Skip site navigation (1)Skip section navigation (2)
Date:      Sun, 03 Feb 2008 17:08:16 -0500
From:      Jeff Palmer <jpalmer@totaldiver.net>
To:        Wael Nasreddine <mla@nasreddine.com>
Cc:        hardware@freebsd.org
Subject:   Re: I need some help trying to make Intel 3945ABG wireless card working.
Message-ID:  <47A63B50.6010104@totaldiver.net>
In-Reply-To: <d3328e7b0802031114m50f8d543x4f62e920c65fe0f7@mail.gmail.com>
References:  <d3328e7b0802031007k2bec0e14l49ebfdc60db0b123@mail.gmail.com>	 <47A60DA2.60200@totaldiver.net> <d3328e7b0802031114m50f8d543x4f62e920c65fe0f7@mail.gmail.com>

next in thread | previous in thread | raw e-mail | index | archive | help
Wael Nasreddine wrote:
> On Feb 3, 2008 7:53 PM, Jeff Palmer <jpalmer@totaldiver.net> wrote:
>   
>> Wael Nasreddine wrote:
>>     
>>> -----BEGIN PGP SIGNED MESSAGE-----
>>> Hash: SHA1
>>>
>>> Hello,
>>>
>>> I'm new to FreeBSD and I have a Toshiba Satellite A135-S4427 equipped
>>> with an Intel 3945ABG wireless card. I searched a bit and I added
>>> these to /boot/loader.conf
>>> - ----CUT
>>> if_wpi_load="YES"
>>> wlan_load="YES"
>>> wlan_amrr_load="YES"
>>> firmware_load="YES"
>>> wpifw_load="YES"
>>> - ----CUT
>>>
>>> Now I have a wpi0 interface I tried doing
>>> - ----CUT
>>> ifconfig wpi0 ssid eMxyzptlk wepkey "0xC1C731EA92AC05B1E7BA6186CF"
>>> - ----CUT
>>>
>>> but it doesn't associate with the AP all I see in ifconfig is
>>> - ----CUT
>>> wpi0: flags=8802
>>>  metric 0 mtu 1500
>>>     ether 00:19:d2:42:91:3f
>>>     media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
>>>     status: no carrier
>>>     ssid eMxyzptlk channel 1 (2412 Mhz 11b)
>>>     authmode OPEN privacy OFF wepkey 1:104-bit txpower 50 bmiss 7
>>>     scanvalid 60 bintval 0
>>> - ----CUT
>>>
>>> my AP is channel 11 so tried to switch manually
>>> - ----CUT
>>> ifconfig wpi0 ssid eMxyzptlk wepkey "0xC1C731EA92AC05B1E7BA6186CF" channel 11
>>> - ----CUT
>>> but it didn't associate this way either
>>>
>>> - ----CUT
>>> wpi0: flags=8802
>>>  metric 0 mtu 1500
>>>     ether 00:19:d2:42:91:3f
>>>     media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
>>>     status: no carrier
>>>     ssid eMxyzptlk channel 11 (2462 Mhz 11g)
>>>     authmode OPEN privacy OFF wepkey 1:104-bit txpower 50 bmiss 7
>>>     scanvalid 60 protmode CTS bintval 0
>>> - ----CUT
>>>
>>> I don't know where to go from here, I appreciate your help guys
>>>
>>> Thanks.
>>>
>>> - --
>>> Wael Nasreddine
>>> http://wael.nasreddine.com
>>> PGP: 1024D/C8DD18A2 06F6 1622 4BC8 4CEB D724  DE12 5565 3945 C8DD 18A2
>>>
>>> .: An infinite number of monkeys typing into GNU emacs,
>>>    would never make a good program. (L. Torvalds 1995) :.
>>>
>>> -----BEGIN PGP SIGNATURE-----
>>> Version: GnuPG v2.0.4 (FreeBSD)
>>>
>>> iD8DBQFHpgLEVWU5RcjdGKIRAiOWAJ9FNxOgy4DrLhi0acswvdefP5m3QwCg3qt8
>>> lqR0npPnfg7V4/XJavhNH/Y=
>>> =PKGu
>>> -----END PGP SIGNATURE-----
>>> _______________________________________________
>>> freebsd-hardware@freebsd.org mailing list
>>> http://lists.freebsd.org/mailman/listinfo/freebsd-hardware
>>> To unsubscribe, send any mail to "freebsd-hardware-unsubscribe@freebsd.org"
>>>
>>>
>>>       
>> Wael,
>>
>> you didn't mention what version of the driver you are using,  so I'll
>> assume you're using the one in 7.0-RC1.  To make you aware,  I have a
>> toshiba satellite A135-S4517, and the wpi driver included in RELENG_7_0
>> doesn't work for me either.
>>     
> Yes I do have the one Included in 7.0-RC1
>
>   
>> Attempts to work through the issue with the person originally porting
>> the driver seem to have stalled, but in following current@ it seems as
>> though others are submitting patches for it recently.
>>
>> My advice?   Hang in there.  at some point the hardware will be
>> supported.  It seems to work for several implementations of th 3945abg
>> chipset.  I can't assume ours is that drastically different.
>>
>> Jeff
>>
>>
>>     
> Oh that's too bad :( Hopefully it'll be soon.
> What about your Texas Intruments MMC/SD reader? I haven't tried mine
> yet is it working on yours??
>
>
>   
Wael,  the MMC/SD does not currently work.  Last I heard, imp@ was going 
to work on it a driver.   further info:  http://bsdimp.blogspot.com/

Hope it helps,

Jeff Palmer



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?47A63B50.6010104>