Date: Sun, 20 Apr 2014 23:31:26 +0400 From: Andrey Fesenko <f0andrey@gmail.com> To: freebsd-current <freebsd-current@freebsd.org>, "freebsd-hackers@freebsd.org" <freebsd-hackers@freebsd.org>, mav@freebsd.org Subject: Re: SATA2 mode on SATA3 SSD (marvell controller) after boot Message-ID: <CA%2BK5SrPN3iRK19exw0ADWBhzG2qP3nzNpGRg-guYqUhJZexcQg@mail.gmail.com> In-Reply-To: <CA%2BK5SrO0rAWP5Ca_HNBYUE-bGgsuVxvaFOnmrMoCoWVGwbZY3A@mail.gmail.com> References: <CA%2BK5SrO0rAWP5Ca_HNBYUE-bGgsuVxvaFOnmrMoCoWVGwbZY3A@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, Apr 17, 2014 at 2:10 PM, Andrey Fesenko <f0andrey@gmail.com> wrote: > if disconnect ssd > pr 17 14:07:08 desktop kernel: ahcich3: DISCONNECT requested > Apr 17 14:07:08 desktop kernel: ahcich3: AHCI reset... > Apr 17 14:07:08 desktop kernel: ahcich3: SATA connect timeout > time=10000us status=00000000 > Apr 17 14:07:08 desktop kernel: ahcich3: AHCI reset: device not found > Apr 17 14:07:08 desktop kernel: pass3 at ahcich3 bus 0 scbus3 target 0 lun 0 > Apr 17 14:07:08 desktop kernel: pass3: <PLEXTOR PX-128M5S 1.05> s/n > P02411112921 detached > Apr 17 14:07:08 desktop kernel: ada3 at ahcich3 bus 0 scbus3 target 0 lun 0 > Apr 17 14:07:08 desktop kernel: ada3: <PLEXTOR PX-128M5S 1.05> s/n > P02411112921 detached > Apr 17 14:07:08 desktop kernel: (pass3:ahcich3:0:0:0): Periph destroyed > Apr 17 14:07:08 desktop kernel: (ada3:ahcich3:0:0:0): Periph destroyed > Apr 17 14:07:18 desktop kernel: ahcich3: CONNECT requested > Apr 17 14:07:18 desktop kernel: ahcich3: AHCI reset... > Apr 17 14:07:18 desktop kernel: ahcich3: SATA connect time=8000us > status=00000133 > Apr 17 14:07:18 desktop kernel: ahcich3: AHCI reset: device found > Apr 17 14:07:18 desktop kernel: ahcich3: AHCI reset: device ready after 0ms > Apr 17 14:07:18 desktop kernel: ada3 at ahcich3 bus 0 scbus3 target 0 lun 0 > Apr 17 14:07:18 desktop kernel: GEOM: new disk ada3 > Apr 17 14:07:18 desktop kernel: ada3: <PLEXTOR PX-128M5S 1.05> ATA-8 > SATA 3.x device > Apr 17 14:07:18 desktop kernel: ada3: Serial Number P02411112921 > Apr 17 14:07:18 desktop kernel: ada3: 600.000MB/s transfers (SATA 3.x, > UDMA6, PIO 8192bytes) > Apr 17 14:07:18 desktop kernel: ada3: Command Queueing enabled > Apr 17 14:07:18 desktop kernel: ada3: 122104MB (250069680 512 byte > sectors: 16H 63S/T 16383C) > Apr 17 14:07:18 desktop kernel: ada3: Previously was known as ad10 > Apr 17 14:07:18 desktop kernel: pass3 at ahcich3 bus 0 scbus3 target 0 lun 0 > Apr 17 14:07:18 desktop kernel: pass3: <PLEXTOR PX-128M5S 1.05> ATA-8 > SATA 3.x device > Apr 17 14:07:18 desktop kernel: pass3: Serial Number P02411112921 > Apr 17 14:07:18 desktop kernel: pass3: 600.000MB/s transfers (SATA > 3.x, UDMA6, PIO 8192bytes) > Apr 17 14:07:18 desktop kernel: pass3: Command Queueing enabled > > > # uname -a > FreeBSD desktop.local 11.0-CURRENT FreeBSD 11.0-CURRENT #0 r263932: > Sun Mar 30 15:43:01 MSK 2014 > root@desktop.local:/usr/obj/usr/src/sys/MY_DES amd64 Is it possible camcontrol repeat behavior as physical disable/enable or enable SATA 3.x mode? camcontrol negotiate only report not set new mode. # camcontrol negotiate pass2 Current parameters: (pass2:ahcich3:0:0:0): SATA revision: 2.x (pass2:ahcich3:0:0:0): ATA mode: UDMA6 (pass2:ahcich3:0:0:0): ATAPI packet length: 0 (pass2:ahcich3:0:0:0): PIO transaction length: 8192 (pass2:ahcich3:0:0:0): PMP presence: 0 (pass2:ahcich3:0:0:0): Number of tags: 32 (pass2:ahcich3:0:0:0): SATA capabilities: 00000030 (pass2:ahcich3:0:0:0): tagged queueing: enabled
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CA%2BK5SrPN3iRK19exw0ADWBhzG2qP3nzNpGRg-guYqUhJZexcQg>