Date: Fri, 25 Mar 2005 21:22:07 +0100 From: "=?iso-8859-15?Q?Jos=E9?= M. =?iso-8859-15?Q?Fandi=F1o?=" <bsdalpha@fadesa.es> Cc: freebsd-alpha@freebsd.org Subject: Re: 5.4b1 on Miata Message-ID: <424472EF.4CC4B62C@fadesa.es> References: <42444922.794080FB@fadesa.es> <20050325174320.GH2324@cicely12.cicely.de> <4244542E.82ECC7F8@fadesa.es> <20050325194718.GN2324@cicely12.cicely.de>
next in thread | previous in thread | raw e-mail | index | archive | help
Bernd Walter wrote:
> > > Did it ever run any FreeBSD version?
> >
> > Actually it runs FreeBSD 5.2.1-RELEASE.
> >
> > > It is not unlikely that the qlogic card needs to be in a specific slot
> > > to work.
> >
> > it's in pci1:4:0, did you suggest that maybe I must change the slot?
>
> No - if there are slot specific problems then you have problems with
> 5.2.1 as well.
> If you compare boot messages with 5.2.1 - what are the next lines
> that should have been printed after the problem point?
Bernd,
the last line printed in 5.4b1 is "isp0: Initiator ID is 7 on Channel 0"
whilst in 5.2.1 boot continues.
Also "core version" for 5.2.1 is 2.7 and 2.9 in 5.4b1, it might have
some relation?
Qlogic ISP Driver, FreeBSD Version 5.9, Core Version 2.7
isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x8000-0x80ff mem 0x81010000-0x81010fff irq 3 at device 4.0 on pci1
pcib1: device isp0 requested decoded memory range 0x81010000-0x81010fff
isp0: using Memory space register mapping
isp0: interrupting at CIA irq 3
isp0: Ultra Mode Capable
isp0: Board Type 1040B, Chip Revision 0x5, loaded F/W Revision 4.66.0
isp0: Last F/W revision was 5.57.1
isp0: 243 max I/O commands supported
isp0: Initiator ID is 7 on Channel 0
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
> atacontrol list
ATA channel 0:
Master: acd0 <Compaq CRD-8322B/1.07> ATA/ATAPI rev 0
Slave: no device present
ATA channel 1:
Master: no device present
Slave: no device present
> camcontrol devlist
<IBM DDRS-34560D DC1B> at scbus0 target 0 lun 0 (pass0,da0)
<IBM DDRS-34560D DC1B> at scbus0 target 1 lun 0 (pass1,da1)
<DEC TLZ10 (C) DEC 04a8> at scbus0 target 5 lun 0 (sa0,pass2)
<IBM DDRS-34560D DC1B> at scbus0 target 6 lun 0 (pass3,da2)
<IBM DDRS-34560D DC1B> at scbus0 target 10 lun 0 (pass4,da3)
/--------------/
(boot dkc0.0.0.1004.0 -file kernel -flags a)
block 0 of dkc0.0.0.1004.0 is a valid boot block
reading 15 blocks from dkc0.0.0.1004.0
bootstrap code read in
base = 1e6000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 1d8000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Loading /boot/loader
Console: SRM firmware console
VMS PAL rev: 0x1000000010114
OSF PAL rev: 0x1000000020116
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM disk boot, Revision 1.2
(root@demonio.servidores.fadesa, Fri Feb 27 15:29:55 CET 2004)
Memory: 196608 k
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x4c75e0+0x42540 syms=[0x8+0x66e10+0x8+0x5044c]
/boot/kernel/if_xl.ko text=0xa758 data=0xcc8+0x8 syms=[0x8+0x1200+0x8+0xbdb]
Hit [Enter] to boot immediately, or any other key for command prompt.
Type '?' for a list of commands, 'help' for more detailed help.
OK boot -v
Entering /boot/kernel/kernel at 0xfffffc0000343840...
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2.1-RELEASE #0: Thu Feb 26 18:53:44 CET 2004
root@demonio.servidores.fadesa:/usr/src/sys/alpha/compile/NUCLEO
Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc00008e2000.
Preloaded elf module "/boot/kernel/if_xl.ko" at 0xfffffc00008e20e0.
Digital Personal Workstation (Miata)
Digital Personal WorkStation 500au, 500MHz
8192 byte page size, 1 processor.
