Date: Thu, 8 Feb 2001 16:14:44 +0100 From: Edwin Mons <e@ik.nu> To: freebsd-hardware@freebsd.org Subject: Compaq Proliant + SmartArray problem Message-ID: <20010208161444.A96172@ik.nu>
next in thread | raw e-mail | index | archive | help
Hi.
I try to boot a Compaq Proliant 1600 equipped with a Compaq
SMARTarray 4200 with FreeBSD 4.2. I cannot use the smartarray
unless I disable the symbios driver which drives the onboard
SCSI controllers. Below is a log of a verbose boot. Any clues
anybody?
Edwinm
SMAP type=01 base=00000000 00000000 len=00000000 0009f800
SMAP type=02 base=00000000 0009f800 len=00000000 00000800
SMAP type=02 base=00000000 000f0000 len=00000000 00010000
SMAP type=01 base=00000000 00100000 len=00000000 17f00000
SMAP type=02 base=00000000 fec00000 len=00000000 00010000
SMAP type=02 base=00000000 fee00000 len=00000000 00010000
SMAP type=02 base=00000000 fff80000 len=00000000 00080000
SMAP type=01 base=00000001 00000000 len=00000000 00000000
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.2-RELEASE #0: Thu Feb 8 14:08:12 GMT 2001
root@:/usr/src/sys/compile/ILSE.IDA
Calibrating clock(s) ... TSC clock: 498673485 Hz, i8254 clock: 1193150 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 498688414 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (498.69-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 402653184 (393216K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00371000 - 0x17ff7fff, 399011840 bytes (97415 pages)
avail memory = 388464640 (379360K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00ffee0
bios32: Entry = 0xf0000 (c00f0000) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x80
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel.ida" at 0xc0358000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71928086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71928086)
pcib0: <Intel 82443BX host to PCI bridge (AGP disabled)> on motherboard
found-> vendor=0x8086, dev=0x7192, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base 00000000, size 28
found-> vendor=0x1013, dev=0x00b8, revid=0x45
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base c4000000, size 25
map[14]: type 1, range 32, base c6dff000, size 12
found-> vendor=0x1011, dev=0x0022, revid=0x04
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x0e11, dev=0xa0f0, revid=0x00
class=08-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 1, range 32, base 00001800, size 8
map[14]: type 1, range 32, base c6dfef00, size 8
found-> vendor=0x8086, dev=0x1229, revid=0x05
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=15
map[10]: type 1, range 32, base c3fff000, size 12
map[14]: type 1, range 32, base 00002000, size 5
map[18]: type 1, range 32, base c6e00000, size 20
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000f100, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=0
found-> vendor=0x8086, dev=0x7113, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
pci0: <PCI bus> on pcib0
pci0: <Cirrus Logic GD5446 SVGA controller> (vendor=0x1013, dev=0x00b8) at 11.0
pcib1: <DEC 21150 PCI-PCI bridge> at device 13.0 on pci0
found-> vendor=0x0e11, dev=0xae43, revid=0x10
class=02-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base 00003c00, size 4
map[14]: type 1, range 32, base c6ffcdf0, size 4
found-> vendor=0x1000, dev=0x000f, revid=0x14
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 00003000, size 8
map[14]: type 1, range 32, base c6ffcf00, size 8
map[18]: type 1, range 32, base c6fff000, size 12
found-> vendor=0x1000, dev=0x000f, revid=0x14
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=11
map[10]: type 1, range 32, base 00003400, size 8
map[14]: type 1, range 32, base c6ffce00, size 8
map[18]: type 1, range 32, base c6ffe000, size 12
found-> vendor=0x1011, dev=0x0046, revid=0x01
class=01-04-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base c6ffd000, size 12
map[14]: type 1, range 32, base 00003800, size 8
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x0e11, dev=0xae43) at 7.0 irq 9
sym0: <875> port 0x3000-0x30ff mem 0xc6fff000-0xc6ffffff,0xc6ffcf00-0xc6ffcfff irq 10 at device 9.0 on pci1
sym0: chip clock is 40401KHz
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym1: <875> port 0x3400-0x34ff mem 0xc6ffe000-0xc6ffefff,0xc6ffce00-0xc6ffceff irq 11 at device 9.1 on pci1
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
ida0: <Compaq Smart Array 4200 controller> port 0x3800-0x38ff mem 0xc6ffd000-0xc6ffdfff irq 5 at device 10.0 on pci1
ida0: can't allocate memory resources
device_probe_and_attach: ida0 attach returned 12
pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 14.0
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x2000-0x201f mem 0xc6e00000-0xc6efffff,0xc3fff000-0xc3ffffff irq 15 at device 15.0 on pci0
fxp0: Ethernet address 00:a0:c9:a5:e1:f4
bpf: fxp0 attached
isab0: <Intel 82371AB PCI to ISA bridge> at device 20.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf100-0xf10f at device 20.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xf100
ata0: mask=03 status0=50 status1=51
ata0: mask=03 ostat0=50 ostat2=51
ata0-master: ATAPI probe a=14 b=eb
ata0-slave: ATAPI probe a=7f b=7f
ata0: mask=03 status0=00 status1=00
ata0-slave: ATA probe a=04 b=7f
ata0: devices=04
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xf108
ata1: mask=00 status0=ff status1=ff
ata1: probe allocation failed
pci0: <Intel 82371AB/EB (PIIX4) USB controller> (vendor=0x8086, dev=0x7112) at 20.2 irq 0
chip1: <Intel 82371AB Power management controller> at device 20.3 on pci0
eisa0: <EISA bus> on motherboard
mainboard0: <CPQ0689 (System Board)> on eisa0 slot 0
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata3: mask=00 status0=ff status1=ff
ata3: probe allocation failed
ata3 failed to probe at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 01 40 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x3bc
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> failed to probe at port 0x3bc-0x3c3 irq 7 on isa0
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fffe20 0..1023=1024 cylinders, 0..254=255 heads, 1..32=32 sectors
0 accounted for
Device configuration finished.
bpf: faith0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: lo0 attached
ata0-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
ata0-master: success setting PIO4 on generic chip
acd0: <COMPAQ XM-6402B/1723> CDROM drive at ata0 as master
acd0: read 5512KB/s (5512KB/s), 256KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream
acd0: Audio: play, 16 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
sa0 at sym1 bus 0 target 6 lun 0
sa0: <COMPAQ SDT-10000 1.05> Removable Sequential Access SCSI-2 device
sa0: Serial Number 0004902498
sa0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
pass0 at sym1 bus 0 target 6 lun 0
pass0: <COMPAQ SDT-10000 1.05> Removable Sequential Access SCSI-2 device
pass0: Serial Number 0004902498
pass0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
no devsw (majdev=0 bootdev=0xa0300000)
Mounting root from ufs:/dev/idad0s2a
no such device 'idad'
setrootbyname failed
ffs_mountroot: can't find rootvp
Root mount failed: 6
Manual root filesystem specification:
<fstype>:<device> Mount <device> using filesystem <fstype>
eg. ufs:/dev/da0s1a
? List valid disk boot devices
<empty line> Abort manual input
mountroot>
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20010208161444.A96172>