Date: Fri, 25 Oct 2002 17:54:18 +0100 (BST) From: Mark Valentine <mark@thuvia.demon.co.uk> To: freebsd-smp@freebsd.org Subject: ahc-related panic on boot, dual PPro system Message-ID: <200210251654.g9PGsIK5074910@dotar.thuvia.org>
next in thread | raw e-mail | index | archive | help
I have a dual Pentium Pro system which is extremely temperamental running
a -CURRENT SMP kernel, as in it'll only boot for me once every few attempts.
I noticed problems about a year ago, when I would generally just get
an ahc timeout and reset and it would eventually come up, but I didn't
pursue it at the time as it's mostly been running -STABLE since then.
It's also been running OpenUNIX 8 in SMP and a couple of flavours of Linux
MP kernel, without complaint, though it's mostly been idle.
However, now it's running -CURRENT again and is up to date, but is even
more flaky. On the other hand, once it does come up, it will generally
survive a make world (/usr/src and /usr/obj are NFS mounted).
Is there anything about this system which should cause such unreliable
booting of -CURRENT SMP (it doesn't have problems booting GENERIC)?
First off, here's a typical boot panic:
-------------------------------------------------------------------------------
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #2: Fri Oct 25 12:32:29 BST 2002
root@carthoris.thuvia.org:/usr/obj/usr/src/sys/SMP
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0673000.
Preloaded elf module "/boot/kernel/aout.ko" at 0xc06730b4.
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium Pro (195.84-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x619 Stepping = 9
Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV>
real memory = 134217728 (131072K bytes)
avail memory = 123179008 (120292K bytes)
APIC_IO: MP table broken: 8259->APIC entry missing!
Programming 16 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 14, version: 0x000f0011, at 0xfec00000
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82454KX/GX (Orion) host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
pci0: <display, VGA> at device 5.0 (no driver attached)
lnc0: <PCNet/PCI Ethernet adapter> port 0xff80-0xff9f mem 0xffbe4fe0-0xffbe4fff irq 9 at device 6.0 on pci0
lnc0: Attaching PCNet/PCI Ethernet adapter
lnc0: PCnet-PCI address 08:00:36:6c:1e:03
ahc0: <Adaptec aic7850 SCSI adapter> port 0xf400-0xf4ff mem 0xffbe5000-0xffbe5fff irq 15 at device 7.0 on pci0
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
ahc1: <Adaptec 2940 Ultra SCSI adapter> port 0xf800-0xf8ff mem 0xffbe6000-0xffbe6fff irq 11 at device 13.0 on pci0
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xff00-0xff3f mem 0xff900000-0xff9fffff,0xffbe7000-0xffbe7fff irq 9 at device 15.0 on pci0
fxp0: Ethernet address 00:90:27:af:3b:a1
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <memory, RAM> at device 20.0 (no driver attached)
orm0: <Option ROMs> at iomem 0xcf800-0xcffff,0xce800-0xcf7ff,0xc0000-0xc7fff on isa0
ata0 at port 0x3f6,0x1f0-0x1f7 irq 14 on isa0
ata1 at port 0x376,0x170-0x177 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
pmtimer0 on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0400> can't assign resources (port)
unknown: <PNP0500> can't assign resources (port)
unknown: <PNP0500> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
Timecounters tick every 10.000 msec
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
Waiting 15 seconds for SCSI devices to settle
ahc_intr: HOST_MSG_LOOP bad phase 0x0
ahc1: Spurious SCSI interrupt
(probe11:ahc1:0:4:0): SCB 0x6 - timed out
ahc1: Dumping Card State while idle, at SEQADDR 0x17
ACCUM = 0x11, SINDEX = 0x20, DINDEX = 0xc0, ARG_2 = 0x4
HCNT = 0x0 SCBPTR = 0x1
SCSISEQ = 0x12, SBLKCTL = 0x2
DFCNTRL = 0x4, DFSTATUS = 0x6d
LASTPHASE = 0x1, SCSISIGI = 0x0, SXFRCTL0 = 0x80
SSTAT0 = 0x5, SSTAT1 = 0x0
STACK == 0xe3, 0x0, 0x190, 0xe
SCB count = 20
Kernel NEXTQSCB = 14
Card NEXTQSCB = 32
QINFIFO entries:
Waiting Queue entries: 1:0
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info: 0(c 0x58, s 0x47, l 0, t 0x6) 1(c 0x8, s 0x7, l 17, t 0x0) 2(c 0x0, s 0xff, l 255, t 0xff) 3(c 0x0, s 0xff, l 255, t 0xff) 4(c 0x0, s 0xff, l 255, t 0xff) 5(c 0x0, s 0xff, l 255, t 0xff) 6(c 0x0, s 0xff, l 255, t 0xff) 7(c 0x0, s 0xff, l 255, t 0xff) 8(c 0x0, s 0xff, l 255, t 0xff) 9(c 0x0, s 0xff, l 255, t 0xff) 10(c 0x0, s 0xff, l 255, t 0xff) 11(c 0x0, s 0xff, l 255, t 0xff) 12(c 0x0, s 0xff, l 255, t 0xff) 13(c 0x0, s 0xff, l 255, t 0xff) 14(c 0x0, s 0xff, l 255, t 0xff) 15(c 0x0, s 0xff, l 255, t 0xff)
Pending list: 17(c 0x8, s 0x7, l 0), 6(c 0x58, s 0x47, l 0)
Kernel Free SCB list: 15 16 9 18 19 0 1 2 3 4 5 7 8 13 12 11 10
Untagged Q(0): 17
Untagged Q(4): 6
scb_index = 0, next = 1
panic: Waiting List traversal
cpuid = 0; lapic.id = 01000000
Debugger("panic")
Stopped at Debugger+0x55: xchgl %ebx,in_Debugger.0
db> trace
Debugger(c04c39b2,1000000,c048e160,c86ecc14,1) at Debugger+0x55
panic(c048e160,0,1,0,c86ecc54) at panic+0x11f
ahc_search_qinfifo(c0bd8400,4,41,0,6) at ahc_search_qinfifo+0x499
ahc_timeout(c1914118,0,c04c46a3,bf,1eb4) at ahc_timeout+0x424
softclock(0,0,c04c13ec,230,c0bde700) at softclock+0x19c
ithread_loop(c0bce600,c86ecd48,c04c1146,354,0) at ithread_loop+0x182
fork_exit(c02cd6c0,c0bce600,c86ecd48) at fork_exit+0xa5
fork_trampoline() at fork_trampoline+0x1a
--- trap 0x1, eip = 0, esp = 0xc86ecd7c, ebp = 0 ---
-------------------------------------------------------------------------------
Next is a boot which just manages to succeed:
-------------------------------------------------------------------------------
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #2: Fri Oct 25 12:32:29 BST 2002
root@carthoris.thuvia.org:/usr/obj/usr/src/sys/SMP
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0673000.
