOG] [DISABLED] pcm0: name: pin: line out (none) pcm0: widget_cap: 0x00400104 pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000000 pcm0: Pin cap: 0x00000010 pcm0: OUT pcm0: Pin config: 0x50070030 pcm0: Pin control: 0x00000040 OUT pcm0: Output amp: 0x80053f3d pcm0: mute=1 step=63 size=5 offset=61 pcm0: connections: 1 pcm0: | pcm0: + <- nid=15 [audio mixer] pcm0: pcm0: nid: 8 [ANALOG] pcm0: name: pin: Mic in (jack) pcm0: widget_cap: 0x00400083 pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000081 pcm0: Pin cap: 0x00001727 pcm0: ISC TRQD IN : UNSOL pcm0: Pin config: 0x02a19040 pcm0: Pin control: 0x00000020 IN pcm0: Input amp: 0x00270300 pcm0: mute=0 step=3 size=39 offset=0 pcm0: connections: 0 pcm0: pcm0: nid: 9 [ANALOG] pcm0: name: pin: line in (jack) pcm0: widget_cap: 0x00400187 pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000041 pcm0: Pin cap: 0x00001737 pcm0: ISC TRQD OUT IN : UNSOL pcm0: Pin config: 0x01813041 pcm0: Pin control: 0x00000020 IN pcm0: Output amp: 0x80053f3d pcm0: mute=1 step=63 size=5 offset=61 pcm0: Input amp: 0x00270300 pcm0: mute=0 step=3 size=39 offset=0 pcm0: connections: 2 pcm0: | pcm0: + <- nid=3 [audio output] (selected) pcm0: | pcm0: + <- nid=14 [audio mixer] pcm0: pcm0: nid: 10 [DIGITAL] [DISABLED] pcm0: name: pin: SPDIF out (none) pcm0: widget_cap: 0x00400301 pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000000 pcm0: Pin cap: 0x00000010 pcm0: OUT pcm0: Pin config: 0x41450020 pcm0: Pin control: 0x00000040 OUT pcm0: connections: 1 pcm0: | pcm0: + <- nid=2 [audio output] [DISABLED] pcm0: pcm0: nid: 11 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x00300101 pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000000 pcm0: connections: 6 pcm0: | pcm0: + <- nid=3 [audio output] pcm0: | pcm0: + <- nid=12 [audio mixer] pcm0: | pcm0: + <- nid=9 [pin: line in (jack)] pcm0: | pcm0: + <- nid=14 [audio mixer] (selected) pcm0: | pcm0: + <- nid=5 [pin: line out (jack)] pcm0: | pcm0: + <- nid=24 [pin: Mic in (jack)] pcm0: pcm0: nid: 12 [ANALOG] pcm0: name: audio mixer pcm0: widget_cap: 0x00200101 pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000000 pcm0: connections: 2 pcm0: | pcm0: + <- nid=30 [audio selector] pcm0: | pcm0: + <- nid=31 [audio selector] pcm0: pcm0: nid: 13 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010c pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000021 pcm0: Output amp: 0x800b0f0f pcm0: mute=1 step=15 size=11 offset=15 pcm0: connections: 2 pcm0: | pcm0: + <- nid=16 [beep widget] (selected) pcm0: | pcm0: + <- nid=22 [pin: other (fixed)] pcm0: pcm0: nid: 14 [ANALOG] pcm0: name: audio mixer pcm0: widget_cap: 0x00200101 pcm0: Parse flags: 0x00000003 pcm0: Ctl flags: 0x000000f1 pcm0: connections: 8 pcm0: | pcm0: + <- nid=13 [audio selector] pcm0: | pcm0: + <- nid=17 [audio selector] pcm0: | pcm0: + <- nid=18 [audio selector] pcm0: | pcm0: + <- nid=19 [audio selector] pcm0: | pcm0: + <- nid=26 [audio selector] pcm0: | pcm0: + <- nid=27 [audio selector] pcm0: | pcm0: + <- nid=28 [audio selector] pcm0: | pcm0: + <- nid=29 [audio selector] pcm0: pcm0: nid: 15 [ANALOG] pcm0: name: audio mixer pcm0: widget_cap: 0x00200100 pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000000 pcm0: connections: 1 pcm0: | pcm0: + <- nid=11 [audio selector] pcm0: pcm0: nid: 16 [ANALOG] pcm0: name: beep widget pcm0: widget_cap: 0x00700000 pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000021 pcm0: connections: 0 pcm0: pcm0: nid: 17 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010d pcm0: Parse flags: 0x00000001 pcm0: Ctl flags: 0x00000011 pcm0: Output amp: 0x80051f17 pcm0: mute=1 step=31 size=5 offset=23 pcm0: connections: 1 pcm0: | pcm0: + <- nid=3 [audio output] pcm0: pcm0: nid: 18 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010d pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000081 pcm0: Output amp: 0x80051f17 pcm0: mute=1 step=31 size=5 offset=23 pcm0: connections: 1 pcm0: | pcm0: + <- nid=8 [pin: Mic in (jack)] pcm0: pcm0: nid: 19 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010d pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000041 pcm0: Output amp: 0x80051f17 pcm0: mute=1 step=31 size=5 offset=23 pcm0: connections: 1 pcm0: | pcm0: + <- nid=9 [pin: line in (jack)] pcm0: pcm0: nid: 20 [ANALOG] pcm0: name: power widget pcm0: widget_cap: 0x00500500 pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000000 pcm0: connections: 6 pcm0: | pcm0: + <- nid=13 [audio selector] (selected) pcm0: | pcm0: + <- nid=14 [audio mixer] pcm0: | pcm0: + <- nid=144 [GHOST!] [UNKNOWN] pcm0: | pcm0: + <- nid=19 [audio selector] pcm0: | pcm0: + <- nid=154 [GHOST!] [UNKNOWN] pcm0: | pcm0: + <- nid=29 [audio selector] pcm0: pcm0: nid: 21 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010d pcm0: Parse flags: 0x00000006 pcm0: Ctl flags: 0x00000800 pcm0: Output amp: 0x80050f00 pcm0: mute=1 step=15 size=5 offset=0 pcm0: connections: 8 pcm0: | pcm0: + <- nid=12 [audio mixer] pcm0: | pcm0: + <- nid=9 [pin: line in (jack)] pcm0: | pcm0: + <- nid=14 [audio mixer] pcm0: | pcm0: + <- nid=15 [audio mixer] pcm0: | pcm0: + <- nid=25 [pin: CD (none)] [DISABLED] pcm0: | pcm0: + <- nid=5 [pin: line out (jack)] pcm0: | pcm0: + <- nid=24 [pin: Mic in (jack)] (selected) pcm0: | pcm0: + <- nid=23 [pin: AUX (none)] [DISABLED] pcm0: pcm0: nid: 22 [ANALOG] pcm0: name: pin: other (fixed) pcm0: widget_cap: 0x00400000 pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000000 pcm0: Pin cap: 0x00000020 pcm0: IN pcm0: Pin config: 0x90f30050 pcm0: Pin control: 0x00000000 pcm0: connections: 0 pcm0: pcm0: nid: 23 [ANALOG] [DISABLED] pcm0: name: pin: AUX (none) pcm0: widget_cap: 0x00400081 pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000000 pcm0: Pin cap: 0x00000027 pcm0: ISC TRQD IN : UNSOL pcm0: Pin config: 0x50930044 pcm0: Pin control: 0x00000020 IN pcm0: connections: 0 pcm0: pcm0: nid: 24 [ANALOG] pcm0: name: pin: Mic in (jack) pcm0: widget_cap: 0x00400187 pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000081 pcm0: Pin cap: 0x00001737 pcm0: ISC TRQD OUT IN : UNSOL pcm0: Pin config: 0x01a19043 pcm0: Pin control: 0x00000020 IN pcm0: Output amp: 0x80053f3d pcm0: mute=1 step=63 size=5 offset=61 pcm0: Input amp: 0x00270300 pcm0: mute=0 step=3 size=39 offset=0 pcm0: connections: 2 pcm0: | pcm0: + <- nid=3 [audio output] (selected) pcm0: | pcm0: + <- nid=14 [audio mixer] pcm0: pcm0: nid: 25 [ANALOG] [DISABLED] pcm0: name: pin: CD (none) pcm0: widget_cap: 0x00400001 pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000000 pcm0: Pin cap: 0x00000020 pcm0: IN pcm0: Pin config: 0x50330042 pcm0: Pin control: 0x00000020 IN pcm0: connections: 0 pcm0: pcm0: nid: 26 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010d pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000000 pcm0: Output amp: 0x80051f17 pcm0: mute=1 step=31 size=5 offset=23 pcm0: connections: 1 pcm0: | pcm0: + <- nid=5 [pin: line out (jack)] pcm0: pcm0: nid: 27 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010d pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000000 pcm0: Output amp: 0x80051f17 pcm0: mute=1 step=31 size=5 offset=23 pcm0: connections: 1 pcm0: | pcm0: + <- nid=23 [pin: AUX (none)] [DISABLED] pcm0: pcm0: nid: 28 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010d pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000081 pcm0: Output amp: 0x80051f17 pcm0: mute=1 step=31 size=5 offset=23 pcm0: connections: 1 pcm0: | pcm0: + <- nid=24 [pin: Mic in (jack)] pcm0: pcm0: nid: 29 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010d pcm0: Parse flags: 0x00000000 pcm0: Ctl flags: 0x00000000 pcm0: Output amp: 0x80051f17 pcm0: mute=1 step=31 size=5 offset=23 pcm0: connections: 1 pcm0: | pcm0: + <- nid=25 [pin: CD (none)] [DISABLED] pcm0: pcm0: nid: 30 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010d pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000000 pcm0: Output amp: 0x80000000 pcm0: mute=1 step=0 size=0 offset=0 pcm0: connections: 1 pcm0: | pcm0: + <- nid=8 [pin: Mic in (jack)] pcm0: pcm0: nid: 31 [ANALOG] pcm0: name: audio selector pcm0: widget_cap: 0x0030010d pcm0: Parse flags: 0x00000002 pcm0: Ctl flags: 0x00000000 pcm0: Output amp: 0x80000000 pcm0: mute=1 step=0 size=0 offset=0 pcm0: connections: 1 pcm0: | pcm0: + <- nid=24 [pin: Mic in (jack)] pcm0: pcm0: +------------------------+ pcm0: | DUMPING HDA AMPLIFIERS | pcm0: +------------------------+ pcm0: pcm0: 1: nid=5 dir=0x1 index=0 ossmask=0x00000000 ossdev=0 pcm0: 2: nid=5 dir=0x2 index=0 ossmask=0x00000000 ossdev=0 pcm0: 3: nid=6 dir=0x1 index=0 ossmask=0x00000000 ossdev=0 pcm0: 4: nid=7 dir=0x1 index=0 ossmask=0x00000000 ossdev=0 [DISABLED] pcm0: 5: nid=8 dir=0x2 index=0 ossmask=0x00000000 ossdev=0 pcm0: 6: nid=9 dir=0x1 index=0 ossmask=0x00000000 ossdev=0 pcm0: 7: nid=9 dir=0x2 index=0 ossmask=0x00000000 ossdev=0 pcm0: 8: nid=13 dir=0x1 index=0 ossmask=0x00000021 ossdev=5 pcm0: 9: nid=17 dir=0x1 index=0 ossmask=0x00000011 ossdev=4 pcm0: 10: nid=18 dir=0x1 index=0 ossmask=0x00000081 ossdev=7 pcm0: 11: nid=19 dir=0x1 index=0 ossmask=0x00000041 ossdev=6 pcm0: 12: nid=21 dir=0x1 index=0 ossmask=0x00000800 ossdev=0 pcm0: 13: nid=24 dir=0x1 index=0 ossmask=0x00000000 ossdev=0 pcm0: 14: nid=24 dir=0x2 index=0 ossmask=0x00000000 ossdev=0 pcm0: 15: nid=26 dir=0x1 index=0 