Date: Fri, 16 Nov 2018 19:06:55 -0500 From: Dennis Clarke <dclarke@blastwave.org> To: Mark Millard <marklmi@yahoo.com> Cc: FreeBSD PowerPC ML <freebsd-ppc@freebsd.org> Subject: Re: The PowerMac G5 internal hard disk SATA question Message-ID: <a2b99b15-ecb2-7742-d470-fba5dde2a390@blastwave.org> In-Reply-To: <EBB0C56C-61FF-4A61-BBB4-2E329646DD21@yahoo.com> References: <157b8bec-f5f6-08ba-cc2e-a58dc42894c5@blastwave.org> <20181115104303.631cb9d8@ralga.knownspace> <60a561b1-23c0-7181-05a5-609008b1f06e@blastwave.org> <EBB0C56C-61FF-4A61-BBB4-2E329646DD21@yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On 11/15/18 5:40 PM, Mark Millard wrote:
> On 2018-Nov-15, at 13:07, Dennis Clarke <dclarke at blastwave.org> wrote:
>
>> On 11/15/18 11:43 AM, Justin Hibbits wrote:
>>> On Thu, 15 Nov 2018 11:18:43 -0500
>>> Dennis Clarke <dclarke@blastwave.org> wrote:
>>>> Someone (offlist) asked if my shiney new Seagate hard disk was
>>>> compatible with SATA-I and I wouldn't know. I have had various types
>>>> of hard disks in this thing and also some SSD types. Nothing is very
>>>> fast and all of them worked.
>>>><snip>
It has taken a day of disk tests but I seem to be stuck using the Apple
Hitachi disk in the upper slot and finally an install boots but with
kern.smp.disabled=1 :
root@eris:~ # dmesg
---<<BOOT>>---
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.0-BETA4 r340271 GENERIC powerpc
gcc version 4.2.1 20070831 patched [FreeBSD]
VT(ofwfb): resolution 1280x1024
cpu0: IBM PowerPC 970MP revision 1.1, 2500.34 MHz
cpu0: Features dc000000<PPC32,PPC64,ALTIVEC,FPU,MMU>
cpu0: HID0 1511081<DEEPNAP,NAP,DPM,NHR,TBEN,ENATTN>
real memory = 8542408704 (8146 MB)
avail memory = 8152756224 (7775 MB)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree> on nexus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
pcr0: <PPC 970 Power Control Register> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
pcr1: <PPC 970 Power Control Register> on cpu1
cpu2: <Open Firmware CPU> on cpulist0
pcr2: <PPC 970 Power Control Register> on cpu2
cpu3: <Open Firmware CPU> on cpulist0
pcr3: <PPC 970 Power Control Register> on cpu3
powermac_nvram0: <Apple NVRAM> mem 0xfff04000-0xfff07fff on ofwbus0
powermac_nvram0: bank0 generation 452, bank1 generation 453
unin0: <Apple UniNorth System Controller> mem 0xf8000000-0xf8ffffff on
ofwbus0
unin0: Version 66
iichb0: <Keywest I2C controller> mem 0xf8001000-0xf8001fff irq 0 on unin0
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
ds17750: <Temp-Monitor DS1775> at addr 0x94 on iicbus0
ds16310: <Temp-Monitor DS1631> at addr 0x96 on iicbus0
max66900: <Temp-Monitor MAX6690> at addr 0x98 on iicbus0
max66901: <Temp-Monitor MAX6690> at addr 0x9c on iicbus0
htpic0: <OpenPIC Interrupt Controller> mem 0xf8040000-0xf807ffff on unin0
pcib0: <IBM CPC945 PCI Express Root> mem 0xf0000000-0xf1ffffff on ofwbus0
pci0: <OFW PCI bus> on pcib0
vgapci0: <VGA-compatible display> mem
0xa1000000-0xa1ffffff,0x90000000-0x9fffffff,0xa0000000-0xa0ffffff irq 3
at device 0.0 on pci0
vgapci0: Boot video device
