Date: Sat, 22 Jul 2000 13:16:49 -0700 From: "David O'Brien" <obrien@FreeBSD.ORG> To: Matthew Jacob <mjacob@feral.com> Cc: alpha@FreeBSD.ORG Subject: Re: 4.1-20000719-RC#2 Message-ID: <20000722131648.E44856@dragon.nuxi.com> In-Reply-To: <Pine.BSF.4.05.10007211228120.8451-100000@semuta.feral.com>; from mjacob@feral.com on Fri, Jul 21, 2000 at 12:30:00PM -0700 References: <14712.41758.459790.390526@grasshopper.cs.duke.edu> <Pine.BSF.4.05.10007211228120.8451-100000@semuta.feral.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, Jul 21, 2000 at 12:30:00PM -0700, Matthew Jacob wrote: > I think you need to put into RELNOTES that Alpha 4100 isn't supported. More testing. Using the CDROM that boots fine on my Miata(MX5) on the 4100, I find that the CDROM isn't accessable from the loader. Even doing an ``ls'' from the loader hangs. Note that this has always worked on my Miata (even with the current /boot/cdboot rather than the 4.0-R one). This behavior seems the same with floppies. So for some reason the loader is unable to access any of our bits from the installation media [in the non-harddisk case]. P00>>>boot dka500 Initializing... SROM V2.0 on cpu0 SROM V2.0 on cpu1 XSROM V5.3 on cpu0 XSROM V5.3 on cpu1 BCache testing complete on cpu0 BCache testing complete on cpu1 mem_pair0 - 512 MB 20..20..21..21..23.. please wait 12 seconds for T24 to complete 24..24.. Memory testing complete on cpu1 Memory testing complete on cpu0 starting console on CPU 0 sizing memory 0 512 MB EDO starting console on CPU 1 probing IOD1 hose 1 bus 0 slot 1 - NCR 53C810 bus 0 slot 2 - DECchip 21140-AA probing IOD0 hose 0 bus 0 slot 1 - PCEB probing EISA Bridge, bus 1 bus 0 slot 2 - S3 Trio64/Trio32 bus 0 slot 4 - PCI-PCI Bridge probing PCI-PCI Bridge, bus 2 bus 2 slot 0 - QLogic ISP1020 ** keyboard error ** configuring I/O adapters... ncr0, hose 1, bus 0, slot 1 tulip0, hose 1, bus 0, slot 2 floppy0, hose 0, bus 1, slot 0 isp0, hose 0, bus 2, slot 0 System temperature is 30 degrees C AlphaServer 4100 Console V5.3-1, 27-OCT-1998 11:16:38 CPU 0 booting (boot dka500.5.0.1.1) block 0 of dka500.5.0.1.1 is a valid boot block reading 356 blocks from dka500.5.0.1.1 bootstrap code read in Building FRU table base = 200000, image_start = 0, image_bytes = 2c800 initializing HWRPB at 2000 initializing page table at 1f2000 initializing machine state setting affinity to the primary CPU jumping to bootstrap code Console: SRM firmware console VMS PAL rev: 0x4001200010113 OSF PAL rev: 0x4001a00020115 Switch to OSF PAL code succeeded. FreeBSD/alpha SRM CD9660 boot, Revision 0.1 (jkh@beast.freebsd.org, Mon Mar 20 21:08:56 GMT 2000) Memory: 524288 k > echo \007\007 > autoboot 10 Hit [Enter] to boot immediately, or any other key for command prompt. Booting [kernel] in 6 seconds... Type '?' for a list of commands, 'help' for more detailed help. ok ls -l <HANGS for minutes> failed to send Read to dka500.5.0.1.1 halt code = 7 pcb 0 !!! Console entry context is not valid - Reset the system !!! Brk 0 at 0006621C 0006621C ! BPT To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000722131648.E44856>