Preloaded elf module "/boot/kernel/aout.ko" at 0xc06730b4.
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium Pro (199.83-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x619 Stepping = 9
Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV>
real memory = 134217728 (131072K bytes)
avail memory = 123179008 (120292K bytes)
APIC_IO: MP table broken: 8259->APIC entry missing!
Programming 16 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 14, version: 0x000f0011, at 0xfec00000
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82454KX/GX (Orion) host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
pci0: <display, VGA> at device 5.0 (no driver attached)
lnc0: <PCNet/PCI Ethernet adapter> port 0xff80-0xff9f mem 0xffbe4fe0-0xffbe4fff irq 9 at device 6.0 on pci0
lnc0: Attaching PCNet/PCI Ethernet adapter
lnc0: PCnet-PCI address 08:00:36:6c:1e:03
ahc0: <Adaptec aic7850 SCSI adapter> port 0xf400-0xf4ff mem 0xffbe5000-0xffbe5fff irq 15 at device 7.0 on pci0
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
ahc1: <Adaptec 2940 Ultra SCSI adapter> port 0xf800-0xf8ff mem 0xffbe6000-0xffbe6fff irq 11 at device 13.0 on pci0
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xff00-0xff3f mem 0xff900000-0xff9fffff,0xffbe7000-0xffbe7fff irq 9 at device 15.0 on pci0
fxp0: Ethernet address 00:90:27:af:3b:a1
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <memory, RAM> at device 20.0 (no driver attached)
orm0: <Option ROMs> at iomem 0xcf800-0xcffff,0xce800-0xcf7ff,0xc0000-0xc7fff on isa0
ata0 at port 0x3f6,0x1f0-0x1f7 irq 14 on isa0
ata1 at port 0x376,0x170-0x177 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
pmtimer0 on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0400> can't assign resources (port)
unknown: <PNP0500> can't assign resources (port)
unknown: <PNP0500> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
Timecounters tick every 10.000 msec
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
Waiting 15 seconds for SCSI devices to settle
ahc_intr: HOST_MSG_LOOP bad phase 0x0
ahc1: Spurious SCSI interrupt
(probe11:ahc1:0:4:0): SCB 0x3 - timed out
ahc1: Dumping Card State while idle, at SEQADDR 0x7
ACCUM = 0x18, SINDEX = 0xe, DINDEX = 0x8c, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x1
SCSISEQ = 0x12, SBLKCTL = 0x2
DFCNTRL = 0x0, DFSTATUS = 0x29
LASTPHASE = 0x1, SCSISIGI = 0x0, SXFRCTL0 = 0x80
SSTAT0 = 0x0, SSTAT1 = 0xa
STACK == 0xe3, 0x160, 0x105, 0x3
SCB count = 20
Kernel NEXTQSCB = 7
Card NEXTQSCB = 7
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info: 0(c 0x58, s 0x47, l 0, t 0x3) 1(c 0x8, s 0x7, l 0, t 0xff) 2(c 0x0, s 0xff, l 255, t 0xff) 3(c 0x0, s 0xff, l 255, t 0xff) 4(c 0x0, s 0xff, l 255, t 0xff) 5(c 0x0, s 0xff, l 255, t 0xff) 6(c 0x0, s 0xff, l 255, t 0xff) 7(c 0x0, s 0xff, l 255, t 0xff) 8(c 0x0, s 0xff, l 255, t 0xff) 9(c 0x0, s 0xff, l 255, t 0xff) 10(c 0x0, s 0xff, l 255, t 0xff) 11(c 0x0, s 0xff, l 255, t 0xff) 12(c 0x0, s 0xff, l 255, t 0xff) 13(c 0x0, s 0xff, l 255, t 0xff) 14(c 0x0, s 0xff, l 255, t 0xff) 15(c 0x0, s 0xff, l 255, t 0xff)
Pending list: 3(c 0x58, s 0x47, l 0)
Kernel Free SCB list: 14 15 16 17 18 19 0 1 2 4 5 6 8 9 13 12 11 10
Untagged Q(4): 3
(probe11:ahc1:0:4:0): Queuing a BDR SCB
(probe11:ahc1:0:4:0): Bus Device Reset Message Sent
(probe11:ahc1:0:4:0): (probe11:ahc1:0:4:0): no longer in timeout, status = 353
Unexpected busfree in Message-out phase
SEQADDR == 0x1b6
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/da0s3a
da0 at ahc1 bus 0 target 0 lun 0
da0: <IBM DDRS-34560W S98G> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 4303MB (8813870 512 byte sectors: 255H 63S/T 548C)
cd0 at ahc1 bus 0 target 4 lun 0
cd0: <MATSHITA CD-ROM CR-506 IG04> Removable CD-ROM SCSI-2 device
cd0: 5.000MB/s transfers (5.000MHz, offset 15)
cd0: Attempt to query device size failed: NOT READY, Medium not present
0000 00 01 41 9d 82 fe 7f ab 3f 00 00 00 10 ad 03 00 |..A.....?.......|
[0] f:00 typ:130 s(CHS):157/1/65 e(CHS):171/254/127 s:63 l:240912
0000 00 00 41 ac 05 fe 7f b7 4f ad 03 00 0c f1 02 00 |..A.....O.......|
[1] f:00 typ:5 s(CHS):172/0/65 e(CHS):183/254/127 s:240975 l:192780
0000 80 01 41 ac 83 fe 7f b7 3f 00 00 00 cd f0 02 00 |..A.....?.......|
[0] f:80 typ:131 s(CHS):172/1/65 e(CHS):183/254/127 s:63 l:192717
0000 00 00 41 b8 05 fe 7f c1 5b 9e 06 00 8a 73 02 00 |..A.....[....s..|
[1] f:00 typ:5 s(CHS):184/0/65 e(CHS):193/254/127 s:433755 l:160650
0000 00 01 41 b8 83 fe 7f c1 3f 00 00 00 4b 73 02 00 |..A.....?...Ks..|
[0] f:00 typ:131 s(CHS):184/1/65 e(CHS):193/254/127 s:63 l:160587
0000 00 00 41 c2 05 fe bf 0a e5 11 09 00 09 e5 11 00 |..A.............|
[1] f:00 typ:5 s(CHS):194/0/65 e(CHS):10/254/191 s:594405 l:1172745
0000 00 01 41 c2 83 fe bf 0a 3f 00 00 00 ca e4 11 00 |..A.....?.......|
[0] f:00 typ:131 s(CHS):194/1/65 e(CHS):10/254/191 s:63 l:1172682
0000 00 00 81 0b 05 fe bf 23 ee f6 1a 00 d9 20 06 00 |.......#..... ..|
