Date: Sat, 12 Feb 2000 11:21:18 -0800 From: Mike Smith <msmith@freebsd.org> To: Jesper Skriver <jesper@skriver.dk> Cc: mobile@FreeBSD.org Subject: Re: Support for Eicon Diva Pro ISDN pccard adapter Message-ID: <200002121921.LAA04520@mass.cdrom.com> In-Reply-To: Your message of "Sat, 12 Feb 2000 20:01:05 %2B0100." <20000212200105.A36317@skriver.dk>
next in thread | previous in thread | raw e-mail | index | archive | help
> Hi, > > Does anyone have any idea of how to get such a thing to work (in > -current) ? > > I assume it's just a serial port to the system, but the below says > > Tuple #4, code = 0x21 (Functional ID), length = 2 > 000: 06 00 > Network/LAN adapter > > I don't know is this means, that it's not a serial port, or ? That's correct. > pccardc dumpcis: The information here is probably not enough for our braindead pccard code to get it right; with no configuration entries it won't be able to guesstimate a valid configuration. It's impossible to tell from this whether the card does or doesn't look like a serial port; I'd say more likely not though (it has 16 I/O registers, rather than the 8 that a standard UART has). > Configuration data for card in slot 1 > Tuple #1, code = 0x1 (Common memory descriptor), length = 3 > 000: 00 00 ff > Common memory device information: > Device number 1, type No device, WPS = OFF > Speed = No speed, Memory block size = 512b, 1 units > Tuple #2, code = 0x15 (Version 1 info), length = 37 > 000: 01 04 45 69 63 6f 6e 20 44 69 65 68 6c 00 44 69 > 010: 76 61 20 50 72 6f 00 30 35 2e 30 33 2e 39 36 00 > 020: 31 2d 31 00 ff > Version = 1.4, Manuf = [Eicon Diehl],card vers = [Diva Pro] > Addit. info = [05.03.96],[1-1] > Tuple #3, code = 0x20 (Manufacturer ID), length = 4 > 000: 21 01 32 20 > PCMCIA ID = 0x121, OEM ID = 0x2032 > Tuple #4, code = 0x21 (Functional ID), length = 2 > 000: 06 00 > Network/LAN adapter > Tuple #5, code = 0x1a (Configuration map), length = 6 > 000: 01 01 c0 00 01 ff > Reg len = 2, config register addr = 0xc0, last config = 0x1 > Registers: X------- > Tuple #6, code = 0x1b (Configuration entry), length = 12 > 000: c1 81 19 71 55 7d 7d 7d 44 30 ff ff > Config index = 0x1(default) > Interface byte = 0x81 (I/O) wait signal supported > Vcc pwr: > Nominal operating supply voltage: 5 x 1V > Max current average over 1 second: 9 x 10mA > Max current average over 10 ms: 9 x 10mA > Power down supply current: 9 x 10mA > Card decodes 4 address lines, limited 8/16 Bit I/O > IRQ modes: Pulse > IRQ level = 4 > Tuple #7, code = 0x14 (No link), length = 0 > Tuple #8, code = 0xff (Terminator), length = 0 > > > /Jesper > > -- > Jesper Skriver, jesper(at)skriver(dot)dk - CCIE #5456 > Work: Network manager @ AS3292 (Tele Danmark DataNetworks) > Private: Geek @ AS2109 (A much smaller network ;-) > > One Unix to rule them all, One Resolver to find them, > One IP to bring them all and in the zone to bind them. > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-mobile" in the body of the message > -- \\ Give a man a fish, and you feed him for a day. \\ Mike Smith \\ Tell him he should learn how to fish himself, \\ msmith@freebsd.org \\ and he'll hate you for a lifetime. \\ msmith@cdrom.com To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200002121921.LAA04520>