Date: Fri, 27 Dec 2002 21:20:04 -0800 (PST) From: Chuck McCrobie <mccrobie2000@yahoo.com> To: freebsd-scsi@freebsd.org Subject: SCSI Problems with sym and Western Digital on FreeBSD 4.7-stable Message-ID: <20021228052004.77600.qmail@web14812.mail.yahoo.com>
next in thread | raw e-mail | index | archive | help
I am having SCSI problems with the sym driver and a
Western Digital hard disk. Under the -stable kernel
built on 'Dec 1', the drive show up fine with 16-bit
wide transfers at 40 MHz. Under the most recent
-stable kernel built on 'Dec 17', the Western Digital
gets some type of very weird error message. The
Western Digital is "da1".
No changes except cvsup on this machine. Suddenly,
da1 is having problems. I can reboot back to kernel
built on 'Dec 1' and access the disk with _NO_
problems.
Also, I set the controller to do 8-bit transfers to
da1 - no problems there either. So, something
software wise has changed between 'Dec 1' and now.
Do any of you scsi maintainer's have a clue to this
problem? I've looked at the difference in sym_hipd.c
and some others, but nothing really jumps out :(
Attached is the 'dmesg' from the boot-ups of both the
'Dec 1' kernel and the 'Dec 17' kernel.
Sorry for the formatting.
Thanks
mccrobie@cablespeed.com
--
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989,
1991, 1992, 1993, 1994
The Regents of the University of California.
All rights
reserved.
FreeBSD 4.7-STABLE #0: Sun Dec 1 05:05:25 EST 2002
mccrobie@orange.my.domain:/usr/src/sys/compile/smb
Timecounter "i8254" frequency 1193182 Hz
CPU: AMD Athlon(tm) XP 2000+ (1666.73-MHz 686-class
CPU)
Origin = "AuthenticAMD" Id = 0x662 Stepping = 2
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
AMD Features=0xc0400000<AMIE,DSP,3DNow!>
real memory = 536805376 (524224K bytes)
avail memory = 518758400 (506600K bytes)
Preloaded elf kernel "kernel.good.1" at 0xc03e1000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 11 entries at 0xc00f7f40
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=1106 device=b099)>
at device 1.0 on
pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GM graphics accelerator> at 0.0 irq
11
sym0: <875> port 0xe800-0xe8ff mem
0xdfffe000-0xdfffefff,0xdfffff00-0xdfffffff irq 10 at
device 6.0 on pci0
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity
checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: SCAN FOR LUNS disabled for targets 0 1 2 3 4 5
6.
pci0: <unknown card> (vendor=0x104c, dev=0x8019) at
7.0 irq 5
de0: <Digital 21140A Fast Ethernet> port 0xec00-0xec7f
mem
0xdffffe80-0xdffffeff irq 15 at device 8.0 on pci0
de0: 21140A [10-100Mb/s] pass 2.2
de0: address 00:40:05:a2:da:8f
pcib2: <DEC 21152 PCI-PCI bridge> at device 10.0 on
pci0
pci2: <PCI bus> on pcib2
sym1: <875> port 0xc800-0xc8ff mem
0xdfefe000-0xdfefefff,0xdfefff00-0xdfefffff irq 10 at
device 0.0 on pci2
sym1: Symbios NVRAM, ID 7, Fast-20, SE, parity
checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym2: <875> port 0xc400-0xc4ff mem
0xdfefd000-0xdfefdfff,0xdfeffe00-0xdfeffeff irq 5 at
device 1.0 on pci2
sym2: Symbios NVRAM, ID 7, Fast-20, SE, parity
checking
sym2: open drain IRQ line driver, using on-chip SRAM
sym2: using LOAD/STORE-based firmware.
