Date: Tue, 23 Feb 1999 16:27:52 -0500 (EST) From: Andrew Gallatin <gallatin@cs.duke.edu> To: "Justin T. Gibbs" <gibbs@plutotech.com> Cc: scsi@FreeBSD.org Subject: Re: dual-channel U2W scsi performance Message-ID: <14035.5458.71518.652907@grasshopper.cs.duke.edu> In-Reply-To: <199902232020.NAA13242@pluto.plutotech.com> References: <14034.65025.537279.428755@grasshopper.cs.duke.edu> <199902232020.NAA13242@pluto.plutotech.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Justin T. Gibbs writes: > > There must be something wrong with your cables. I've had several instances > where a loose connector pin caused intermittent parity-errors. If both > the driver and the end device are reporting errors, they can't be wrong. > I've tested SE operation on the aic7896, so I know that it can work > with the current driver. Before I turned off parity in scsi-select, I tried all possible combinations of cabling (my setup is motherboard connecter -> internal cable -> external connector-> external cable -> box w/2 4G cheetahs -> active terminator), I switched out both cables, the external connector, the terminator & the box w/2 cheetahs.. No combination worked on the second channel. All combinations worked on the first channel. (by worked, I mean probed w/o parity errors) > One other thing that may be interesting is a dmesg from a -v boot. It > could be that the driver is not setting the termination properly, but > this is fairly straight forward for the aic789X series. Here you go. My message buffer isn't quite big enough, so I've captured the serial console output for you. The last bits (after the login prompt) are from <4:23pm>scone/gallatin:~>sudo disklabel -wr da0 auto disklabel: write: Input/output error Thanks, Drew ------------------------------------------------------------------------------ Andrew Gallatin, Sr Systems Programmer http://www.cs.duke.edu/~gallatin Duke University Email: gallatin@cs.duke.edu Department of Computer Science Phone: (919) 660-6590 BIOS basemem (639K) != RTC basemem (640K), setting to BIOS value Copyright (c) 1992-1999 FreeBSD Inc. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. FreeBSD 4.0-CURRENT #4: Sat Feb 20 11:51:17 EST 1999 gallatin@grasshopper.cs.duke.edu:/freebsd/src/sys/compile/TPZ Calibrating clock(s) ... TSC clock: 450981231 Hz, i8254 clock: 1193072 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz CLK_USE_TSC_CALIBRATION not specified - using old calibration method Timecounter "TSC" frequency 451024656 Hz CPU: Pentium II/Xeon/Celeron (451.02-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x653 Stepping=3 Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,<b24>> real memory = 134217728 (131072K bytes) Physical memory chunk(s): 0x00001000 - 0x0009efff, 647168 bytes (158 pages) 0x00308000 - 0x07ffdfff, 131031040 bytes (31990 pages) avail memory = 127447040 (124460K bytes) Found BIOS32 Service Directory header at 0xf00fdb50 Entry = 0xfdb60 (0xf00fdb60) Rev = 0 Len = 1 PCI BIOS entry at 0xdb81 SMIBIOS header at 0xf00f0080 Version 2.1 Table at 0xf0770, 33 entries, 1010 bytes, largest entry 74 bytes DMI header at 0xf00f0090 Version 2.1 Table at 0xf0770, 33 entries, 1010 bytes Other BIOS signatures found: ACPI: 00000000 $PnP: 000f7420 Preloaded elf kernel "kernel" at 0xf02fb000. pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71a08086) Probing for devices on PCI bus 0: found-> vendor=0x8086, dev=0x71a0, revid=0x00 class=06-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 map[0]: type 3, range 32, base f8000000, size 26 chip0: <Host to PCI bridge (vendor=8086 device=71a0)> rev 0x00 on pci0.0.0 found-> vendor=0x8086, dev=0x71a1, revid=0x00 class=06-04-00, hdrtype=0x01, mfdev=0 subordinatebus=1 secondarybus=1 chip1: <PCI to PCI bridge (vendor=8086 device=71a1)> rev 0x00 on pci0.1.0 found-> vendor=0x8086, dev=0x7110, revid=0x02 