pcib1: <IBM CPC9X5 HyperTransport Tunnel> mem
0xf2000000-0xf47fffff,0xf8070000-0xf8070fff on ofwbus0
pcib1: 86 HT IRQs on device 7.0
pci1: <OFW PCI bus> on pcib1
pcib1: Enabling MSI window for HyperTransport slave at pci1:0:1:0
pcib2: <OFW PCI-PCI bridge> at device 1.0 on pci1
pci2: <OFW PCI bus> on pcib2
pcib3: <OFW PCI-PCI bridge> at device 2.0 on pci1
pci3: <OFW PCI bus> on pcib3
bge0: <Broadcom BCM5714 B3, ASIC rev. 0x008003> mem
0xfa530000-0xfa53ffff,0xfa520000-0xfa52ffff irq 66 at device 4.0 on pci3
bge0: CHIP ID 0x00008003; ASIC REV 0x08; CHIP REV 0x80; PCI-X 33 MHz
miibus0: <MII bus> on bge0
brgphy0: <BCM5780 1000BASE-T media interface> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: Ethernet address: 00:14:51:64:67:10
bge1: <Broadcom BCM5714 B3, ASIC rev. 0x008003> mem
0xfa510000-0xfa51ffff,0xfa500000-0xfa50ffff irq 67 at device 4.1 on pci3
bge1: CHIP ID 0x00008003; ASIC REV 0x08; CHIP REV 0x80; PCI-X 33 MHz
miibus1: <MII bus> on bge1
brgphy1: <BCM5780 1000BASE-T media interface> PHY 1 on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge1: Ethernet address: 00:14:51:64:67:11
pcib4: <OFW PCI-PCI bridge> at device 3.0 on pci1
pci4: <OFW PCI bus> on pcib4
pcib5: <OFW PCI-PCI bridge> at device 4.0 on pci1
pci5: <OFW PCI bus> on pcib5
pcib6: <OFW PCI-PCI bridge> at device 5.0 on pci1
pci6: <OFW PCI bus> on pcib6
pcib7: <OFW PCI-PCI bridge> at device 6.0 on pci1
pci7: <OFW PCI bus> on pcib7
pcib8: <OFW PCI-PCI bridge> at device 7.0 on pci1
pci8: <OFW PCI bus> on pcib8
gem0: <Apple Shasta GMAC Ethernet> mem 0xfa200000-0xfa3fffff at device
15.0 on pci8
gem0: invalid MAC address
device_attach: gem0 attach returned 6
pcib9: <OFW PCI-PCI bridge> at device 8.0 on pci1
pci9: <OFW PCI bus> on pcib9
macio0: <Shasta I/O Controller> mem 0x80000000-0x8007ffff at device 7.0
on pci9
macgpio0: <MacIO GPIO Controller> mem 0x50-0x8a on macio0
scc0: <Zilog Z8530 dual channel SCC> mem
0x13000-0x13fff,0x8400-0x84ff,0x8500-0x85ff,0x8600-0x86ff,0x8700-0x87ff
irq 23,17,18,24,19,20 on macio0
uart0: <z8530, channel A> on scc0
uart1: <z8530, channel B> on scc0
iichb1: <Keywest I2C controller> mem 0x18000-0x18fff irq 27 on macio0
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
onyx0: <Texas Instruments PCM3052 Audio Codec> at addr 0x8c on iicbus1
iicbus1: <unknown card> at addr 0x24
pcm0: <Apple I2S Audio Controller> mem
0x10000-0x10fff,0x8000-0x80ff,0x8100-0x81ff irq 28,11,12,30,15,16 on macio0
ohci0: <NEC uPD 9210 USB controller> mem 0x80082000-0x80082fff irq 70 at
device 11.0 on pci9
usbus0 on ohci0
ohci1: <NEC uPD 9210 USB controller> mem 0x80081000-0x80081fff irq 70 at
device 11.1 on pci9
usbus1 on ohci1
ehci0: <NEC uPD 72010x USB 2.0 controller> mem 0x80080000-0x800800ff irq
70 at device 11.2 on pci9
usbus2: EHCI version 1.0
usbus2 on ehci0
pcib10: <OFW PCI-PCI bridge> at device 9.0 on pci1
pci10: <OFW PCI bus> on pcib10
atapci0: <ServerWorks K2 SATA150 controller> mem 0xfa402000-0xfa403fff
irq 10 at device 12.0 on pci10
pcib1: failed to reserve resource for pcib10
atapci0: 0x10 bytes of rid 0x20 res 4 failed (0, 0xffffffffffffffff).
