Skip site navigation (1)Skip section navigation (2)
Date:      Sat, 18 Sep 2004 13:30:16 +0400 (MSD)
From:      Stikheev Andrew <sand@zunet.ru>
To:        =?ISO-8859-1?Q?S=F8ren_Schmidt?= <sos@DeepCore.dk>
Cc:        Stikheev Andrew <sand@zunet.ru>
Subject:   Re: ad0: TIMEOUT - READ_DMA retrying (2 retries left) LBA=207594611
Message-ID:  <20040918093016.28438.qmail@zunet.ru>
In-Reply-To: <41498603.4050909@DeepCore.dk>

next in thread | previous in thread | raw e-mail | index | archive | help
[ Charset ISO-8859-1 unsupported, converting... ]
> Stikheev Andrew wrote:
> >    Hi,
> >  
> >     I also have same problems, but only with SATA-disks with
> >    SiI 3112 SATA150 controller (check it with two controllers - onboard
> >    and pci) . Under heavy load on sata-disks system freezes.
> 
> Thats a seprate issue with the sii3112 and your sources are way too old 
> to compare with a new -current.
> You sii3112 timeouts should actually be fixed now :)
  
   Hmm, I update system to last -current(16 Sep), no freezes yet, 
   but too many messages like this:

ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=3526743
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=11862771
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=12951039
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=6576947
ad0: WARNING - WRITE_DMA no interrupt but good status
ad6: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=19113807
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=3526687
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=10133087
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=12910103
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=8493567
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=9095399
ad0: WARNING - WRITE_DMA no interrupt but good status
ad4: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=591
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=10148703
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=9086519
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - READ_DMA retrying (2 retries left) LBA=170119
ad0: WARNING - READ_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=8630335
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=3884127
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=10140639
ad0: WARNING - WRITE_DMA no interrupt but good status
ad0: TIMEOUT - READ_DMA retrying (2 retries left) LBA=7855895
ad0: WARNING - READ_DMA no interrupt but good status
ad4: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=89221071
ad6: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=114679887
ad6: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=114679887