class=06-01-00, hdrtype=0x00, mfdev=1 subordinatebus=0 secondarybus=0 chip2: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.7.0 found-> vendor=0x8086, dev=0x7111, revid=0x01 class=01-01-80, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 map[0]: type 4, range 32, base 0000ffa0, size 4 ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1 intel_piix_status: primary master sample = 3, master recovery = 1 intel_piix_status: primary master fastDMAonly disabled, pre/post enabled, intel_piix_status: IORDY sampling enabled, intel_piix_status: fast PIO enabled intel_piix_status: primary slave sample = 5, slave recovery = 4 intel_piix_status: primary slave fastDMAonly disabled, pre/post disabled, intel_piix_status: IORDY sampling disabled, intel_piix_status: fast PIO disabled ide_pci: busmaster 0 status: 24 from port: 0000ffa2 ide_pci: ide0:0 has been configured for DMA by BIOS intel_piix_status: secondary master sample = 5, master recovery = 4 intel_piix_status: secondary master fastDMAonly disabled, pre/post disabled, intel_piix_status: IORDY sampling disabled, intel_piix_status: fast PIO disabled intel_piix_status: secondary slave sample = 5, slave recovery = 4 intel_piix_status: secondary slave fastDMAonly disabled, pre/post disabled, intel_piix_status: IORDY sampling disabled, intel_piix_status: fast PIO disabled ide_pci: busmaster 1 status: 04 from port: 0000ffaa found-> vendor=0x8086, dev=0x7112, revid=0x01 class=0c-03-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=d, irq=255 map[0]: type 4, range 32, base 0000ef80, size 5 found-> vendor=0x8086, dev=0x7113, revid=0x02 class=06-80-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 chip3: <Intel 82371AB Power management controller> rev 0x02 on pci0.7.3 found-> vendor=0x9005, dev=0x005f, revid=0x00 class=01-00-00, hdrtype=0x00, mfdev=1 subordinatebus=0 secondarybus=0 intpin=a, irq=10 map[0]: type 4, range 32, base 0000e400, size 8 map[1]: type 1, range 64, base ffafe000, size 12 map[2]: type 0, range 0, base 00000000, size 0 ahc0: <Adaptec aic7896/97 Ultra2 SCSI adapter> rev 0x00 int a irq 10 on pci0.14.0 ahc0: Reading SEEPROM...done. ahc0: BIOS eeprom not present ahc0: Primary Low Byte termination Enabled ahc0: Primary High Byte termination Enabled ahc0: aic7896/97 Wide Channel A, SCSI Id=7, 16/255 SCBs ahc0: Downloading Sequencer Program... 392 instructions downloaded found-> vendor=0x9005, dev=0x005f, revid=0x00 class=01-00-00, hdrtype=0x00, mfdev=1 subordinatebus=0 secondarybus=0 intpin=a, irq=10 map[0]: type 4, range 32, base 0000e800, size 8 map[1]: type 1, range 64, base ffaff000, size 12 map[2]: type 0, range 0, base 00000000, size 0 ahc1: <Adaptec aic7896/97 Ultra2 SCSI adapter> rev 0x00 int a irq 10 on pci0.14.1 using shared irq10. ahc1: Reading SEEPROM...done. ahc1: BIOS eeprom not present ahc1: Primary Low Byte termination Enabled ahc1: Primary High Byte termination Enabled ahc1: aic7896/97 Wide Channel B, SCSI Id=7, 16/255 SCBs ahc1: Downloading Sequencer Program... 392 instructions downloaded found-> vendor=0x10e8, dev=0x8043, revid=0x01 class=00-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=11 map[0]: type 3, range 32, base feb00000, size 20 mlanai0: <Myrinet PCI interface> rev 0x01 int a irq 11 on pci0.15.0 tpz0: Myrinet LANai 4.1 address 00:60:dd:e0:00:f1 (M2F-PCI32-10241) tpz0: Duke TPZ/IP driver version $Id: if_tpz.c,v 1.12 1999/02/05 20:16:56 gallatin Exp $ found-> vendor=0x8086, dev=0x1229, revid=0x05 class=02-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=10 map[0]: type 3, range 32, base feaff000, size 12 map[1]: type 4, range 32, base 0000ef40, size 5 map[2]: type 1, range 32, base ff900000, size 20 fxp0: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x05 int a irq 10 on pci0.16.0 fxp0: Ethernet address 00:a0:c9:e7:8e:9c bpf: fxp0 attached Probing for devices on PCI bus 1: Initializing