[1] f:00 typ:5 s(CHS):11/0/129 e(CHS):35/254/191 s:1767150 l:401625
0000 00 01 81 0b 83 fe bf 23 3f 00 00 00 9a 20 06 00 |.......#?.... ..|
[0] f:00 typ:131 s(CHS):11/1/129 e(CHS):35/254/191 s:63 l:401562
0000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
-------------------------------------------------------------------------------
And here's an attempt at a verbose boot, which got past the usual panic point
but eventually seemed to hang:
-------------------------------------------------------------------------------
SMAP type=01 base=00000000 00000000 len=00000000 0009fc00
SMAP type=02 base=00000000 0009fc00 len=00000000 00000400
SMAP type=01 base=00000000 00100000 len=00000000 07f00000
SMAP type=02 base=00000000 fec00000 len=00000000 00001000
SMAP type=02 base=00000000 fee00000 len=00000000 00001000
SMAP type=02 base=00000000 fffe0000 len=00000000 00020000
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #2: Fri Oct 25 12:32:29 BST 2002
root@carthoris.thuvia.org:/usr/obj/usr/src/sys/SMP
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0673000.
Preloaded elf module "/boot/kernel/aout.ko" at 0xc06730b8.
Calibrating clock(s) ... TSC clock: 199999231 Hz, i8254 clock: 1194176 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium Pro (193.84-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x619 Stepping = 9
Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV>
real memory = 134217728 (131072K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x0069d000 - 0x07ff7fff, 127250432 bytes (31067 pages)
avail memory = 123179008 (120292K bytes)
APIC_IO: MP table broken: 8259->APIC entry missing!
Programming 16 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 14, version: 0x000f0011, at 0xfec00000
bios32: Found BIOS32 Service Directory header at 0xc00f6710
bios32: Entry = 0xf6720 (c00f6720) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x6741
pnpbios: Found PnP BIOS data at 0xc00f9000
pnpbios: Entry = f0000:8520 Rev = 1.0
Other BIOS signatures found:
Initializing GEOMetry subsystem
g_add_class(DEV)
g_add_class(DISK)
g_add_class(BSD)
g_add_class(MBR)
g_add_class(MBREXT)
g_add_class(GEOMCTL)
g_call_me(0xc02aacf0, 0
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
SMP: CPU0 bsp_apic_configure():
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000010 SVR: 0x000001ff
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x80001044
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 1 2 [class=000000] 3 4 5 [class=030000] [hdr=00] is there (id=0519102b)
pcib0: <Intel 82454KX/GX (Orion) host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x0484, revid=0x88
bus=0, slot=2, func=0
class=00-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x000f, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base ffbec000, size 14, enabled
map[14]: type 3, range 32, base ff000000, size 23, enabled
found-> vendor=0x102b, dev=0x0519, revid=0x01
bus=0, slot=5, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0083, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[10]: type 4, range 32, base 0000ff80, size 5, enabled
map[14]: type 1, range 32, base ffbe4fe0, size 5, enabled
found-> vendor=0x1022, dev=0x2000, revid=0x16
bus=0, slot=6, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
map[10]: type 4, range 32, base 0000f400, size 8, enabled
map[14]: type 1, range 32, base ffbe5000, size 12, enabled
found-> vendor=0x9004, dev=0x5078, revid=0x00
bus=0, slot=7, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x04 (1000 ns)
intpin=a, irq=15
map[10]: type 4, range 32, base 0000f800, size 8, enabled
map[14]: type 1, range 32, base ffbe6000, size 12, enabled
found-> vendor=0x9004, dev=0x8178, revid=0x00
bus=0, slot=13, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=11
map[10]: type 1, range 32, base ffbe7000, size 12, enabled
map[14]: type 4, range 32, base 0000ff00, size 6, enabled
map[18]: type 1, range 32, base ff900000, size 20, enabled
found-> vendor=0x8086, dev=0x1229, revid=0x08
bus=0, slot=15, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=0x8086, dev=0x84c5, revid=0x04
bus=0, slot=20, func=0
class=05-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x84c4, revid=0x04
bus=0, slot=25, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x2200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
PCI-ISA bridge with incorrect subclass 0x0
PCI-ISA bridge with incorrect subclass 0x0
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
pci0: <display, VGA> at device 5.0 (no driver attached)
lnc0: <PCNet/PCI Ethernet adapter> port 0xff80-0xff9f mem 0xffbe4fe0-0xffbe4fff irq 9 at device 6.0 on pci0
lnc0: Attaching PCNet/PCI Ethernet adapter
bpf: lnc0 attached
lnc0: PCnet-PCI address 08:00:36:6c:1e:03
ahc0: <Adaptec aic7850 SCSI adapter> port 0xf400-0xf4ff mem 0xffbe5000-0xffbe5fff irq 15 at device 7.0 on pci0
ahc0: No SEEPROM available.