Before update I did not see problems with ad0. 
> 
> -S?ren
> 
> > 
> >  dmesg:  
> > 
> > FreeBSD 5.2-CURRENT #0: Tue Aug 17 00:13:10 MSD 2004
> >     cry0@video:/usr/obj/usr/src/sys/VIDEO
> > Timecounter "i8254" frequency 1193182 Hz quality 0
> > CPU: Intel(R) Celeron(R) CPU 1.70GHz (1703.87-MHz 686-class CPU)
> >   Origin = "GenuineIntel"  Id = 0xf13  Stepping = 3
> >   Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C
> > MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
> > real memory  = 536854528 (511 MB)
> > avail memory = 515768320 (491 MB)
> > npx0: [FAST]
> > npx0: <math processor> on motherboard
> > npx0: INT 16 interface
> > acpi0: <ASUS P4G8X> on motherboard
> > acpi0: [GIANT-LOCKED]
> > acpi0: Power Button (fixed)
> > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> > acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0
> > cpu0: <ACPI CPU> on acpi0
> > acpi_button0: <Power Button> on acpi0
> > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> > pci0: <ACPI PCI bus> on pcib0
> > agp0: <Intel Generic host to PCI bridge> mem 0xf0000000-0xf0ffffff at device 0.0
> >  on pci0
> > pcib1: <ACPI PCI-PCI bridge> mem 0xe8000000-0xe8ffffff at device 1.0 on pci0
> > pci1: <ACPI PCI bus> on pcib1
> > pci0: <serial bus, USB> at device 29.0 (no driver attached)
> > pci0: <serial bus, USB> at device 29.1 (no driver attached)
> > pci0: <serial bus, USB> at device 29.2 (no driver attached)
> > pci0: <serial bus, USB> at device 29.7 (no driver attached)
> > pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> > pci2: <ACPI PCI bus> on pcib2
> > pci2: <display, VGA> at device 0.0 (no driver attached)
> > fxp0: <Intel 82558 Pro/100 Ethernet> port 0xb800-0xb81f mem 0xdf800000-0xdf8ffff
> > f,0xe7000000-0xe7000fff irq 9 at device 2.0 on pci2
> > miibus0: <MII bus> on fxp0
> > inphy0: <i82555 10/100 media interface> on miibus0
> > inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > fxp0: Ethernet address: 00:04:ac:58:e1:26
> > fxp0: [GIANT-LOCKED]
> > bge0: <Broadcom BCM5702 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xdf000000-0xdf0
> > 0ffff irq 10 at device 5.0 on pci2
> > miibus1: <MII bus> on bge0
> > brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus1
> > brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX
> > -FDX, auto
> > bge0: Ethernet address: 00:0c:6e:11:8d:2f
> > bge0: [GIANT-LOCKED]
> > atapci0: <SiI 3112 SATA150 controller> port 0xa000-0xa00f,0xa400-0xa403,0xa800-0
> > xa807,0xb000-0xb003,0xb400-0xb407 mem 0xde800000-0xde8001ff irq 5 at device 6.0 
> > on pci2
> > ata2: at 0xde800000 on atapci0
> > ata3: at 0xde800000 on atapci0
> > fxp1: <Intel 82558 Pro/100 Ethernet> port 0x9800-0x981f mem 0xde000000-0xde0ffff
> > f,0xe6000000-0xe6000fff irq 10 at device 7.0 on pci2
> > miibus2: <MII bus> on fxp1
> > inphy1: <i82555 10/100 media interface> on miibus2
> > inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > fxp1: Ethernet address: 00:04:ac:58:aa:c3
> > fxp1: [GIANT-LOCKED]
> > isab0: <PCI-ISA bridge> at device 31.0 on pci0
> > isa0: <ISA bus> on isab0
> > atapci1: <Intel ICH4 UDMA100 controller> port 0xf000-0xf00f,0x376,0x170-0x177,0x
> > 3f6,0x1f0-0x1f7 irq 10 at device 31.1 on pci0
> > ata0: at 0x1f0 irq 14 on atapci1
> > ata1: at 0x170 irq 15 on atapci1
> > fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0
> > x3f5 irq 6 drq 2 on acpi0
> > fdc0: FIFO enabled, 8 bytes threshold
> > ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
> > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> > ppc0: FIFO with 16/16/16 bytes threshold
> > ppbus0: <Parallel port bus> on ppc0
> > plip0: <PLIP network interface> on ppbus0
> > lpt0: <Printer> on ppbus0
> > lpt0: Interrupt-driven port
> > ppi0: <Parallel I/O> on ppbus0
> > sio0 port 0x3f8-0x3ff irq 4 on acpi0
> > sio0: type 16550A, console
> > sio1 port 0x2f8-0x2ff irq 3 on acpi0
> > sio1: type 16550A
> > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
> > pmtimer0 on isa0
> > orm0: <ISA Option ROMs> at iomem 0xd4000-0xd47ff,0xcc000-0xd07ff,0xc8000-0xc87ff
> > ,0xc0000-0xc7fff on isa0
> > sc0: <System console> at flags 0x100 on isa0
> > sc0: VGA <16 virtual consoles, flags=0x100>
> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> > Timecounter "TSC" frequency 1703871540 Hz quality 800
> > Timecounters tick every 1.000 msec
> > ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to acc
> > ept, logging disabled
> > ad0: 152627MB <WDC WD1600JB-00EVA0> [310101/16/63] at ata0-master UDMA100
> > ad1: 239372MB <Maxtor 7Y250P0> [486344/16/63] at ata0-slave UDMA100
> > ad2: 190782MB <WDC WD2000JB-00EVA0> [387621/16/63] at ata1-master UDMA100
> > ad3: 238475MB <WDC WD2500JB-00EVA0> [484521/16/63] at ata1-slave UDMA100
> > ad4: 190782MB <WDC WD2000JD-00GBB0> [387621/16/63] at ata2-master SATA150
> > ad6: 238475MB <WDC WD2500JD-00FYB0> [484521/16/63] at ata3-master SATA150
> > 
> >  Last messages before system hangs :
> > 
> > ad4: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=9557199
> > ad4: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=591
> > ad4: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=591
> > ad4: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=95566671
> > ad4: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=95566671
> > ad4: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=193622479
> > ad6: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA=267662031
> > 
> 
> 
> 

-- 
                                        Best regards,   
                                        Stihkeev Andrew 



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040918093016.28438.qmail>