PnP override table Probing for PnP devices: Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 No Plug-n-Play devices were found Probing for devices on the ISA bus: sc0: no video adapter is found. sc0 not found atkbdc0 at 0x60-0x6f on motherboard kbdc: DIAGNOSE status:0055 kbdc: TEST_KBD_PORT status:0000 kbdc: DIAGNOSE status:0055 kbdc: TEST_KBD_PORT status:0000 atkbd0 irq 1 on isa kbd0: atkbd0, generic (3), config:0x0, flags:0x1f0000 psm0: current command byte:0065 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fe kbdc: RESET_AUX return code:00fe kbdc: RESET_AUX return code:00fe kbdc: DIAGNOSE status:0055 kbdc: TEST_KBD_PORT status:0000 psm0: failed to reset the aux device. psm0 not found sio0: irq maps: 0x1 0x11 0x1 0x1 sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A, console sio1: irq maps: 0x1 0x9 0x1 0x1 sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A ppc: parallel port found at 0x378 PC873xx probe at 0x2e got unknown ID 0x0 ppc0: SPP ppc0 at 0x378 irq 7 on isa ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode plip: irq 7 plip0: <PLIP network interface> on ppbus 0 bpf: lp0 attached ppi0: <generic parallel i/o> on ppbus 0 psm0: current command byte:0065 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fe kbdc: RESET_AUX return code:00fe kbdc: RESET_AUX return code:00fe kbdc: DIAGNOSE status:0055 kbdc: TEST_KBD_PORT status:0000 psm0: failed to reset the aux device. psm0 not found at 0x60 mss_probe: no address supplied, try default 0x530 mss_detect error, busy still set (0xff) sb_probe: no address supplied, try defaults (0x220,0x240) pcm0 not found fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: FIFO enabled, 8 bytes threshold fd0: 1.44MB 3.5in wdc0 at 0x1f0-0x1f7 irq 14 flags 0xa0ff0ff on isa wdc0: unit 0 (wd0): <QUANTUM FIREBALL EX5.1A>, LBA, DMA, 32-bit, multi-block-16, sleep-hack wd0: 4892MB (10018890 sectors), 623 cyls, 255 heads, 63 S/T, 512 B/S wd0: ATA INQUIRE valid = 0007, dmamword = 0007, apio = 0003, udma = 0407 vga0 not found npx0 flags 0x1 on motherboard npx0: INT 16 interface imasks: bio c0084040, tty c003009a, net c0060c00 BIOS Geometries: 0:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 1:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 2:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 3:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 4:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 5:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 6:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 7:00000000 0..0=1 cylinders, 0..0=1 heads, 1..0=0 sectors 0 accounted for Device configuration finished. RTC BIOS diagnostic error 20<config_unit> bpf: lo0 attached lo0 XXX: driver didn't set ifq_maxlen (noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. (noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. ahc0: Selection Timeout on A:4. 1 SCBs aborted ahc1: Selection Timeout on A:2. 1 SCBs aborted ahc0: Selection Timeout on A:5. 1 SCBs aborted ahc1: Selection Timeout on A:5. 1 SCBs aborted ahc0: Selection Timeout on A:6. 1 SCBs aborted ahc1: Selection Timeout on A:6. 1 SCBs aborted ahc0: Selection Timeout on A:8. 1 SCBs aborted ahc1: Selection Timeout on A:8. 1 SCBs aborted ahc0: Selection Timeout on A:9. 1 SCBs aborted ahc1: Selection Timeout on A:9. 1 SCBs aborted ahc0: Selection Timeout on A:10. 1 SCBs aborted ahc1: Selection Timeout on A:10. 1 SCBs aborted ahc0: Selection Timeout on A:11. 1 SCBs aborted ahc1: Selection Timeout on A:11. 1 SCBs aborted ahc0: Selection Timeout on A:12. 1 SCBs aborted ahc1: Selection Timeout on A:12. 1 SCBs aborted ahc0: Selection Timeout on A:13. 1 SCBs aborted ahc1: Selection Timeout on A:13. 1 SCBs aborted ahc0: Selection Timeout on A:14. 1 SCBs aborted ahc1: Selection Timeout on A:14. 1 SCBs aborted ahc0: Selection Timeout on A:15. 