ata2: <ATA channel> at channel 0 on atapci0
ata3: <ATA channel> at channel 1 on atapci0
ata4: <ATA channel> at channel 2 on atapci0
ata5: <ATA channel> at channel 3 on atapci0
ata0: <Shasta Kauai ATA Controller> mem 0xfa404000-0xfa407fff irq 38,37
at device 13.0 on pci10
fwohci0: <1394 Open Host Controller Interface> mem 0xfa400000-0xfa400fff
irq 39 at device 14.0 on pci10
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 00:11:24:ff:fe:e5:13:d0
fwohci0: invalid speed 7 (fixed to 3).
fwohci0: Phy 1394a available S800, 3 ports.
fwohci0: Link S800, max_rec 4096 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:11:24:e5:13:d0
fwe0: Ethernet address: 02:11:24:e5:13:d0
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: PhysicalUpperBound register is not implemented. Physical
memory access is limited to the first 4GB
fwohci0: PhysicalUpperBound = 0x00000000
fwohci0: fwohci_intr_core: node_id=0x00000001, SelfID Count=1,
CYCLEMASTER mode
smu0: <Apple System Management Unit> on ofwbus0
smu0: registered as a time-of-day clock, resolution 0.001000s
iichb2: <SMU I2C controller> on smu0
iicbus2: <OFW I2C bus> on iichb2
iic2: <I2C generic I/O> on iicbus2
smusat0: <SMU Satellite Sensors> at addr 0xb0 on iicbus2
smusat1: <SMU Satellite Sensors> at addr 0xb2 on iicbus2
iicbus2: <unknown card> at addr 0xd4
iichb3: <SMU I2C controller> on smu0
iicbus3: <OFW I2C bus> on iichb3
iic3: <I2C generic I/O> on iicbus3
Timecounter "timebase" frequency 33333333 Hz quality 0
Event timer "decrementer" frequency 33333333 Hz quality 1000
Timecounters tick every 1.000 msec
firewire0: 2 nodes, maxhop <= 1 cable IRM irm(1) (me)
firewire0: bus manager 1
bge0: link state changed to UP
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
max66900: 2 sensors detected.
max66901: 2 sensors detected.
ugen1.1: <NEC OHCI root HUB> at usbus1
uhub0: <NEC OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen0.1: <NEC OHCI root HUB> at usbus0
uhub1: <NEC OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
usbus2: 480Mbps High Speed USB v2.0
ugen2.1: <NEC EHCI root HUB> at usbus2
uhub2: <NEC EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
uhub0: 2 ports with 2 removable, self powered
uhub1: 3 ports with 3 removable, self powered
uhub2: 5 ports with 5 removable, self powered
ada0 at ata2 bus 0 scbus0 target 0 lun 0
ada0: <Hitachi HDS725050KLA360 K2ABC20A> ATA-7 SATA 1.x device
ada0: Serial Number KRVN23ZAHA5DBD
ada0: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
ada0: 476940MB (976773168 512 byte sectors)
SMP: AP CPU #1 launched
SMP: AP CPU #2 launched
SMP: AP CPU #3 launched
Trying to mount root from ufs:/dev/ada0s3 [rw]...
cd0 at ata0 bus 0 scbus4 target 0 lun 0
cd0: <HL-DT-ST DVD-RW GWA-4165B C006> Removable CD-ROM SCSI device
cd0: Serial Number M0063NE3358
cd0: 66.700MB/s transfers (UDMA4, ATAPI 12bytes, PIO 65534bytes)
cd0: 4482MB (2295104 2048 byte sectors)
ugen1.2: <Lite-On Technology Corp. USB Multimedia Keyboard> at usbus1
ukbd0 on uhub0
ukbd0: <Lite-On Technology Corp. USB Multimedia Keyboard, class 0/0, rev
1.10/1.04, addr 2> on usbus1
kbd1 at ukbd0
uhid0 on uhub0
uhid0: <Lite-On Technology Corp. USB Multimedia Keyboard, class 0/0, rev
1.10/1.04, addr 2> on usbus1
lo0: link state changed to UP
bge0: link state changed to DOWN
bge0: link state changed to UP
Security policy loaded: MAC/ntpd (mac_ntpd)
module_register: cannot register gem/miibus from if_gem.ko; already
loaded from kernel
Module gem/miibus failed to register: 17
module_register: cannot register pci/gem from if_gem.ko; already loaded
from kernel
Module pci/gem failed to register: 17
root@eris:~ #
Dennis
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?a2b99b15-ecb2-7742-d470-fba5dde2a390>