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
ahc0: Downloading Sequencer Program... 429 instructions downloaded
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
ahc1: <Adaptec 2940 Ultra SCSI adapter> port 0xf800-0xf8ff mem 0xffbe6000-0xffbe6fff irq 11 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: internal 50 cable is present, internal 68 cable is present
ahc1: external cable not present
ahc1: BIOS eeprom is present
ahc1: High byte termination Enabled
ahc1: Downloading Sequencer Program... 439 instructions downloaded
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xff00-0xff3f mem 0xff900000-0xff9fffff,0xffbe7000-0xffbe7fff irq 9 at device 15.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 00:90:27:af:3b:a1
fxp0: PCI IDs: 8086 1229 8086 000c 0008
fxp0: Dynamic Standby mode is disabled
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
pci0: <memory, RAM> at device 20.0 (no driver attached)
lnc: lnc0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ex_isa_identify()
pnpbios: 18 devices, largest 66 bytes
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0xe0000-0xfffff, size=0x20000
PNP0c01: adding fixed memory32 range 0x100000-0x80fffff, size=0x8000000
pnpbios: handle 0 device ID PNP0c01 (010cd041)
PNP0f13: adding irq mask 0x1000
pnpbios: handle 1 device ID PNP0f13 (130fd041)
PNP0200: adding dma mask 0x10
PNP0200: adding fixed io range 0-0xf, size=0x10, align=0x1
PNP0200: adding fixed io range 0x80-0x90, size=0x11, align=0x1
PNP0200: adding fixed io range 0x94-0x9f, size=0xc, align=0x1
PNP0200: adding fixed io range 0xc0-0xde, size=0x1f, align=0x1
pnpbios: handle 3 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding fixed io range 0x40-0x43, size=0x4, align=0x1
pnpbios: handle 4 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding fixed io range 0x70-0x71, size=0x2, align=0x1
pnpbios: handle 5 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding fixed io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding fixed io range 0x64-0x64, size=0x1, align=0x1
pnpbios: handle 6 device ID PNP0303 (0303d041)
PNP0800: adding fixed io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 7 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding fixed io range 0xf0-0xff, size=0x10, align=0x1
pnpbios: handle 8 device ID PNP0c04 (040cd041)
pnpbios: handle 9 device ID PNP0a03 (030ad041)
PNP0e00: adding fixed io range 0x3e0-0x3e1, size=0x2, align=0x1
pnpbios: handle 10 device ID PNP0e00 (000ed041)
PNPb003: adding fixed io range 0x220-0x233, size=0x14, align=0x1
PNPb003: adding fixed io range 0x330-0x331, size=0x2, align=0x1
PNPb003: adding fixed io range 0x388-0x389, size=0x2, align=0x1
PNPb003: adding irq mask 0x400
PNPb003: adding dma mask 0x2
PNPb003: adding dma mask 0x20
pnpbios: handle 11 device ID PNPb003 (03b0d041)
PNPb02f: adding fixed io range 0x200-0x207, size=0x8, align=0x1
pnpbios: handle 12 device ID PNPb02f (2fb0d041)
PNP0400: adding fixed io range 0x378-0x37b, size=0x4, align=0x1
PNP0400: adding irq mask 0x80
pnpbios: handle 13 device ID PNP0400 (0004d041)
PNP0500: adding fixed io range 0x3f8-0x3ff, size=0x8, align=0x1
PNP0500: adding irq mask 0x10
pnpbios: handle 14 device ID PNP0500 (0005d041)
PNP0500: adding fixed io range 0x2f8-0x2ff, size=0x8, align=0x1
PNP0500: adding irq mask 0x8
pnpbios: handle 15 device ID PNP0500 (0005d041)
PNP0700: adding fixed io range 0x3f0-0x3f5, size=0x6, align=0x1
PNP0700: adding fixed io range 0x3f7-0x3f7, size=0x1, align=0x1
PNP0700: adding irq mask 0x40
PNP0700: adding dma mask 0x4
pnpbios: handle 16 device ID PNP0700 (0007d041)
pnpbios: handle 17 device ID INT0016 (1600d425)
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xcf800-0xcffff,0xce800-0xcf7ff,0xc0000-0xc7fff on isa0
adv0 failed to probe on isa0
aha0: status reg test failed fe
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 failed to probe at port 0x134-0x137 on isa0
aic0 failed to probe at port 0x140-0x15f on isa0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x0000
ata0 at port 0x3f6,0x1f0-0x1f7 irq 14 on isa0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata1 at port 0x376,0x170-0x177 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fe
kbdc: RESET_KBD return code:00fe
kbdc: RESET_KBD return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
atkbd: failed to reset the keyboard.
device_probe_and_attach: atkbd0 attach returned 6
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
bt0: Failed Status Reg Test - fe
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 failed to probe at port 0x134-0x137 on isa0
cs0 failed to probe at port 0x300-0x31f on isa0
ed0 failed to probe at port 0x280-0x29f iomem 0xd8000 irq 10 on isa0
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0 failed to probe at port 0x300-0x31f on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
pmtimer0 on isa0
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc_detect_fifo: PWord not supported
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x3 0x13 0x3 0x3
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: irq maps: 0x3 0xb 0x3 0x3
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0 failed to probe at port 0x300-0x30f irq 10 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 60 4f 50 83 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 60 4f 50 83 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 60 4f 50 83 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0 failed to probe on isa0
isa_probe_children: probing PnP devices
psmcpnp0: <PS/2 mouse port> at irq 12 on isa0
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 90 03 3c
psm: status 90 03 3c
psm: status 90 03 3c
psm: data 08 00 00
psm: status 00 00 3c
psm: status 00 02 64
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
adv1: Invalid baseport of 0x0 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x40 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x70 specified. Nearest valid baseport is 0x100. Failing probe.