1 SCBs aborted ahc0: target 0 using 16bit transfers ahc1: Selection Timeout on A:15. 1 SCBs aborted ahc0: target 0 synchronous at 20.0MHz, offset = 0xf ahc0: target 3 using 16bit transfers ahc0: target 3 synchronous at 20.0MHz, offset = 0xf ahc0: target 2 using 16bit transfers ahc0: target 2 synchronous at 20.0MHz, offset = 0xf ahc1: target 0 using 16bit transfers ahc1: target 0 synchronous at 20.0MHz, offset = 0xf ahc0: target 1 using 16bit transfers ahc0: target 1 synchronous at 20.0MHz, offset = 0xf ahc1: target 4 using 16bit transfers ahc1: target 4 synchronous at 20.0MHz, offset = 0xf ahc1: target 3 using 16bit transfers ahc1: target 3 synchronous at 20.0MHz, offset = 0xf ahc1: target 1 using 16bit transfers ahc1: target 1 synchronous at 20.0MHz, offset = 0xf pass0 at ahc0 bus 0 target 0 lun 0 pass0: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device pass0: Serial Number LG606047 pass0: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled pass1 at ahc0 bus 0 target 1 lun 0 pass1: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device pass1: Serial Number LG604374 pass1: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled pass2 at ahc0 bus 0 target 2 lun 0 pass2: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device pass2: Serial Number LG117621 pass2: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled pass3 at ahc0 bus 0 target 3 lun 0 pass3: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device pass3: Serial Number LG996535 pass3: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled pass4 at ahc1 bus 0 target 0 lun 0 pass4: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device pass4: Serial Number LG164004 pass4: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled pass5 at ahc1 bus 0 target 1 lun 0 pass5: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device pass5: Serial Number LG604613 pass5: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled pass6 at ahc1 bus 0 target 3 lun 0 pass6: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device pass6: Serial Number LG243960 pass6: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled pass7 at ahc1 bus 0 target 4 lun 0 pass7: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device pass7: Serial Number LG161427 pass7: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled da0 at ahc0 bus 0 target 0 lun 0 da0: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device da0: Serial Number LG606047 da0: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled da0: 4211MB (8625052 512 byte sectors: 255H 63S/T 536C) da3 at ahc0 bus 0 target 3 lun 0 da3: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device da3: Serial Number LG996535 da3: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled da3: 4211MB (8625052 512 byte sectors: 255H 63S/T 536C) da2 at ahc0 bus 0 target 2 lun 0 da2: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device da2: Serial Number LG117621 da2: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled da2: 4211MB (8625052 512 byte sectors: 255H 63S/T 536C) da1 at ahc0 bus 0 target 1 lun 0 da1: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device da1: Serial Number LG604374 da1: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled da1: 4211MB (8625052 512 byte sectors: 255H 63S/T 536C) da4 at ahc1 bus 0 target 0 lun 0 da4: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device da4: Serial Number LG164004 da4: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled da4: 4339MB (8887184 512 byte sectors: 255H 63S/T 553C) da7 at ahc1 bus 0 target 4 lun 0 da7: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device da7: Serial Number LG161427 da7: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled da7: 4339MB (8887184 512 byte sectors: 255H 63S/T 553C) da6 at ahc1 bus 0 target 3 lun 0 da6: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device