ossmask=0x00000000 ossdev=0 pcm0: 16: nid=27 dir=0x1 index=0 ossmask=0x00000000 ossdev=0 pcm0: 17: nid=28 dir=0x1 index=0 ossmask=0x00000081 ossdev=7 pcm0: 18: nid=29 dir=0x1 index=0 ossmask=0x00000000 ossdev=0 pcm0: 19: nid=30 dir=0x1 index=0 ossmask=0x00000000 ossdev=0 pcm0: 20: nid=31 dir=0x1 index=0 ossmask=0x00000000 ossdev=0 pcm0: pcm0: +-----------------------------------+ pcm0: | DUMPING HDA AUDIO/VOLUME CONTROLS | pcm0: +-----------------------------------+ pcm0: pcm0: Master Volume (OSS: vol) pcm0: | pcm0: +- nid: 13 index: 0 mute: 1 step: 15 size: 11 off: 15 dir=0x1 ossmask=0x00000021 pcm0: | pcm0: +- nid: 17 index: 0 mute: 1 step: 31 size: 5 off: 23 dir=0x1 ossmask=0x00000011 pcm0: | pcm0: +- nid: 18 index: 0 mute: 1 step: 31 size: 5 off: 23 dir=0x1 ossmask=0x00000081 pcm0: | pcm0: +- nid: 19 index: 0 mute: 1 step: 31 size: 5 off: 23 dir=0x1 ossmask=0x00000041 pcm0: | pcm0: +- nid: 28 index: 0 mute: 1 step: 31 size: 5 off: 23 dir=0x1 ossmask=0x00000081 pcm0: pcm0: PCM Volume (OSS: pcm) pcm0: | pcm0: +- nid: 17 index: 0 mute: 1 step: 31 size: 5 off: 23 dir=0x1 ossmask=0x00000011 pcm0: pcm0: Microphone Volume (OSS: mic) pcm0: | pcm0: +- nid: 18 index: 0 mute: 1 step: 31 size: 5 off: 23 dir=0x1 ossmask=0x00000081 pcm0: | pcm0: +- nid: 28 index: 0 mute: 1 step: 31 size: 5 off: 23 dir=0x1 ossmask=0x00000081 pcm0: pcm0: Line-in Volume (OSS: line) pcm0: | pcm0: +- nid: 19 index: 0 mute: 1 step: 31 size: 5 off: 23 dir=0x1 ossmask=0x00000041 pcm0: pcm0: Recording Level (OSS: rec) pcm0: | pcm0: +- nid: 21 index: 0 mute: 1 step: 15 size: 5 off: 0 dir=0x1 ossmask=0x00000800 pcm0: pcm0: Speaker/Beep (OSS: speaker) pcm0: | pcm0: +- nid: 13 index: 0 mute: 1 step: 15 size: 11 off: 15 dir=0x1 ossmask=0x00000021 pcm0: pcm0: Playback path: pcm0: pcm0: nid=5 [pin: line out (jack)] pcm0: ^ pcm0: | pcm0: +-----<------+ pcm0: ^ pcm0: | pcm0: nid=14 [audio mixer] pcm0: ^ pcm0: | pcm0: nid=17 [audio selector] pcm0: ^ pcm0: | pcm0: nid=3 [audio output] pcm0: pcm0: nid=6 [pin: headphones out (jack)] pcm0: ^ pcm0: | pcm0: +-----<------+ pcm0: ^ pcm0: | pcm0: nid=14 [audio mixer] pcm0: ^ pcm0: | pcm0: nid=17 [audio selector] pcm0: ^ pcm0: | pcm0: nid=3 [audio output] pcm0: pcm0: Recording sources: pcm0: pcm0: nid=21 [audio selector] pcm0: | pcm0: + <- nid=12 [audio mixer] pcm0: | pcm0: + <- nid=9 [pin: line in (jack)] [recsrc: vol, line] pcm0: | pcm0: + <- nid=14 [audio mixer] [recsrc: vol, pcm, speaker, line, mic] pcm0: | pcm0: + <- nid=15 [audio mixer] pcm0: | pcm0: + <- nid=5 [pin: line out (jack)] pcm0: | pcm0: + <- nid=24 [pin: Mic in (jack)] [recsrc: vol, mic] pcm0: pcm0: +--------------------------------------+ pcm0: | DUMPING PCM Playback/Record Channels | pcm0: +--------------------------------------+ pcm0: pcm0: PCM Playback: 1 pcm0: Stream cap: 0x00000001 pcm0: Format: PCM pcm0: PCM cap: 0x000e007f pcm0: PCM size: 16 20 24 pcm0: PCM rate: 44 48 88 96 176 192 pcm0: DAC: 3 pcm0: pcm0: PCM Record: 1 pcm0: Stream cap: 0x00000001 pcm0: Format: PCM pcm0: PCM cap: 0x0006007f pcm0: PCM size: 16 20 pcm0: PCM rate: 44 48 88 96 176 192 pcm0: ADC: 4 (probe0:ata0:0:0:0): error 