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is 0x100. Failing probe.
unknown: <PNP0800> failed to probe at port 0x61 on isa0
adv1: Invalid baseport of 0xf0 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x3e0 specified. Nearest valid baseport is 0x330. Failing probe.
unknown: <PNP0e00> failed to probe at port 0x3e0-0x3ef on isa0
adv1: Invalid baseport of 0x220 specified. Nearest valid baseport is 0x230. Failing probe.
unknown: <PNPb003> failed to probe at port 0x388-0x389,0x330-0x331,0x220-0x233 irq 10 drq 5,1 on isa0
adv1: Invalid baseport of 0x200 specified. Nearest valid baseport is 0x210. Failing probe.
unknown: <PNPb02f> failed to probe at port 0x200-0x20f on isa0
unknown: <PNP0400> can't assign resources (port)
unknown: <PNP0400> at port 0x378-0x37b on isa0
unknown: <PNP0500> can't assign resources (port)
unknown: <PNP0500> at port 0x3f8-0x3ff on isa0
unknown: <PNP0500> can't assign resources (port)
unknown: <PNP0500> at port 0x2f8-0x2ff on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0
unknown: <INT0016> failed to probe on isa0
SMP: enabled INTs: 3, 4, 6, 7, 9, 10, 11, 12, 14, 15, apic_imen: 0xffff2127
BIOS Geometries:
0:0223fe3f 0..547=548 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
procfs registered
Timecounters tick every 10.000 msec
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
bpf: lo0 attached
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
g_do_event(0xc0bd5d40) 3 m:0 g:0 p:0 c:0 -
g_post_event(1, 0, 0, 0xc19a4680, 0)
g_do_event(0xc193ad40) 1 m:0 g:0 p:0xc19a4680 c:0 -
EV_NEW_PROVIDER(geom.ctl)
g_mbrext_taste(MBREXT,geom.ctl)
mbr_taste(MBR,geom.ctl)
g_std_spoiled(0xc193ae00)
g_detach(0xc193ae00)
g_destroy_consumer(0xc193ae00)
g_destroy_geom(0xc19a4600(geom.ctl))
bsd_taste(BSD,geom.ctl)
g_std_spoiled(0xc193aec0)
g_detach(0xc193aec0)
g_destroy_consumer(0xc193aec0)
g_destroy_geom(0xc19a4400(geom.ctl))
dev_taste(DEV,geom.ctl)
(ahc1:A:0:0): Received WDTR 1 filtered to 0
(ahc1:A:0:0): Target Initiated WDTR
(ahc1:A:0:0): Sending WDTR 0
(ahc1:A:0:0): Received SDTR period c, offset f
Filtered to period 0, offset 0
(ahc1:A:0:0): Target Initiated SDTR
(ahc1:A:0:0): Sending SDTR period 0, offset 0
(probe7:ahc1:0:0:0): Retrying Command
(probe11:ahc1:0:4:0): error 22
(probe11:ahc1:0:4:0): Unretryable Error
(ahc1:A:4:0): Sending SDTR period c, offset f
(ahc1:A:4:0): Received SDTR period 32, offset f
Filtered to period 32, offset f
ahc1: target 4 synchronous at 5.0MHz, offset = 0xf
(ahc1:A:4:0): Sending SDTR period 32, offset f
(ahc1:A:4:0): Received SDTR period 32, offset f
Filtered to period 32, offset f
(ahc1:A:0:0): Sending WDTR 1
(ahc1:A:0:0): Received WDTR 1 filtered to 1
ahc1: target 0 using 16bit transfers
(ahc1:A:0:0): Sending SDTR period c, offset 8
(ahc1:A:0:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
ahc1: target 0 synchronous at 20.0MHz, offset = 0x8
g_call_me(0xc02ac740, 0xc1982300
pass0 at ahc1 bus 0 target 0 lun 0
pass0: <IBM DDRS-34560W S98G> Fixed Direct Access SCSI-2 device
pass0: Serial Number RDJ25018
pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
pass1 at ahc1 bus 0 target 4 lun 0
pass1: <MATSHITA CD-ROM CR-506 IG04> Removable CD-ROM SCSI-2 device
pass1: 5.000MB/s transfers (5.000MHz, offset 15)
(ahc1:A:4:0): Sending SDTR period 32, offset f
g_do_event(0xc0bd5d40) 3 m:0 g:0 p:0 c:0 -
g_post_event(1, 0, 0, 0xc19a4e00, 0)
g_do_event(0xc193ab40) 1 m:0 g:0 p:0xc19a4e00 c:0 -
EV_NEW_PROVIDER(da0)
g_mbrext_taste(MBREXT,da0)
mbr_taste(MBR,da0)
SMP: AP CPU #1 Launched!
SMP: CPU1 ap_init():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
Mounting root from ufs:/dev/da0s3a
g_dev_clone(da0s3a)
(ahc1:A:4:0): Received SDTR period 32, offset f
Filtered to period 32, offset f
(cd0:ahc1:0:4:0): error 6
(cd0:ahc1:0:4:0): Unretryable Error
cd0 at ahc1 bus 0 target 4 lun 0
cd0: <MATSHITA CD-ROM CR-506 IG04> Removable CD-ROM SCSI-2 device
cd0: 5.000MB/s transfers (5.000MHz, offset 15)
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0 at ahc1 bus 0 target 0 lun 0
da0: <IBM DDRS-34560W S98G> Fixed Direct Access SCSI-2 device
da0: Serial Number RDJ25018