de1: <Digital 21140A Fast Ethernet> port 0xcc00-0xcc7f
mem
0xdfeffd80-0xdfeffdff irq 15 at device 2.0 on pci2
de1: 21140A [10-100Mb/s] pass 2.2
de1: address 00:06:2b:01:24:07
uhci0: <VIA 83C572 USB controller> port 0xdc00-0xdc1f
irq 11 at device
16.0 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xe000-0xe01f
irq 10 at device
16.1 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xe400-0xe41f
irq 5 at device
16.2 on pci0
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <USB controller> at 16.3 irq 15
isab0: <PCI to ISA bridge (vendor=1106 device=3177)>
at device 17.0 on
pci0
isa0: <ISA bus> on isab0
pcm0: <VIA VT8235> port 0xd800-0xd8ff irq 5 at device
17.5 on pci0
orm0: <Option ROMs> at iomem
0xc0000-0xc97ff,0xc9800-0xcbfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7
irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port
0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
0xa0000-0xbffff on
isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio2: configured irq 7 not in bitmap of probed irqs 0
sio3: configured irq 9 not in bitmap of probed irqs 0
pcf0: can't reserve irq, polled mode.
pcf0: <PCF8584 I2C bus controller> at port 0x320-0x321
irq 5 on isa0
iicbus0: <Philips I2C bus> on pcf0 addr 0xaa
iicsmb0: <I2C to SMB bridge> on iicbus0
smbus0: <System Management Bus> on iicsmb0
smb0: <SMBus general purpose I/O> on smbus0
iic0: <I2C general purpose I/O> on iicbus0
IP packet filtering initialized, divert enabled,
rule-based forwarding
enabled, default to deny, logging disabled
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym2:0:-1:-1): SCSI BUS reset delivered.
de0: enabling Full Duplex 100baseTX port
de1: enabling 10baseT port
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
Mounting root from ufs:/dev/da0a
da0 at sym0 bus 0 target 0 lun 0
da0: <SEAGATE ST318406LW 0109> Fixed Direct Access
SCSI-3 device
da0: 40.000MB/s transfers (20.000MHz, offset 16,
16bit), Tagged Queueing
Enabled
da0: 17501MB (35843670 512 byte sectors: 255H 63S/T
2231C)
cd0 at sym1 bus 0 target 2 lun 0
cd0: <MATSHITA PD-2 LF-D100 A114> Removable CD-ROM
SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 16)
cd0: Attempt to query device size failed: NOT READY,
Medium not present
cd1 at sym1 bus 0 target 4 lun 0
cd1: <YAMAHA CRW2100S 1.0K> Removable CD-ROM SCSI-2
device
cd1: 20.000MB/s transfers (20.000MHz, offset 7)
cd1: Attempt to query device size failed: NOT READY,
Medium not present
- tray closed
da1 at sym0 bus 0 target 2 lun 0
da1: <WDIGTL WDE18300 ULTRA2 1.30> Fixed Direct Access
SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 16,
16bit)
da1: 17461MB (35761710 512 byte sectors: 255H 63S/T
2226C)
Waiting (max 60 seconds) for system process `vnlru' to
stop...stopped
Waiting (max 60 seconds) for system process
`bufdaemon' to
stop...stopped
Waiting (max 60 seconds) for system process `syncer'
to stop...stopped
----- Kernel built Dec 17 -----
syncing disks... 11
done
Uptime: 11m52s
Rebooting...
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989,
1991, 1992, 1993, 1994
The Regents of the University of California.
All rights
reserved.
FreeBSD 4.7-STABLE #0: Tue Dec 17 22:50:09 EST 2002
mccrobie@orange.my.domain:/usr/src/sys/compile/orange
Timecounter "i8254" frequency 1193182 Hz
CPU: AMD Athlon(tm) XP 2000+ (1666.74-MHz 686-class
CPU)
Origin = "AuthenticAMD" Id = 0x662 Stepping = 2
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
AMD Features=0xc0400000<AMIE,DSP,3DNow!>
real memory = 536805376 (524224K bytes)
avail memory = 518823936 (506664K bytes)
Preloaded elf kernel "kernel" at 0xc03d2000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 11 entries at 0xc00f7f40
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=1106 device=b099)>
at device 1.0 on
pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GM graphics accelerator> at 0.0 irq
11
sym0: <875> port 0xe800-0xe8ff mem
0xdfffe000-0xdfffefff,0xdfffff00-0xdfffffff irq 10 at
device 6.0 on pci0
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity
checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: SCAN FOR LUNS disabled for targets 0 1 2 3 4 5
6.