22 (probe0:ata0:0:0:0): Unretryable Error (probe0:ata0:0:0:0): error 6 (probe0:ata0:0:0:0): Unretryable Error (probe0:ata0:0:0:0): error 22 (probe0:ata0:0:0:0): Unretryable Error (probe1:sbp0:0:0:0): error 22 (probe1:sbp0:0:0:0): Unretryable Error (probe2:sbp0:0:1:0): error 22 (probe2:sbp0:0:1:0): Unretryable Error (probe3:sbp0:0:2:0): error 22 (probe3:sbp0:0:2:0): Unretryable Error (probe4:sbp0:0:3:0): error 22 (probe4:sbp0:0:3:0): Unretryable Error (probe5:sbp0:0:4:0): error 22 (probe5:sbp0:0:4:0): Unretryable Error (probe6:sbp0:0:5:0): error 22 (probe6:sbp0:0:5:0): Unretryable Error (probe7:sbp0:0:6:0): error 22 (probe7:sbp0:0:6:0): Unretryable Error pass0 at ata0 bus 0 target 0 lun 0 pass0: <HL-DT-ST DVDRAM GSA-4082N CQ04> Removable CD-ROM SCSI-0 device pass0: 16.000MB/s transfers GEOM: new disk cd0 ATA PseudoRAID loaded SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000200ef therm: 0x00010200 err: 0x00010000 pcm: 0x00010000 INTR: Assigning IRQ 1 to local APIC 0 ioapic0: Assigning ISA IRQ 1 to local APIC 0 INTR: Assigning IRQ 4 to local APIC 1 ioapic0: Assigning ISA IRQ 4 to local APIC 1 INTR: Assigning IRQ 7 to local APIC 0 ioapic0: Assigning ISA IRQ 7 to local APIC 0 INTR: Assigning IRQ 9 to local APIC 1 ioapic0: Assigning ISA IRQ 9 to local APIC 1 INTR: Assigning IRQ 12 to local APIC 0 ioapic0: Assigning ISA IRQ 12 to local APIC 0 INTR: Assigning IRQ 14 to local APIC 1 ioapic0: Assigning ISA IRQ 14 to local APIC 1 INTR: Assigning IRQ 15 to local APIC 0 ioapic0: Assigning ISA IRQ 15 to local APIC 0 INTR: Assigning IRQ 16 to local APIC 1 ioapic0: Assigning PCI IRQ 16 to local APIC 1 INTR: Assigning IRQ 17 to local APIC 0 ioapic0: Assigning PCI IRQ 17 to local APIC 0 INTR: Assigning IRQ 18 to local APIC 1 ioapic0: Assigning PCI IRQ 18 to local APIC 1 INTR: Assigning IRQ 19 to local APIC 0 ioapic0: Assigning PCI IRQ 19 to local APIC 0 INTR: Assigning IRQ 20 to local APIC 1 ioapic0: Assigning PCI IRQ 20 to local APIC 1 (cd0:ata0:0:0:0): error 6 (cd0:ata0:0:0:0): Unretryable Error cd0 at ata0 bus 0 target 0 lun 0 cd0: <HL-DT-ST DVDRAM GSA-4082N CQ04> Removable CD-ROM SCSI-0 device cd0: 16.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present (cd0:ata0:0:0:0): error 6 (cd0:ata0:0:0:0): Unretryable Error (cd0:ata0:0:0:0): error 6 (cd0:ata0:0:0:0): Unretryable Error (cd0:ata0:0:0:0): error 6 (cd0:ata0:0:0:0): Unretryable Error Trying to mount root from ufs:/dev/ad4s2a start_init: trying /sbin/init acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 splash: image decoder found: daemon_saver acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 battery1: battery initialization failed, giving up acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 60.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 50.0 >= setpoint 45.0 acpi_tz0: _AC3: temperature 50.0 >= setpoint 45.0 acpi_tz0: _CRT value is absurd, ignored (256.0C) acpi_tz0: _AC3: temperature 50.0 >= setpoint 45.0 acpi_tz0: switched from _AC2 to _AC3: 50.0C --=-STXYCKdOyAjC0TaJ1LZW--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1161347795.671.14.camel>