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 4303MB (8813870 512 byte sectors: 255H 63S/T 548C)
g_slice_addslice()
g_post_event(1, 0, 0, 0xc19dba00, 0)
g_slice_addslice()
g_post_event(1, 0, 0, 0xc19db980, 0)
g_slice_addslice()
g_post_event(1, 0, 0, 0xc19db900, 0)
g_slice_addslice()
g_post_event(1, 0, 0, 0xc19db880, 0)
bsd_taste(BSD,da0)
g_std_spoiled(0xc19dec40)
g_detach(0xc19dec40)
g_destroy_consumer(0xc19dec40)
g_destroy_geom(0xc19db800(da0))
dev_taste(DEV,da0)
g_do_event(0xc19ded80) 1 m:0 g:0 p:0xc19dba00 c:0 -
EV_NEW_PROVIDER(da0s1)
g_mbrext_taste(MBREXT,da0s1)
0000 00 01 41 9d 82 fe 7f ab 3f 00 00 00 10 ad 03 00 |..A.....?.......|
[0] f:00 typ:130 s(CHS):157/1/65 e(CHS):171/254/127 s:63 l:240912
0000 00 00 41 ac 05 fe 7f b7 4f ad 03 00 0c f1 02 00 |..A.....O.......|
[1] f:00 typ:5 s(CHS):172/0/65 e(CHS):183/254/127 s:240975 l:192780
g_slice_addslice()
g_post_event(1, 0, 0, 0xc19a4400, 0)
0000 80 01 41 ac 83 fe 7f b7 3f 00 00 00 cd f0 02 00 |..A.....?.......|
[0] f:80 typ:131 s(CHS):172/1/65 e(CHS):183/254/127 s:63 l:192717
0000 00 00 41 b8 05 fe 7f c1 5b 9e 06 00 8a 73 02 00 |..A.....[....s..|
[1] f:00 typ:5 s(CHS):184/0/65 e(CHS):193/254/127 s:433755 l:160650
0000 00 01 41 b8 83 fe 7f c1 3f 00 00 00 4b 73 02 00 |..A.....?...Ks..|
[0] f:00 typ:131 s(CHS):184/1/65 e(CHS):193/254/127 s:63 l:160587
0000 00 00 41 c2 05 fe bf 0a e5 11 09 00 09 e5 11 00 |..A.............|
[1] f:00 typ:5 s(CHS):194/0/65 e(CHS):10/254/191 s:594405 l:1172745
g_slice_addslice()
g_post_event(1, 0, 0, 0xc19db580, 0)
0000 00 01 41 c2 83 fe bf 0a 3f 00 00 00 ca e4 11 00 |..A.....?.......|
[0] f:00 typ:131 s(CHS):194/1/65 e(CHS):10/254/191 s:63 l:1172682
0000 00 00 81 0b 05 fe bf 23 ee f6 1a 00 d9 20 06 00 |.......#..... ..|
[1] f:00 typ:5 s(CHS):11/0/129 e(CHS):35/254/191 s:1767150 l:401625
g_slice_addslice()
g_post_event(1, 0, 0, 0xc19db500, 0)
0000 00 01 81 0b 83 fe bf 23 3f 00 00 00 9a 20 06 00 |.......#?.... ..|
[0] f:00 typ:131 s(CHS):11/1/129 e(CHS):35/254/191 s:63 l:401562
0000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
g_slice_addslice()
g_post_event(1, 0, 0, 0xc19a4600, 0)
mbr_taste(MBR,da0s1)
g_std_spoiled(0xc19dea80)
g_detach(0xc19dea80)
g_destroy_consumer(0xc19dea80)
g_destroy_geom(0xc19db480(da0s1))
bsd_taste(BSD,da0s1)
g_std_spoiled(0xc194b000)
g_detach(0xc194b000)
g_destroy_consumer(0xc194b000)
g_destroy_geom(0xc19db480(da0s1))
dev_taste(DEV,da0s1)
g_do_event(0xc19ded40) 1 m:0 g:0 p:0xc19db980 c:0 -
EV_NEW_PROVIDER(da0s2)
g_mbrext_taste(MBREXT,da0s2)
g_std_spoiled(0xc19de9c0)
g_detach(0xc19de9c0)
g_destroy_consumer(0xc19de9c0)
g_destroy_geom(0xc19db280(da0s2))
mbr_taste(MBR,da0s2)
g_std_spoiled(0xc194b080)
g_detach(0xc194b080)
g_destroy_consumer(0xc194b080)
g_destroy_geom(0xc19a4a80(da0s2))
bsd_taste(BSD,da0s2)
g_std_spoiled(0xc19de940)
g_detach(0xc19de940)
g_destroy_consumer(0xc19de940)
g_destroy_geom(0xc19db180(da0s2))
dev_taste(DEV,da0s2)
g_do_event(0xc19ded00) 1 m:0 g:0 p:0xc19db900 c:0 -
EV_NEW_PROVIDER(da0s3)
g_mbrext_taste(MBREXT,da0s3)
g_std_spoiled(0xc19de880)
g_detach(0xc19de880)
g_destroy_consumer(0xc19de880)
g_destroy_geom(0xc19db080(da0s3))
mbr_taste(MBR,da0s3)
g_std_spoiled(0xc194b100)
g_detach(0xc194b100)
g_destroy_consumer(0xc194b100)
g_destroy_geom(0xc19b6000(da0s3))
bsd_taste(BSD,da0s3)
g_slice_config(da0s3, 0, 0)
g_slice_config(da0s3, 1, 0)
g_slice_config(da0s3, 2, 0)
g_slice_config(da0s3, 3, 0)
g_slice_config(da0s3, 4, 0)
g_slice_config(da0s3, 5, 0)
g_slice_config(da0s3, 6, 0)
g_slice_config(da0s3, 7, 0)
g_slice_config(da0s3, 0, 1)
g_post_event(1, 0, 0, 0xc19b6e80, 0)
g_slice_config(da0s3, 1, 1)
g_post_event(1, 0, 0, 0xc19b6e00, 0)
g_slice_config(da0s3, 2, 1)
g_post_event(1, 0, 0, 0xc19b6d80, 0)
g_slice_config(da0s3, 3, 1)
g_slice_config(da0s3, 4, 1)
g_post_event(1, 0, 0, 0xc19b6d00, 0)
g_slice_config(da0s3, 5, 1)
g_post_event(1, 0, 0, 0xc19b6c80, 0)
g_slice_config(da0s3, 6, 1)
g_slice_config(da0s3, 7, 1)
dev_taste(DEV,da0s3)
g_do_event(0xc19decc0) 1 m:0 g:0 p:0xc19db880 c:0 -
EV_NEW_PROVIDER(da0s4)
g_mbrext_taste(MBREXT,da0s4)
g_std_spoiled(0xc19de600)
g_detach(0xc19de600)
g_destroy_consumer(0xc19de600)