da6: Serial Number LG243960 da6: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled da6: 4339MB (8887184 512 byte sectors: 255H 63S/T 553C) da5 at ahc1 bus 0 target 1 lun 0 da5: <SEAGATE ST34501W 0018> Fixed Direct Access SCSI-2 device da5: Serial Number LG604613 da5: 40.0MB/s transfers (20.0MHz, offset 15, 16bit), Tagged Queueing Enabled da5: 4339MB (8887184 512 byte sectors: 255H 63S/T 553C) Considering FFS root f/s. changing root device to wd0s1a wd0s1: type 0xa5, start 63, end = 10018889, size 10018827 : OK swapon: adding /dev/wd0s1b as swap device Automatic reboot in progress... /dev/rwd0s1a: FILESYSTEM CLEAN; SKIPPING CHECKS /dev/rwd0s1a: clean, 64268 free (268 frags, 8000 blocks, 0.3% fragmentation) /dev/rwd0s1f: FILESYSTEM CLEAN; SKIPPING CHECKS /dev/rwd0s1f: clean, 2209762 free (11026 frags, 274842 blocks, 0.4% fragmentation) /dev/rwd0s1e: FILESYSTEM CLEAN; SKIPPING CHECKS /dev/rwd0s1e: clean, 1012987 free (211 frags, 126597 blocks, 0.0% fragmentation) ffs_mountfs: superblock updated for soft updates ffs_mountfs: superblock updated for soft updates Doing initial network setup: hostname domain. fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 152.3.145.37 netmask 0xffffff00 broadcast 152.3.145.255 ether 00:a0:c9:e7:8e:9c media: 100baseTX <full-duplex> status: active supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP net.inet.tcp.sendspace: 16384 -> 131072 net.inet.tcp.recvspace: 16384 -> 131072 net.inet.udp.maxdgram: 9216 -> 57344 net.inet.udp.recvspace: 41600 -> 65535 kern.ipc.maxsockbuf: 262144 -> 2097152 ifconfig: interface myri0 does not exist ifconfig: interface myri0 does not exist lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet 127.0.0.1 netmask 0xff000000 add net default: gateway 152.3.145.240 Additional routing options:. routing daemons:. Mounting NFS file systems. recording kernel -c changes additional daemons: syslogdFeb 23 15:56:38 scone /kernel: kbdc: RESET_AUX return code:00fe Feb 23 15:56:38 scone last message repeated 2 times Feb 23 15:56:38 scone /kernel: kbdc: DIAGNOSE status:0055 Feb 23 15:56:38 scone /kernel: kbdc: TEST_KBD_PORT status:0000 Feb 23 15:56:38 scone /kernel: kbdc: TEST_AUX_PORT status:0000 Feb 23 15:56:38 scone /kernel: kbdc: RESET_AUX return code:00fe Feb 23 15:56:38 scone last message repeated 2 times Feb 23 15:56:38 scone /kernel: kbdc: DIAGNOSE status:0055 Feb 23 15:56:38 scone /kernel: kbdc: TEST_KBD_PORT status:0000 . checking for core dump...savecore: no core dump Doing additional network setup: ntpdate xntpd portmap ypbind. Starting final network daemons: nfsiod. setting ELF ldconfig path: /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib setting a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout /usr/local/lib/aout starting standard daemons: inetd cron. Initial rc.i386 initialization: linuxLinux-ELF exec handler installed . rc.i386 configuring syscons:. Local package initialization: Modula-3 printer. starting local daemons:. Tue Feb 23 15:56:43 EST 1999 FreeBSD (scone.cs.duke.edu) (ttyd0) login: da0: invalid primary partition table: no magic ahc0: target 0 using asynchronous transfers ahc0: target 0 synchronous at 20.0MHz, offset = 0xf ahc0: target 0 using asynchronous transfers ahc0: target 0 synchronous at 20.0MHz, offset = 0xf ahc0: target 0 using asynchronous transfers ahc0: target 0 synchronous at 20.0MHz, offset = 0xf ahc0: target 0 using asynchronous transfers ahc0: target 0 synchronous at 20.0MHz, offset = 0xf ahc0: target 0 using asynchronous transfers ahc0: target 0 synchronous at 20.0MHz, offset = 0xf (da0:ahc0:0:0:0): WRITE(06). CDB: a 0 0 0 10 0 (da0:ahc0:0:0:0): ABORTED COMMAND asc:47,0 (da0:ahc0:0:0:0): SCSI parity error field replaceable unit: 3 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-scsi" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?14035.5458.71518.652907>