Date: Sun, 23 Aug 2009 22:52:34 -0500 From: Guillermo Paredes - EDDAS <gparedes@eddas.com.pe> Cc: freebsd-usb@freebsd.org Subject: Re: Huawei E169 USB 3G Modem not detected as modem in 7.2 Message-ID: <1a008f20908232052o13438dbfn34634ae77f1ea221@mail.gmail.com> In-Reply-To: <24C44DD8-EA6D-448C-B610-EB4EAB561CBB@yahoo.it> References: <5B4090AC-F8B3-4AAF-8501-FEAFE087EBCE@yahoo.it> <200908240044.n7O0iXAe041209@lava.sentex.ca> <24C44DD8-EA6D-448C-B610-EB4EAB561CBB@yahoo.it>
next in thread | previous in thread | raw e-mail | index | archive | help
Gianni if you see the u3g.c file o the sources just only appear the Huawei E220, i see in other maillist some like add the device id in this file to add the E226 Model, maybe if you can do the same with your model. for other way, the ucom driver dont load the device if the umass driver is loaded, this happend in freebsd70 with the md300 of Sony Ericsson. Best Regards 2009/8/23 Gianni <gdoe6545@yahoo.it> > > On 24/ago/09, at 02:47, Mike Tancsa wrote: > > At 08:05 AM 8/23/2009, Gianni wrote: >> >>> I've seen a few posts related to the Huawei E169 3G modem which have >>> reported this device as working under 7.2. I have the u3g driver >>> loaded but the modem is only recognised as umass, I tried disabling >>> umass and the device came up as ugen. >>> My 7.2-STABLE is newly built today, log messages below, should this >>> modem work out of the box or is there some extra configuration needed? >>> Any suggestion much appreciated. >>> >> >> >> Make sure umass is loaded as well as the u3g driver. Then, after all has >> booted up, try >> usbdevs -v >> camcontrol eject pass0 >> usbdevs >> >> Some devices need that to put them into 'modem mode'... If it works, you >> should see /dev/cuaU0.0 and you should see a differences in the output of >> usbdevs before and after the camcontrol eject pass0 >> >> ---Mike >> > > Thanks Mike, unfortunately that did not work, the /dev/cuaU0.0 device did > not appear. > -Gianni > > nicknack# usbdevs -v > Controller /dev/usb0: > addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), > Intel(0x0000), rev 1.00 > port 1 powered > port 2 powered > Controller /dev/usb1: > addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), > Intel(0x0000), rev 1.00 > port 1 powered > port 2 powered > Controller /dev/usb2: > addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), > Intel(0x0000), rev 1.00 > port 1 powered > port 2 powered > Controller /dev/usb3: > addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), > Intel(0x0000), rev 1.00 > port 1 powered > port 2 powered > Controller /dev/usb4: > addr 1: high speed, self powered, config 1, EHCI root hub(0x0000), > Intel(0x0000), rev 1.00 > port 1 powered > port 2 addr 3: high speed, self powered, config 1, HUAWEI Mobile(0x1446), > HUAWEI Technology(0x12d1), rev 0.00 > port 3 powered > port 4 powered > port 5 powered > port 6 addr 2: high speed, power 500 mA, config 1, USB2.0-CRW(0x0158), > Generic(0x0bda), rev 58.87 > port 7 powered > port 8 powered > nicknack# camcontrol eject pass0 > Unit stopped successfully, Media ejected > nicknack# usbdevs -v > Controller /dev/usb0: > addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), > Intel(0x0000), rev 1.00 > port 1 powered > port 2 powered > Controller /dev/usb1: > addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), > Intel(0x0000), rev 1.00 > port 1 powered > port 2 powered > Controller /dev/usb2: > addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), > Intel(0x0000), rev 1.00 > port 1 powered > port 2 powered > Controller /dev/usb3: > addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), > Intel(0x0000), rev 1.00 > port 1 powered > port 2 powered > Controller /dev/usb4: > addr 1: high speed, self powered, config 1, EHCI root hub(0x0000), > Intel(0x0000), rev 1.00 > port 1 powered > port 2 addr 3: high speed, self powered, config 1, HUAWEI Mobile(0x1446), > HUAWEI Technology(0x12d1), rev 0.00 > port 3 powered > port 4 powered > port 5 powered > port 6 addr 2: high speed, power 500 mA, config 1, USB2.0-CRW(0x0158), > Generic(0x0bda), rev 58.87 > port 7 powered > port 8 powered > > > _______________________________________________ > freebsd-usb@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-usb > To unsubscribe, send any mail to "freebsd-usb-unsubscribe@freebsd.org" > -- Guillermo Paredes Cornejo - EDDAS MAIL gparedes@eddas.com.pe TEL +51[1]6135929 x 311 +51[54]959177611 (RPC Claro) +51[54]959592141 (Movistar) RPM *374564 VoIP sip:311@eddas.com.pe <sip%3A311@eddas.com.pe> WWW www.eddas.com.pe
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1a008f20908232052o13438dbfn34634ae77f1ea221>