g_destroy_geom(0xc19b6b80(da0s4))
mbr_taste(MBR,da0s4)
g_std_spoiled(0xc193ac80)
g_detach(0xc193ac80)
g_destroy_consumer(0xc193ac80)
g_destroy_geom(0xc19a4d00(da0s4))
bsd_taste(BSD,da0s4)
g_std_spoiled(0xc194b3c0)
g_detach(0xc194b3c0)
g_destroy_consumer(0xc194b3c0)
g_destroy_geom(0xc19a4a00(da0s4))
dev_taste(DEV,da0s4)
g_do_event(0xc194b540) 1 m:0 g:0 p:0xc19a4400 c:0 -
EV_NEW_PROVIDER(da0s5)
g_mbrext_taste(MBREXT,da0s5)
mbr_taste(MBR,da0s5)
g_std_spoiled(0xc19de540)
g_detach(0xc19de540)
g_destroy_consumer(0xc19de540)
g_destroy_geom(0xc19b6a00(da0s5))
bsd_taste(BSD,da0s5)
g_std_spoiled(0xc194b500)
g_detach(0xc194b500)
g_destroy_consumer(0xc194b500)
g_destroy_geom(0xc19a4980(da0s5))
dev_taste(DEV,da0s5)
g_do_event(0xc19deb40) 1 m:0 g:0 p:0xc19db580 c:0 -
EV_NEW_PROVIDER(da0s6)
g_mbrext_taste(MBREXT,da0s6)
mbr_taste(MBR,da0s6)
g_std_spoiled(0xc194b380)
g_detach(0xc194b380)
g_destroy_consumer(0xc194b380)
g_destroy_geom(0xc19a4780(da0s6))
bsd_taste(BSD,da0s6)
g_std_spoiled(0xc19de4c0)
g_detach(0xc19de4c0)
g_destroy_consumer(0xc19de4c0)
g_destroy_geom(0xc19b6880(da0s6))
dev_taste(DEV,da0s6)
g_do_event(0xc19deb00) 1 m:0 g:0 p:0xc19db500 c:0 -
EV_NEW_PROVIDER(da0s7)
g_mbrext_taste(MBREXT,da0s7)
mbr_taste(MBR,da0s7)
g_std_spoiled(0xc19de400)
g_detach(0xc19de400)
g_destroy_consumer(0xc19de400)
g_destroy_geom(0xc19b6780(da0s7))
bsd_taste(BSD,da0s7)
g_std_spoiled(0xc194b680)
g_detach(0xc194b680)
g_destroy_consumer(0xc194b680)
g_destroy_geom(0xc19b6780(da0s7))
dev_taste(DEV,da0s7)
g_do_event(0xc194b240) 1 m:0 g:0 p:0xc19a4600 c:0 -
EV_NEW_PROVIDER(da0s8)
g_mbrext_taste(MBREXT,da0s8)
mbr_taste(MBR,da0s8)
g_std_spoiled(0xc194b500)
g_detach(0xc194b500)
g_destroy_consumer(0xc194b500)
g_destroy_geom(0xc19b6a00(da0s8))
bsd_taste(BSD,da0s8)
g_std_spoiled(0xc19de380)
g_detach(0xc19de380)
g_destroy_consumer(0xc19de380)
g_destroy_geom(0xc19a4780(da0s8))
dev_taste(DEV,da0s8)
g_do_event(0xc19de7c0) 1 m:0 g:0 p:0xc19b6e80 c:0 -
EV_NEW_PROVIDER(da0s3a)
g_mbrext_taste(MBREXT,da0s3a)
mbr_taste(MBR,da0s3a)
g_std_spoiled(0xc19de2c0)
g_detach(0xc19de2c0)
g_destroy_consumer(0xc19de2c0)
g_destroy_geom(0xc19a4d00(da0s3a))
bsd_taste(BSD,da0s3a)
dev_taste(DEV,da0s3a)
g_do_event(0xc19de780) 1 m:0 g:0 p:0xc19b6e00 c:0 -
EV_NEW_PROVIDER(da0s3b)
g_mbrext_taste(MBREXT,da0s3b)
mbr_taste(MBR,da0s3b)
g_std_spoiled(0xc19de200)
g_detach(0xc19de200)
g_destroy_consumer(0xc19de200)
g_destroy_geom(0xc19db480(da0s3b))
bsd_taste(BSD,da0s3b)
dev_taste(DEV,da0s3b)
g_do_event(0xc19de740) 1 m:0 g:0 p:0xc19b6d80 c:0 -
EV_NEW_PROVIDER(da0s3c)
g_mbrext_taste(MBREXT,da0s3c)
mbr_taste(MBR,da0s3c)
g_std_spoiled(0xc19de880)
g_detach(0xc19de880)
g_destroy_consumer(0xc19de880)
g_destroy_geom(0xc19db480(da0s3c))
bsd_taste(BSD,da0s3c)
dev_taste(DEV,da0s3c)
g_do_event(0xc19de700) 1 m:0 g:0 p:0xc19b6d00 c:0 -
EV_NEW_PROVIDER(da0s3e)
g_mbrext_taste(MBREXT,da0s3e)
mbr_taste(MBR,da0s3e)
g_std_spoiled(0xc19de180)
g_detach(0xc19de180)
g_destroy_consumer(0xc19de180)
g_destroy_geom(0xc19a4780(da0s3e))
bsd_taste(BSD,da0s3e)
dev_taste(DEV,da0s3e)
g_do_event(0xc19de6c0) 1 m:0 g:0 p:0xc19b6c80 c:0 -
EV_NEW_PROVIDER(da0s3f)
g_mbrext_taste(MBREXT,da0s3f)
mbr_taste(MBR,da0s3f)
g_std_spoiled(0xc19de0c0)
g_detach(0xc19de0c0)
g_destroy_consumer(0xc19de0c0)
g_destroy_geom(0xc19e3780(da0s3f))
bsd_taste(BSD,da0s3f)
dev_taste(DEV,da0s3f)
g_dev_clone(da0s3a) = 0xc19df800
g_post_event(2, 0, 0, 0xc19b6e80, 0xc19de280)
g_post_event(2, 0, 0, 0xc19db900, 0xc19de800)
g_post_event(2, 0, 0, 0xc19a4e00, 0xc0bd5d40)
g_do_event(0xc19de6c0) 2 m:0 g:0 p:0xc19b6e80 c:0xc19de280 -
EV_SPOILED(0xc19b6e80(da0s3a),0xc19de280)
g_do_event(0xc19de0c0) 2 m:0 g:0 p:0xc19db900 c:0xc19de800 -
EV_SPOILED(0xc19db900(da0s3),0xc19de800)
spoiling 0xc19de680 (da0s3) (0)
g_do_event(0xc19de740) 2 m:0 g:0 p:0xc19a4e00 c:0xc0bd5d40 -
EV_SPOILED(0xc19a4e00(da0),0xc0bd5d40)
spoiling 0xc19dec00 (da0) (0)
WARNING: / was not properly dismounted
start_init: trying /sbin/init
g_call_me(0xc02ac910, 0xc1903440
g_do_event(0xc19dee40) 3 m:0 g:0 p:0 c:0 -
g_call_me(0xc02ac910, 0xc1903460
g_do_event(0xc19dedc0) 3 m:0 g:0 p:0 c:0 -
g_call_me(0xc02ad140, 0xc1903480