pci0: <unknown card> (vendor=0x104c, dev=0x8019) at
7.0 irq 5
de0: <Digital 21140A Fast Ethernet> port 0xec00-0xec7f
mem
0xdffffe80-0xdffffeff irq 15 at device 8.0 on pci0
de0: 21140A [10-100Mb/s] pass 2.2
de0: address 00:40:05:a2:da:8f
pcib2: <DEC 21152 PCI-PCI bridge> at device 10.0 on
pci0
pci2: <PCI bus> on pcib2
sym1: <875> port 0xc800-0xc8ff mem
0xdfefe000-0xdfefefff,0xdfefff00-0xdfefffff irq 10 at
device 0.0 on pci2
sym1: Symbios NVRAM, ID 7, Fast-20, SE, parity
checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym2: <875> port 0xc400-0xc4ff mem
0xdfefd000-0xdfefdfff,0xdfeffe00-0xdfeffeff irq 5 at
device 1.0 on pci2
sym2: Symbios NVRAM, ID 7, Fast-20, SE, parity
checking
sym2: open drain IRQ line driver, using on-chip SRAM
sym2: using LOAD/STORE-based firmware.
de1: <Digital 21140A Fast Ethernet> port 0xcc00-0xcc7f
mem
0xdfeffd80-0xdfeffdff irq 15 at device 2.0 on pci2
de1: 21140A [10-100Mb/s] pass 2.2
de1: address 00:06:2b:01:24:07
uhci0: <VIA 83C572 USB controller> port 0xdc00-0xdc1f
irq 11 at device
16.0 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xe000-0xe01f
irq 10 at device
16.1 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xe400-0xe41f
irq 5 at device
16.2 on pci0
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <USB controller> at 16.3 irq 15
isab0: <PCI to ISA bridge (vendor=1106 device=3177)>
at device 17.0 on
pci0
isa0: <ISA bus> on isab0
pcm0: <VIA VT8235> port 0xd800-0xd8ff irq 5 at device
17.5 on pci0
orm0: <Option ROMs> at iomem
0xc0000-0xc97ff,0xc9800-0xcbfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7
irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port
0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
0xa0000-0xbffff on
isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio2: configured irq 7 not in bitmap of probed irqs 0
sio3: configured irq 9 not in bitmap of probed irqs 0
IP packet filtering initialized, divert enabled,
rule-based forwarding
enabled, default to deny, logging disabled
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym2:0:-1:-1): SCSI BUS reset delivered.
de0: enabling Full Duplex 100baseTX port
de1: enabling 10baseT port
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
(probe2:sym0:0:2:0): ODD transfer in DATA IN phase.
(probe2:sym0:0:2:0): COMMAND FAILED (87 0 10).
(probe2:sym0:0:2:0): ODD transfer in DATA IN phase.
(probe2:sym0:0:2:0): COMMAND FAILED (87 0 10).
(probe2:sym0:0:2:0): ODD transfer in DATA IN phase.
(probe2:sym0:0:2:0): COMMAND FAILED (87 0 10).
(probe2:sym0:0:2:0): ODD transfer in DATA IN phase.
(probe2:sym0:0:2:0): COMMAND FAILED (87 0 10).
(probe2:sym0:0:2:0): ODD transfer in DATA IN phase.
(probe2:sym0:0:2:0): COMMAND FAILED (87 0 10).
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
sym2: unexpected disconnect
Mounting root from ufs:/dev/da0a
da0 at sym0 bus 0 target 0 lun 0
da0: <SEAGATE ST318406LW 0109> Fixed Direct Access
SCSI-3 device
da0: 40.000MB/s transfers (20.000MHz, offset 16,
16bit), Tagged Queueing
Enabled
da0: 17501MB (35843670 512 byte sectors: 255H 63S/T
2231C)
cd0 at sym1 bus 0 target 2 lun 0
cd0: <MATSHITA PD-2 LF-D100 A114> Removable CD-ROM
SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 16)
cd0: Attempt to query device size failed: NOT READY,
Medium not present
cd1 at sym1 bus 0 target 4 lun 0
cd1: <YAMAHA CRW2100S 1.0K> Removable CD-ROM SCSI-2
device
cd1: 20.000MB/s transfers (20.000MHz, offset 7)
cd1: Attempt to query device size failed: NOT READY,
Medium not present
- tray closed
__________________________________________________
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now.
http://mailplus.yahoo.com
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-scsi" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20021228052004.77600.qmail>