Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 25 Dec 2014 23:03:08 +0200
From:      George Kontostanos <gkontos.mail@gmail.com>
To:        Steven Hartland <killing@multiplay.co.uk>
Cc:        "freebsd-fs@freebsd.org" <freebsd-fs@freebsd.org>
Subject:   Re: LSI SAS 9300-8i weird ZFS checksum errors
Message-ID:  <CA%2BdUSyrkfp%2Bgz1zqCJJWo=VjMuEJf6A4vEmOpqzu7L-sAU9U%2Bg@mail.gmail.com>
In-Reply-To: <549C65FF.4010702@multiplay.co.uk>
References:  <CA%2BdUSyo56ioZC4Kn4XTcf_GgeSsQrtd7FYpCxjsqOxQ5ON-_CA@mail.gmail.com> <549C65FF.4010702@multiplay.co.uk>

next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, Dec 25, 2014 at 9:31 PM, Steven Hartland <killing@multiplay.co.uk>
wrote:

>
> On 25/12/2014 14:39, George Kontostanos wrote:
>
>> Hello, list and Merry Christmas to all
>>
>> I am facing some weird checksum errors during scrub. The configuration is
>> the following:
>>
>> Board:        Supermicro Motherboard X10DRi-T4+ (
>> http://www.supermicro.com/products/motherboard/xeon/c600/x10dri-t4_.cfm)
>> Controller:  LSI SAS 9300-8i (
>> http://www.lsi.com/products/host-bus-adapters/pages/lsi-sas-9300-8i.aspx)
>> HDD:         21X6TB Western Digital WD60EFRX
>> HDD:         2XIntel SATA 600GB Solid-State Drive SSDSC2BB600G401 DC S3500
>> (SWAP, ZIL, CACHE)
>> Chassis:    Supermicro 847BE1C-R1K28LPB 4U Storage Chassis
>> RAM:         64 GB
>>
>> I installed initially FreeBSD 10.1-RELEASE created one pool consistent by
>> 3
>> X7disk VDEVs in RAIDZ3. I used NFS to start copying some data. After
>> copying around 3TB I initiated a scrub.
>> The result was the following: http://pastebin.com/rswgCY2A and
>> http://pastebin.com/DQ2urGXk
>>
>> I tried to flash the controller but the LSI utility did not recognize the
>> controller. I installed FreeBSD 9.3-RELEASE and used LSI's mpslsi3 driver.
>> I was able to flash the latest bios and firmware that way.
>>
>> LSI Corporation SAS3 Flash Utility
>> Version 07.00.00.00 (2014.08.14)
>> Copyright (c) 2008-2014 LSI Corporation. All rights reserved
>>
>> Adapter Selected is a LSI SAS: SAS3008(C0)
>>
>> Controller Number              : 0
>> Controller                     : SAS3008(C0)
>> PCI Address                    : 00:82:00:00
>> SAS Address                    : 500605b-0-06ce-27e0
>> NVDATA Version (Default)       : 06.03.00.05
>> NVDATA Version (Persistent)    : 06.03.00.05
>> Firmware Product ID            : 0x2221 (IT)
>> Firmware Version               : 06.00.00.00
>> NVDATA Vendor                  : LSI
>> NVDATA Product ID              : SAS9300-8i
>> BIOS Version                   : 08.13.00.00
>> UEFI BSD Version               : 02.00.00.00
>> FCODE Version                  : N/A
>> Board Name                     : SAS9300-8i
>> Board Assembly                 : H3-25573-00E
>> Board Tracer Number            : SV32928040
>>
>> I recreated the pool again and started writing data via NFS again. After 3
>> TB of data I started a scrub and I am still getting checksum errors though
>> there are no messages regarding the drives anymore in /var/log/messages
>>
>>    pool: Pool
>>   state: ONLINE
>> status: One or more devices has experienced an unrecoverable error.  An
>> attempt was made to correct the error.  Applications are unaffected.
>> action: Determine if the device needs to be replaced, and clear the errors
>> using 'zpool clear' or replace the device with 'zpool replace'.
>>     see: http://illumos.org/msg/ZFS-8000-9P
>>
>>    scan: scrub in progress since Thu Dec 25 08:46:21 2014
>>          2.28T scanned out of 5.54T at 816M/s, 1h9m to go
>>          11.9M repaired, 41.26% done
>> config:
>>
>> NAME                     STATE     READ WRITE CKSUM
>> Pool                     ONLINE       0     0     0
>>    raidz3-0               ONLINE       0     0     0
>>      gpt/WD-WX41D94RN5A3  ONLINE       0     0    15  (repairing)
>>      gpt/WD-WX41D948YE1U  ONLINE       0     0    14  (repairing)
>>      gpt/WD-WX41D94RN879  ONLINE       0     0    16  (repairing)
>>      gpt/WD-WX21D947NC83  ONLINE       0     0    24  (repairing)
>>      gpt/WD-WX21D947NT77  ONLINE       0     0    15  (repairing)
>>      gpt/WD-WX41D948YAKV  ONLINE       0     0    19  (repairing)
>>      gpt/WD-WX21D9421SCV  ONLINE       0     0    20  (repairing)
>>    raidz3-1               ONLINE       0     0     0
>>      gpt/WD-WX21D9421F6F  ONLINE       0     0    16  (repairing)
>>      gpt/WD-WX41D948YPN4  ONLINE       0     0    14  (repairing)
>>      gpt/WD-WX21D947NE2K  ONLINE       0     0    22  (repairing)
>>      gpt/WD-WX41D948Y2PX  ONLINE       0     0    19  (repairing)
>>      gpt/WD-WX41D94RNAX7  ONLINE       0     0    17  (repairing)
>>      gpt/WD-WX21D947N1RP  ONLINE       0     0    12  (repairing)
>>      gpt/WD-WX21D94216X7  ONLINE       0     0    20  (repairing)
>>    raidz3-2               ONLINE       0     0     0
>>      gpt/WD-WX41D948YAHP  ONLINE       0     0    25  (repairing)
>>      gpt/WD-WX21D947N06F  ONLINE       0     0    18  (repairing)
>>      gpt/WD-WX21D947N3T1  ONLINE       0     0    21  (repairing)
>>      gpt/WD-WX41D94RNT7D  ONLINE       0     0     5  (repairing)
>>      gpt/WD-WX41D948Y9VV  ONLINE       0     0    18  (repairing)
>>      gpt/WD-WX41D94RNS62  ONLINE       0     0    24  (repairing)
>>      gpt/WD-WX21D9421ZP9  ONLINE       0     0    28  (repairing)
>> logs
>>    mirror-3               ONLINE       0     0     0
>>      gpt/zil0             ONLINE       0     0     0
>>      gpt/zil1             ONLINE       0     0     0
>> cache
>>    gpt/cache0             ONLINE       0     0     0
>>    gpt/cache1             ONLINE       0     0     0
>>
>> errors: No known data errors
>>
>> This is really driving me crazy since smartmon tools do not display any
>> errors on the drives.
>>
>> Any suggestions are most welcomed!!!
>>
>>  Check for bad hardware, first guess would be memory, next would be
> hotswap backplane.
>
>     Regards
>     Steve
> _______________________________________________
> freebsd-fs@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-fs
> To unsubscribe, send any mail to "freebsd-fs-unsubscribe@freebsd.org"
>

Hi Steve,

Memory looks good in memtest. I am not sure what you mean regarding hotswap
backplane.

-- 
George Kontostanos
---



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CA%2BdUSyrkfp%2Bgz1zqCJJWo=VjMuEJf6A4vEmOpqzu7L-sAU9U%2Bg>