g_do_event(0xc1a1ee40) 3 m:0 g:0 p:0 c:0 -
g_call_me(0xc02ad140, 0xc19034a0
g_do_event(0xc19deec0) 3 m:0 g:0 p:0 c:0 -
g_call_me(0xc02acc30, 0xc19034c0
g_do_event(0xc1a1df00) 3 m:0 g:0 p:0 c:0 -
g_call_me(0xc02acc30, 0xc19034e0
g_do_event(0xc1a1e000) 3 m:0 g:0 p:0 c:0 -
g_post_event(2, 0, 0, 0xc19b6e00, 0xc19de540)
g_do_event(0xc1a7b340) 2 m:0 g:0 p:0xc19b6e00 c:0xc19de540 -
EV_SPOILED(0xc19b6e00(da0s3b),0xc19de540)
g_dev_clone(devfs)
g_dev_clone(devfs)
g_dev_clone(devfs)
g_post_event(2, 0, 0, 0xc19b6c80, 0xc19dea80)
g_do_event(0xc1a7b040) 2 m:0 g:0 p:0xc19b6c80 c:0xc19dea80 -
EV_SPOILED(0xc19b6c80(da0s3f),0xc19dea80)
g_post_event(1, 0, 0, 0xc19b6c80, 0)
g_do_event(0xc193ac80) 1 m:0 g:0 p:0xc19b6c80 c:0 -
EV_NEW_PROVIDER(da0s3f)
g_mbrext_taste(MBREXT,da0s3f)
mbr_taste(MBR,da0s3f)
g_std_spoiled(0xc1a2cf40)
g_detach(0xc1a2cf40)
g_destroy_consumer(0xc1a2cf40)
g_destroy_geom(0xc1a33780(da0s3f))
bsd_taste(BSD,da0s3f)
g_dev_clone(devfs)
g_post_event(2, 0, 0, 0xc19b6d00, 0xc19de140)
g_do_event(0xc1a2ce40) 2 m:0 g:0 p:0xc19b6d00 c:0xc19de140 -
EV_SPOILED(0xc19b6d00(da0s3e),0xc19de140)
g_post_event(1, 0, 0, 0xc19b6d00, 0)
g_do_event(0xc1a2ce00) 1 m:0 g:0 p:0xc19b6d00 c:0 -
EV_NEW_PROVIDER(da0s3e)
g_mbrext_taste(MBREXT,da0s3e)
mbr_taste(MBR,da0s3e)
g_std_spoiled(0xc194b100)
g_detach(0xc194b100)
g_destroy_consumer(0xc194b100)
g_destroy_geom(0xc1a11900(da0s3e))
bsd_taste(BSD,da0s3e)
g_post_event(2, 0, 0, 0xc19b6c80, 0xc19dea80)
g_do_event(0xc1a1d580) 2 m:0 g:0 p:0xc19b6c80 c:0xc19dea80 -
EV_SPOILED(0xc19b6c80(da0s3f),0xc19dea80)
g_post_event(2, 0, 0, 0xc19b6d00, 0xc19de140)
g_do_event(0xc1a2c380) 2 m:0 g:0 p:0xc19b6d00 c:0xc19de140 -
EV_SPOILED(0xc19b6d00(da0s3e),0xc19de140)
g_dev_clone(tty[pqrsPQRS]*)
g_dev_clone(tty[pqrsPQRS]*)
g_dev_clone(log)
g_dev_clone(bpf0)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(log)
g_dev_clone(tty)
Linux ELF exec handler installed
g_dev_clone(vga)
g_dev_clone(vga)
g_dev_clone(vga)
g_dev_clone(vga)
g_dev_clone(devfs)
g_dev_clone(devfs)
g_dev_clone(devfs)
g_dev_clone(devfs)
-------------------------------------------------------------------------------
Finally, what mptable reports:
===============================================================================
MPTable, version 2.0.15
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000fbaa0
signature: '_MP_'
length: 16 bytes
version: 1.1
checksum: 0x9d
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x0009fd00
signature: 'PCMP'
base table length: 236
version: 1.1
checksum: 0xf2
OEM ID: 'INGR '
Product ID: 'RAPTOR '
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 21
local APIC address: 0xfee00000
extended table length: 0
extended table checksum: 0
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
1 0x11 BSP, usable 6 1 9 0xfbff
0 0x11 AP, usable 6 1 9 0xfbff
--
Bus: Bus ID Type
0 PCI
1 ISA
--
I/O APICs: APIC ID Version State Address
14 0x11 usable 0xfec00000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
INT conforms conforms 1 1 14 1
INT conforms conforms 1 0 14 2
INT conforms conforms 1 3 14 3
INT conforms conforms 1 4 14 4
INT conforms conforms 1 5 14 5
INT conforms conforms 1 6 14 6
INT conforms conforms 1 7 14 7
INT conforms conforms 1 8 14 8
INT conforms conforms 1 9 14 9
INT conforms conforms 1 10 14 10
INT conforms conforms 1 11 14 11
INT conforms conforms 1 12 14 12
INT conforms conforms 1 13 14 13
INT conforms conforms 1 14 14 14
INT conforms conforms 1 15 14 15
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
NMI conforms conforms 0 0:A 255 1
===============================================================================
The SMP kernel is just GENERIC with the usual SMP + APIC_IO options.
Cheers,
Mark.
--
Mark Valentine, Thuvia Labs <mark@thuvia.co.uk> <http://www.thuvia.co.uk>;
"Tigers will do ANYTHING for a tuna fish sandwich." Mark Valentine uses
"We're kind of stupid that way." *munch* *munch* and endorses FreeBSD
-- <http://www.calvinandhobbes.com>; <http://www.freebsd.org>;
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-smp" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200210251654.g9PGsIK5074910>