Date: Mon, 09 Dec 2002 17:30:14 -0800 From: James Satterfield <james@uberduper.com> To: Dimitry Andric <dim@xs4all.nl> Cc: FreeBSD Current List <current@FreeBSD.ORG> Subject: Re: RC1 sysinstall hang Message-ID: <3DF543A6.5090500@uberduper.com> In-Reply-To: <1439619692.20021209234634@xs4all.nl> References: <1439619692.20021209234634@xs4all.nl>
next in thread | previous in thread | raw e-mail | index | archive | help
Dimitry Andric wrote: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > Hi, > > Having tried 5.0-DP1 before on a certain box (see below for dmesg), I > tried booting a 5.0-RC1 CD on it. However, sysinstall always hangs at > "probing devices", although it reacts to ^C. Restarting it doesn't > really help, though, it simply hangs again. I've let it run for >30 > minutes, but still nothing. > > With -DP1, sysinstall had no problems, and that version is still > running on the box, giving the following dmesg: > > ================== > Copyright (c) 1992-2002 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.0-DP1 #0: Sun Apr 7 02:51:42 GMT 2002 > murray@builder.freebsdmall.com:/usr/src/sys/i386/compile/GENERIC > Preloaded elf kernel "/boot/kernel/kernel" at 0xc053e000. > Preloaded elf module "/boot/kernel/acpi.ko" at 0xc053e0a8. > Timecounter "i8254" frequency 1193182 Hz > Timecounter "TSC" frequency 451024348 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (451.02-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x673 Stepping = 3 > Features=0x383f9ff > real memory = 268423168 (262132K bytes) > avail memory = 255545344 (249556K bytes) > Pentium Pro MTRR support enabled > Using $PIR table, 8 entries at 0xc00f0d10 > npx0: on motherboard > npx0: INT 16 interface > acpi0: on motherboard > acpi0: power button is handled as a fixed feature programming model. > ACPI timer looks GOOD min = 2, max = 4, width = 3 > ACPI timer looks GOOD min = 2, max = 4, width = 3 > ACPI timer looks BAD min = 2, max = 5, width = 4 > ACPI timer looks BAD min = 2, max = 5, width = 4 > ACPI timer looks BAD min = 2, max = 5, width = 4 > ACPI timer looks BAD min = 2, max = 5, width = 4 > ACPI timer looks BAD min = 2, max = 16777187, width = 16777186 > ACPI timer looks GOOD min = 2, max = 4, width = 3 > ACPI timer looks BAD min = 2, max = 5, width = 4 > ACPI timer looks GOOD min = 2, max = 4, width = 3 > Timecounter "ACPI-safe" frequency 3579545 Hz > acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0 > acpi_cpu0: on acpi0 > acpi_button0: on acpi0 > acpi_pcib0: port 0xcf8-0xcff on acpi0 > pci0: on acpi_pcib0 > pcib1: at device 1.0 on pci0 > pci1: on pcib1 > pci1: at device 0.0 (no driver attached) > isab0: at device 4.0 on pci0 > isa0: on isab0 > atapci0: port 0xd800-0xd80f at device 4.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > uhci0: port 0xd400-0xd41f irq 5 at device 4.2 on pci0 > usb0: on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > pci0: at device 4.3 (no driver attached) > ahc0: port 0xd000-0xd0ff mem 0xde800000-0xde800fff irq 5 at device > 6.0 on pci0 > aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs > fxp0: port 0xb800-0xb81f mem > 0xde000000-0xde0fffff,0xe1000000-0xe1000fff irq 10 at device 7.0 on pci0 > fxp0: Ethernet address 00:e0:18:90:87:b2 > inphy0: on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > pci0: at device 10.0 (no driver attached) > fdc0: port 0x3f7,0x3f2-0x3f5 irq 6 on acpi0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > ppc0 port 0x778-0x77b,0x378-0x37f irq 7 on acpi0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/9 bytes threshold > plip0: on ppbus0 > lpt0: on ppbus0 > lpt0: Interrupt-driven port > ppi0: on ppbus0 > sio0 port 0x3f8-0x3ff irq 4 on acpi0 > sio0: type 16550A > sio1 port 0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > atkbdc0: port 0x64,0x60 irq 1 on acpi0 > atkbd0: flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: irq 12 on atkbdc0 > psm0: model IntelliMouse, device ID 3 > orm0: at iomem 0xc0000-0xcffff on isa0 > pmtimer0 on isa0 > sc0: at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Waiting 15 seconds for SCSI devices to settle > Mounting root from ufs:/dev/da0s4a > da1 at ahc0 bus 0 target 1 lun 0 > da1: Fixed Direct Access SCSI-2 device > da1: 40.000MB/s transfers (20.000MHz, offset 31, 16bit), Tagged > Queueing Enabled > da1: 4341MB (8890760 512 byte sectors: 255H 63S/T 553C) > da0 at ahc0 bus 0 target 0 lun 0 > da0: Fixed Direct Access SCSI-3 device > da0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged > Queueing Enabled > da0: 17519MB (35879135 512 byte sectors: 255H 63S/T 2233C) > da2 at ahc0 bus 0 target 2 lun 0 > da2: Fixed Direct Access SCSI-2 device > da2: 40.000MB/s transfers (20.000MHz, offset 31, 16bit), Tagged > Queueing Enabled > da2: 2170MB (4445380 512 byte sectors: 255H 63S/T 276C) > cd0 at ahc0 bus 0 target 4 lun 0 > cd0: Removable CD-ROM SCSI-2 device > cd0: 20.000MB/s transfers (20.000MHz, offset 15) > cd0: Attempt to query device size failed: NOT READY, Medium not present > cd1 at ahc0 bus 0 target 5 lun 0 > cd1: Removable CD-ROM SCSI-2 device > cd1: 20.000MB/s transfers (20.000MHz, offset 16) > cd1: Attempt to query device size failed: NOT READY, Medium not present > cd2 at ahc0 bus 0 target 6 lun 0 > cd2: Removable CD-ROM SCSI-4 device > cd2: 10.000MB/s transfers (10.000MHz, offset 15) > cd2: Attempt to query device size failed: NOT READY, Medium not present > da3 at ahc0 bus 0 target 3 lun 0 > da3: Removable Direct Access SCSI-2 device > da3: 3.300MB/s transfers > da3: Attempt to query device size failed: NOT READY, Medium not present > ================== > > If anyone has suggestions on how to get sysinstall to stop hanging, > please let me know. :-) > > Cheers, > - -- > Dimitry Andric > PGP Key: http://www.xs4all.nl/~dim/dim.asc > Fingerprint: 7AB462D2CE35FC6D42394FCDB05EA30A2E2096A3 > Lbh whfg ivbyngrq gur QZPN naq jvyy or cebfrphgrq > > -----BEGIN PGP SIGNATURE----- > Version: 6.5.8ckt http://www.ipgpp.com/ > Comment: http://duncan.gn.apc.org/stoa_cover.htm > > iQA/AwUBPfUPRLBeowouIJajEQJcxgCePV2iNh6kjuV7Xvfo4wTHR2zB6NgAoLdn > Xqo3UXMCxHTBciPhWeBC8sVf > =DdC7 > -----END PGP SIGNATURE----- > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-current" in the body of the message > Unplug the Zip drive. I've had the same problem with sysinstall and a USB zip drive. James. To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3DF543A6.5090500>