CPU: EV56 (21164A) major=7 minor=0 extensions=0x1<BWX>
OSF PAL rev: 0x1000000020116
real memory = 199327744 (190 MB)
Physical memory chunk(s):
0x00904000 - 0x0bd09fff, 188768256 bytes (23043 pages)
avail memory = 185409536 (176 MB)
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
cia0: <2117x Core Logic chipset>
cia0: Pyxis, pass 1
cia0: extended capabilities: 1<BWEN>
pcib0: <2117x PCI host bus adapter> on cia0
pci0: <PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 4, range 32, base 00009000, size 7, enabled
map[14]: type 1, range 32, base 81181000, size 7, enabled
found-> vendor=0x1011, dev=0x0019, revid=0x30
bus=0, slot=3, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0047, statreg=0x0280, cachelnsz=16 (dwords)
lattimer=0xff (7650 ns), mingnt=0x14 (5000 ns), maxlat=0x28 (10000 ns)
intpin=a, irq=0
found-> vendor=0x1080, dev=0xc693, revid=0x00
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0047, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 000001f0, size 3, enabled
map[14]: type 4, range 32, base 000003f4, size 2, enabled
map[20]: type 4, range 32, base 000090a0, size 4, enabled
found-> vendor=0x1080, dev=0xc693, revid=0x00
bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=1
cmdreg=0x0045, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=238
map[10]: type 4, range 32, base 00000170, size 3, enabled
map[14]: type 4, range 32, base 00000374, size 2, enabled
map[20]: type 1, range 32, base 81170000, size 16, memory disabled
found-> vendor=0x1080, dev=0xc693, revid=0x00
bus=0, slot=7, func=2
class=01-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0045, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=239
map[10]: type 1, range 32, base 81180000, size 12, enabled
found-> vendor=0x1080, dev=0xc693, revid=0x00
bus=0, slot=7, func=3
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0047, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0xf8 (7440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=234
map[10]: type 1, range 32, base 81140000, size 17, enabled
map[14]: type 1, range 32, base 80800000, size 23, enabled
map[18]: type 1, range 32, base 80000000, size 23, enabled
found-> vendor=0x104c, dev=0x3d07, revid=0x01
bus=0, slot=12, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0xff (7650 ns), mingnt=0xc0 (48000 ns), maxlat=0xc0 (48000 ns)
intpin=a, irq=8
found-> vendor=0x1011, dev=0x0024, revid=0x03
bus=0, slot=20, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0xff (7650 ns), mingnt=0x20 (8000 ns), maxlat=0x00 (0 ns)
dc0: <Intel 21143 10/100BaseTX> port 0x9000-0x907f mem 0x81181000-0x8118107f irq 0 at device 3.0 on pci0
dc0: Ethernet address: 08:00:2b:86:85:93
miibus0: <MII bus> on dc0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc0: bpf attached
dc0: interrupting at CIA irq 0
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Cypress 82C693 ATA controller> port 0x90a0-0x90af,0x3f4-0x3f7,0x1f0-0x1f7 irq 238 at device 7.1 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=01
ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0-slave: stat=0x00 err=0x04 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: interrupting at ISA irq 14
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: interrupting at ISA irq 15
ata1: [MPSAFE]
atapci1: <GENERIC ATA controller> port 0x374-0x377,0x170-0x177 mem 0x81170000-0x8117ffff irq 239 at device 7.2 on pci0
atapci1: unable to map interrupt
ohci0: <OHCI (generic) USB controller> mem 0x81180000-0x81180fff irq 234 at device 7.3 on pci0
ohci0: (New OHCI DeviceId=0xc6931080)
ohci0: interrupting at ISA irq 10
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1080) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <display, VGA> at device 12.0 (no driver attached)
pcib1: <PCI-PCI bridge> at device 20.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 0
pcib1: I/O decode 0x8000-0x8fff
pcib1: memory decode 0x81000000-0x810fffff
pcib1: prefetched decode 0xfff00000-0xfffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 4, range 32, base 00008000, size 8, enabled
map[14]: type 1, range 32, base 81010000, size 12, enabled
found-> vendor=0x1077, dev=0x1020, revid=0x05
bus=1, slot=4, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0047, statreg=0x0200, cachelnsz=16 (dwords)
lattimer=0xf8 (7440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=3
Qlogic ISP Driver, FreeBSD Version 5.9, Core Version 2.7
isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x8000-0x80ff mem 0x81010000-0x81010fff irq 3 at device 4.0 on pci1
pcib1: device isp0 requested decoded memory range 0x81010000-0x81010fff
isp0: using Memory space register mapping
isp0: interrupting at CIA irq 3
isp0: Ultra Mode Capable
isp0: Board Type 1040B, Chip Revision 0x5, loaded F/W Revision 4.66.0
isp0: Last F/W revision was 5.57.1
isp0: 243 max I/O commands supported
isp0: Initiator ID is 7 on Channel 0
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
atkbd: the current kbd controller command byte 0003
atkbd: keyboard ID 0x83ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000
atkbd0: interrupting at ISA irq 1
psm0: current command byte:0043
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 1a 03 c8
psm: status 1a 03 c8
psm: status 1a 03 c8
