Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 07 Dec 2006 17:44:43 -0500
From:      Joe Marcus Clarke <marcus@FreeBSD.org>
To:        current@FreeBSD.org
Subject:   Problem with gif and IPv6 in -CURRENT
Message-ID:  <4578995B.4090305@FreeBSD.org>

next in thread | raw e-mail | index | archive | help
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

I am running:

FreeBSD jclarke-pc 7.0-CURRENT FreeBSD 7.0-CURRENT #81: Thu Dec  7
16:06:32 EST 2006     marcus@jclarke-pc:/usr/obj/usr/src/sys/JCLARKE-PC
 i386

And I am trying to get a gif IPv6 tunnel up to a Cisco router.  I can
get this to work on a 6.2-PRERELEASE server, but the -CURRENT machine
always claims there is no route to the far end of the point-to-point
link.  Here is my config:

# ifconfig gif0 create
# ifconfig gif0 tunnel 172.18.173.17 10.29.100.75
# ifconfig gif0 inet6 3ffe:604::2 3ffe:604::1 prefixlen 128
# ifconfig gi0
gif0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1280
        tunnel inet 172.18.173.17 --> 10.29.100.75
        inet6 fe80::211:11ff:fe10:461e%gif0 prefixlen 64 scopeid 0x4
        inet6 3ffe:604::2 --> 3ffe:604::1 prefixlen 128

This looks good, and I can ping my local 3ffe:604::2 address.  However,
when I ping 3ffe:604::1, I get:

ping6: UDP connect: No route to host

It's not lying.  I don't have a route to 3ffe:604::1:

# netstat -nr
...
::/96                             ::1                           UGRS
    lo0
::1                               ::1                           UHL
    lo0
::ffff:0.0.0.0/96                 ::1                           UGRS
    lo0
2003:a02::/64                     link#1                        UC
    em0
2003:a02::1                       00:11:11:10:46:1e             UHL
    lo0
3ffe:604::2                       link#4                        UHL
    lo0
fe80::/10                         ::1                           UGRS
    lo0
fe80::%em0/64                     link#1                        UC
    em0
fe80::211:11ff:fe10:461e%em0      00:11:11:10:46:1e             UHL
    lo0
fe80::%lo0/64                     fe80::1%lo0                   U
    lo0
fe80::1%lo0                       link#3                        UHL
    lo0
fe80::%gif0/64                    link#4                        UC
   gif0
fe80::211:11ff:fe10:461e%gif0     link#4                        UHL
    lo0
ff01:1::/32                       link#1                        UC
    em0
ff01:3::/32                       ::1                           UC
    lo0
ff01:4::/32                       link#4                        UC
   gif0
ff02::/16                         ::1                           UGRS
    lo0
ff02::%em0/32                     link#1                        UC
    em0
ff02::%lo0/32                     ::1                           UC
    lo0
ff02::%gif0/32                    link#4                        UC
   gif0

The IPv4 address on the other end of the tunnel is reachable, and the
Cisco router has no problems finding a route to the FreeBSD machine.
Here is the config from the Cisco side:

interface Tunnel1
 no ip address
 load-interval 30
 ipv6 address 3FFE:604::1/126
 ipv6 enable
 tunnel source 10.29.100.75
 tunnel destination 172.18.173.17
 tunnel mode ipv6ip

Why isn't the other end of the point-to-point tunnel being instantiated
in the routing table?  If I take this exact config to a 6.2 box, this
works just fine, and the far end of the PTP link is instantiated in the
routing table.  Thanks for any clues you can provide.

Joe

- --
Joe Marcus Clarke
FreeBSD GNOME Team	::	gnome@FreeBSD.org
FreeNode / #freebsd-gnome
http://www.FreeBSD.org/gnome
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (Darwin)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org

iD8DBQFFeJlbb2iPiv4Uz4cRAhoxAJ0ZShVGN2sEkNh0IAomPr/DeUBNdwCgo7bw
eSeAc+c1Pc+qBCBWdF0VvtQ=
=hYOr
-----END PGP SIGNATURE-----



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4578995B.4090305>