Date: Mon, 28 Jan 2008 21:10:40 -0500 From: "Bhuvaneswari Ramkumar" <ramkumar@iastate.edu> To: "Giorgos Keramidas" <keramida@ceid.upatras.gr> Cc: freebsd-questions@freebsd.org, ccowart@rescomp.berkeley.edu Subject: Re: Network configuration in FreeBSD Message-ID: <7c7927920801281810o17d39136qbc49b8c2ea44719@mail.gmail.com> In-Reply-To: <7c7927920801281803r87b733epb6788f93e6ac512d@mail.gmail.com> References: <7c7927920801281329n609abb8ah63a18f1afb56099d@mail.gmail.com> <20080128214202.GO41095@hal.rescomp.berkeley.edu> <7c7927920801281518h5adfb91dta827fcae39ebc09a@mail.gmail.com> <20080129010633.GA6442@kobe.laptop> <7c7927920801281803r87b733epb6788f93e6ac512d@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
the netstat reads: #netstat -nr Routing tables Internet: Destination Gateway Flags REfs Use Netif Expire 127.0.0.1 127.0.0.1 UH 0 41 lo0 Internet 6 Destination Gateway Flags Netif Expire ::1 ::1 UH lo0 fe80::%lo0/64 fe80::1%lo0 U lo0 fe80::1%lo0 link#3 UHL lo0 ff01::/32 ::1 U lo0 ff02 :: %lo0/32 ::1 UC lo0 On Mon, Jan 28, 2008 at 9:03 PM, Bhuvaneswari Ramkumar <ramkumar@iastate.edu> wrote: > ok here u go, the exact output of the the commands: > > #ifconfig -a > > em0: flags=8802<BROADCAST, SIMPLEX, MULTICAST> mtu 1500 > options=b<RXSCUM, TXSCUM, VLAN_MTU> > ether :0d:56:f0:f1:ba > media:Ethernet autoselect (100baseTX <full-duplex>) > status: active > > plip0:flags=108810<POINTTOPOINT,SIMPLEX,MULTICAST> mtu 1500 > lo0:flags=8049<UP, LOOPBACK,RUNNING,MULTICAST> MTU 16384 > inet 127.0.0.1 netmask 0xff000000 > inet ::1 prefixlen 128 > inet6 fe80 :: 1% lo0 prefixlen 64 scopeid 0x3 > > > On Mon, Jan 28, 2008 at 8:06 PM, Giorgos Keramidas < > keramida@ceid.upatras.gr> wrote: > > > On 2008-01-28 18:18, Bhuvaneswari Ramkumar <ramkumar@iastate.edu> wrote: > > > On Mon, Jan 28, 2008 at 4:42 PM, Christopher Cowart < > > ccowart@rescomp.berkeley.edu> wrote: > > > > > > > > Send the list the output of the following commands: > > > > # ifconfig -a > > > > # netstat -rn > > > > > > > > With that info, we can probably help you out better. > > > > > > ifconfig -a > > > > > > em0: flags .......lot of data ..................... > > > status: active > > > > > > ( I'm guessing this is the ethernet interface) > > > > > > netstat -rn > > > > > > routing tables: > > > Internet : > > > 127.0.0.1 ..followed by some IPs, flags(UH), etc .. > > > > > > Internet6 > > > expire followed by some hex-values and flags > > > > > > would this do or more specifics needed ? > > > > Not really, no. You are supposed to show the *exact* output of > > commands, if you expect more useful answers. > > > > Now, I understand that without networking, it may be tricky to capture > > the output and post it in an email message. > > > > If you have a floppy disk you can use the floppy to capture the output > > of these commands, i.e. by mounting it: > > > > # cd /root > > # mount -t msdosfs /dev/fd0 /mnt > > # ifconfig -a > /mnt/ifconfig.txt > > # netstat -rn > /mnt/netstat.txt > > # umount /mnt > > > > If you have a USB flash drive, you can mount that too (assuming it has a > > single FAT partition): > > > > ( plug the USB flash disk into a USB socket ) > > > > # cd /root > > # mount -t msdosfs /dev/da0s1 /mnt > > # ifconfig -a > /mnt/ifconfig.txt > > # netstat -rn > /mnt/netstat.txt > > # umount /mnt > > > > ( unplug the flash disk ) > > > > It will help immensely if you post the *exact* output of the commands > > mentioned by Christopher. > > > > - Giorgos > > > > _______________________________________________ > > freebsd-questions@freebsd.org mailing list > > http://lists.freebsd.org/mailman/listinfo/freebsd-questions > > To unsubscribe, send any mail to " > > freebsd-questions-unsubscribe@freebsd.org" > > > >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?7c7927920801281810o17d39136qbc49b8c2ea44719>