Skip site navigation (1)Skip section navigation (2)
Date:      Sat, 14 May 2011 18:48:16 +0400
From:      Andrey Chernov <ache@freebsd.org>
To:        freebsd-net@freebsd.org
Cc:        current@freebsd.org
Subject:   msk0: watchdog timeout (Yukon EC Ultra)
Message-ID:  <20110514144815.GA98013@vniz.net>

next in thread | raw e-mail | index | archive | help
Hi.
With recent -current I start to get 
May 14 13:32:48 xxx kernel: msk0: watchdog timeout
May 14 13:32:48 xxx kernel: msk0: link state changed to DOWN
May 14 13:32:51 xxx kernel: msk0: link state changed to UP
with ~10 minutes interval usually at the starting of receiving essential 
traffic. I run my on-board Gigabit Ethernet in the 100baseTX mode.
Below is detaled info.
Can anybody help?

mskc0: <Marvell Yukon 88E8056 Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfeafc000-0xfeafffff irq 17 at device 0.0 on pci2
mskc0: MSI count : 1
mskc0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 258 to local APIC 0 vector 54
mskc0: using IRQ 258 for MSI
mskc0: RAM buffer size : 0KB
msk0: <Marvell Technology Group Ltd. Yukon EC Ultra Id 0xb4 Rev 0x03> on mskc0
miibus0: <MII bus> on msk0
e1000phy0: <Marvell 88E1149 Gigabit PHY> PHY 0 on miibus0
e1000phy0: OUI 0x000ac2, model 0x000b, rev. 1
e1000phy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow

mskc0@pci0:2:0:0:	class=0x020000 card=0x81f81043 chip=0x436411ab rev=0x12 hdr=0x00
    vendor     = 'Marvell Semiconductor (Was: Galileo Technology Ltd)'
    device     = 'Yukon PCI-E Gigabit Ethernet Controller (88E8056)'
    class      = network
    subclass   = ethernet
    cap 01[48] = powerspec 3  supports D0 D1 D2 D3  current D0
    cap 03[50] = VPD
    cap 05[5c] = MSI supports 1 message, 64 bit enabled with 1 message
    cap 10[e0] = PCI-Express 1 legacy endpoint max data 128(128) link x1(x1)
ecap 0001[100] = AER 1 0 fatal 0 non-fatal 1 corrected

msk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1492
	options=c011b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4,VLAN_HWTSO,LINKSTATE>
	nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
	media: Ethernet 100baseTX <full-duplex> (100baseTX <full-duplex,flowcontrol,rxpause,txpause>)
	status: active

-- 
http://ache.vniz.net/



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20110514144815.GA98013>