psm: data 08 00 00
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: interrupting at ISA irq 12
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:08, syncbits:08
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: interrupting at ISA irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
Calibrating clock(s) ... PCC clock: 499869078 Hz (firmware 500000000 Hz)
i8254 clock: 1191057 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
ppc0: using extended I/O port range
ppc0: <Parallel port> failed to probe at port 0x3bc-0x3c3 irq 7 on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x0>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A, console
sio0: interrupting at ISA irq 4
sio1: irq maps: 0x1 0x9 0x1 0x1
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio1: interrupting at ISA irq 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xb8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 6f 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 6f 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
sbc0: <ESS ES1888> at port 0x220-0x22f irq 5 drq 1 on isa0
sbc0: interrupting at ISA irq 5
pcm0: <ESS 18xx DSP> on sbc0
pcm0: ESS0 detected
pcm0: sndbuf_setmap 40b52000, 1000; 0xfffffe0008b6e000 -> b52000
pcm0: sndbuf_setmap 40b54000, 1000; 0xfffffe0008b70000 -> b54000
isa_probe_children: probing PnP devices
procfs registered
Timecounter "i8254" frequency 1193182 Hz quality 0
Timecounter "alpha" frequency 499869078 Hz quality 0
Timecounters tick every 0.976 msec
lo0: bpf attached
ata0-master: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin
acd0: <Compaq CRD-8322B/1.07> CDROM drive at ata0 as master
acd0: read 5500KB/s (5500KB/s), 128KB buffer, BIOSPIO
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked, lock protected
acd0: Medium: no/blank disc
Waiting 5 seconds for SCSI devices to settle
isp0: driver initiated bus reset of bus 0
(probe0:isp0:0:0:0): Retrying Command
(probe1:isp0:0:1:0): Retrying Command
(probe6:isp0:0:6:0): Retrying Command
(probe9:isp0:0:10:0): Retrying Command
GEOM: create disk da0 dp=0xfffffc0000b7e068
GEOM: create disk da1 dp=0xfffffc000b957c68
GEOM: create disk da2 dp=0xfffffc0000b7d468
GEOM: create disk da3 dp=0xfffffc0000b7ac68
pass0 at isp0 bus 0 target 0 lun 0
pass0: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
pass0: Serial Number RDHX1052
GEOM: new disk da0
GEOM: new disk da1
GEOM: new disk da2
GEOM: new disk da3
pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
pass1 at isp0 bus 0 target 1 lun 0
pass1: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
pass1: Serial Number QD731971
pass1: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
pass2 at isp0 bus 0 target 5 lun 0
pass2: <DEC TLZ10 (C) DEC 04a8> Removable Sequential Access SCSI-2 device
pass2: Serial Number 0005210745
pass2: 10.000MB/s transfers (10.000MHz, offset 8)
pass3 at isp0 bus 0 target 6 lun 0
pass3: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
pass3: Serial Number RDHZ7101
pass3: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
pass4 at isp0 bus 0 target 10 lun 0
pass4: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
pass4: Serial Number RD3B5869
pass4: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
sa0 at isp0 bus 0 target 5 lun 0
sa0: <DEC TLZ10 (C) DEC 04a8> Removable Sequential Access SCSI-2 device
sa0: Serial Number 0005210745
sa0: 10.000MB/s transfers (10.000MHz, offset 8)
da0 at isp0 bus 0 target 0 lun 0
da0: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da0: Serial Number RDHX1052
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
da1 at isp0 bus 0 target 1 lun 0
da1: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da1: Serial Number QD731971
da1: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da1: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
da2 at isp0 bus 0 target 6 lun 0
da2: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da2: Serial Number RDHZ7101
da2: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da2: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
da3 at isp0 bus 0 target 10 lun 0
da3: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da3: Serial Number RD3B5869
da3: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da3: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
GEOM: Configure da0a, start 0 length 268435456 end 268435455
GEOM: Configure da0b, start 268435456 length 536870912 end 805306367
GEOM: Configure da0c, start 0 length 4569600000 end 4569599999
GEOM: Configure da0e, start 805306368 length 157286400 end 962592767
GEOM: Configure da0f, start 962592768 length 536870912 end 1499463679
GEOM: Configure da0g, start 1499463680 length 262144000 end 1761607679
GEOM: Configure da0h, start 1761607680 length 2807992320 end 4569599999
GEOM: Configure da1c, start 0 length 4569600000 end 4569599999
GEOM: Configure da1e, start 0 length 4569600000 end 4569599999
GEOM: Configure da2c, start 0 length 4569600000 end 4569599999
GEOM: Configure da2e, start 0 length 4569600000 end 4569599999
GEOM: Configure da3a, start 8192 length 4569591808 end 4569599999
GEOM: Configure da3c, start 0 length 4569600000 end 4569599999
Mounting root from ufs:/dev/da0a
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?424472EF.4CC4B62C>