Date: Wed, 28 Aug 1996 15:43:40 -0700 (PDT) From: Steve Khoo <steve@gordian.com> To: freebsd-current@freebsd.org Cc: freebsd-scsi@freebsd.org, se@ZPR.Uni-Koeln.DE Subject: Re: problems booting with 2 drives on NCR8251D Message-ID: <199608282243.PAA19057@delphi.gordian.com> In-Reply-To: Steve Khoo's message of Mon, 26 Aug 1996 12:15:09 -0700 (PDT) References: <199608261915.MAA10702@delphi.gordian.com>
next in thread | previous in thread | raw e-mail | index | archive | help
FYI: Well, I didn't get any response on this, but finally tracked down the problem to a flaky pin on one of the 68pin FWD SCSI connectors. SEK >>>>> "Steve" == Steve Khoo <steve@gordian.com> writes: Steve> setup: Steve> Asus MB(P55TP4XEG) 512K Cache Steve> 32MB RAM Steve> Fast Wide Differential SCSI Controller (NCR8251D) Steve> Seagate ST12550WD on SCSI ID #0 Steve> Seagate ST15150WD on SCSI ID #1 Steve> The system is running FreeBSD 2.2-CURRENT sup'd on 8/17/96. Steve> The system boots and runs find with just the first(Seagate Steve> ST12550WD) drive. When I added the second(Seagate Steve> ST15150WD) drive I get the following errors. I can boot Steve> dos and do fdisk/format and stuff on the second drive Steve> without any problems. Any ideas what the errors mean? Steve> I'd appreciate any help. Steve> Thanks! Steve> SEK Steve> FreeBSD 2.2-CURRENT #0: Mon Aug 19 12:48:53 PDT 1996 Steve> steve@metis.gordian.com:/usr/src/sys/compile/metis Steve> Calibrating clock(s) relative to mc146818A clock... Steve> i586 clock: 99465569 Hz, i8254 clock: 1193086 Hz Steve> CPU: Pentium (99.47-MHz 586-class CPU) Steve> Origin = "GenuineIntel" Id = 0x525 Stepping=5 Steve> Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8> Steve> real memory = 33554432 (32768K bytes) Steve> avail memory = 30695424 (29976K bytes) Steve> Probing for devices on PCI bus 0: Steve> chip0 <Intel 82437 (Triton) PCI cache memory controller> rev 2 on pci0:0 Steve> chip1 <Intel 82371 (Triton) PCI-ISA bridge> rev 2 on pci0:7:0 Steve> pci0:7:1: Intel Corporation, device=0x1230, class=storage (ide) [no driver assigned] Steve> de0 <Digital DC21140 Fast Ethernet> rev 18 int a irq 12 on pci0:9 Steve> de0: SMC 9332 DC21140 [10-100Mb/s] pass 1.2 Steve> de0: address 00:00:c0:58:c3:e4 Steve> de0: enabling 10baseT port Steve> ncr0 <ncr 53c825 wide scsi> rev 2 int a irq 10 on pci0:10 Steve> ncr0 waiting for scsi devices to settle Steve> (ncr0:0:0): "SEAGATE ST12550W 0004" type 0 fixed SCSI 2 Steve> sd0(ncr0:0:0): Direct-Access Steve> sd0(ncr0:0:0): WIDE SCSI (16 bit) enabled. Steve> sd0(ncr0:0:0): FAST SCSI-2 100ns (10 Mb/sec) offset 8. Steve> 2040MB (4178874 512 byte sectors) Steve> (ncr0:1:0): "SEAGATE ST15150W 0023" type 0 fixed SCSI 2 Steve> sd1(ncr0:1:0): Direct-Access Steve> sd1(ncr0:1:0): WIDE SCSI (16 bit) enabled. Steve> ncr0:1: ERROR (80:91) (9-ae-0) (0/1b) @ (d8c:19000004). Steve> script cmd = 89030000 Steve> reg: da 10 80 1b 47 00 01 07 23 09 81 ae 80 00 0e 08. Steve> ncr0: restart (fatal error). Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400. Steve> ncr0: aborting job ... Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060). Steve> script cmd = 878b0000 Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a. Steve> ncr0: restart (fatal error). Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400. Steve> ncr0: aborting job ... Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060). Steve> script cmd = 878b0000 Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a. Steve> ncr0: restart (fatal error). Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400. Steve> ncr0: aborting job ... Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060). Steve> script cmd = 878b0000 Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a. Steve> ncr0: restart (fatal error). Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400. Steve> ncr0: aborting job ... Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060). Steve> script cmd = 878b0000 Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a. Steve> ncr0: restart (fatal error). Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400. Steve> sd1 could not mode sense (4). Using ficticious geometry Steve> ncr0: aborting job ... Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060). Steve> script cmd = 878b0000 Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a. Steve> ncr0: restart (fatal error). Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400. Steve> ncr0: aborting job ... Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060). Steve> script cmd = 878b0000 Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a. Steve> ncr0: restart (fatal error). Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400. Steve> ncr0: aborting job ... Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060). Steve> script cmd = 878b0000 Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a. Steve> ncr0: restart (fatal error). Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400. Steve> ncr0: aborting job ... Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060). Steve> script cmd = 878b0000 Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a. Steve> ncr0: restart (fatal error). Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400. Steve> ncr0: aborting job ... Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060). Steve> script cmd = 878b0000 Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a. Steve> ncr0: restart (fatal error). Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400. Steve> sd1: could not get size Steve> 0MB (0 512 byte sectors)
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199608282243.PAA19057>