Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 10 Jun 2009 16:40:36 +0200
From:      Andre Oppermann <andre@freebsd.org>
To:        Mike Tancsa <mike@sentex.net>
Cc:        scottl@freebsd.org, freebsd-stable@freebsd.org
Subject:   Re: (probe23:arcmsr0:0:16:0): inquiry data fails comparison at DV1 step
Message-ID:  <4A2FC5E4.3000909@freebsd.org>
In-Reply-To: <200906101321.n5ADLbds031697@lava.sentex.ca>
References:  <4A2FA4EF.5060603@freebsd.org> <200906101321.n5ADLbds031697@lava.sentex.ca>

next in thread | previous in thread | raw e-mail | index | archive | help
Mike Tancsa wrote:
> At 08:19 AM 6/10/2009, Andre Oppermann wrote:
>> Today I upgraded an AMD64 server from FreeBSD 6.4 to 7-STABLE and got 
>> a big
>> nasty surprise with the Areca RAID controller:
>>
>> arcmsr0: <Areca SATA Host Adapter RAID Controller (RAID6 capable)
>> > mem 0xfdbff000-0xfdb400000 irq16 at device 14.0 on pci18
>> ARECA RAID ADAPTER0: Driver Version 1.20.00.15 2007-10-07
>> ARECA RAID ADAPTER0: FIRMWARE VERSION V1.46 2009-01-06
>> arcmsr0: [ITHREAD]
>> ...
>> (probe23:arcmsr0:0:16:0): inquiry data fails comparison at DV1 step
>> run_interrupt_driven_hooks: still waiting after 60 seconds for xpt_config
> 
> 
> Not sure if its a firmware issue or not, but I am running an AMD64 
> RELENG_7 kernel from Apr 23 and its works fine.  The DV1 error seems 
> "normal" in that I get it as well. I dont boot off the controller, so 
> not sure if thats part of the issue or not.

I did an firmware update after I encountered the issue the first time.
Before it was V1.43. Exactly the same behavior.

And yes, I do have to boot off the RAID. After the run_interrupt_driven_hooks
everything hangs and no daX drives are ever detected.  You don't seem to get
this particular error.

-- 
Andre

> arcmsr0: <Areca SATA Host Adapter RAID Controller
>  > mem 0xea600000-0xea600fff irq 18 at device 14.0 on pci3
> ARECA RAID ADAPTER0: Driver Version 1.20.00.15 2007-10-07
> ARECA RAID ADAPTER0: FIRMWARE VERSION V1.44 2008-2-1
> arcmsr0: [ITHREAD]
> 
> (probe48:arcmsr0:0:16:0): inquiry data fails comparison at DV1 step
> da1 at arcmsr0 bus 0 target 0 lun 0
> da1: <Areca usrvar R001> Fixed Direct Access SCSI-5 device
> da1: 166.666MB/s transfers (83.333MHz DT, offset 32, 16bit)
> da1: Command Queueing Enabled
> da1: 76293MB (156249600 512 byte sectors: 255H 63S/T 9726C)
> da0 at twa0 bus 0 target 0 lun 0
> da0: <AMCC 9650SE-2LP DISK 3.08> Fixed Direct Access SCSI-5 device
> da0: 100.000MB/s transfers
> da0: 66747MB (136697856 512 byte sectors: 255H 63S/T 8509C)
> da2 at arcmsr0 bus 0 target 0 lun 1
> da2: <Areca backup1 R001> Fixed Direct Access SCSI-5 device
> da2: 166.666MB/s transfers (83.333MHz DT, offset 32, 16bit)
> da2: Command Queueing Enabled
> da2: 2784728MB (5703123456 512 byte sectors: 255H 63S/T 355003C)




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4A2FC5E4.3000909>