Date: Mon, 16 Jan 2006 10:53:23 -0800 From: Aaron Burruss <aburruss@gmail.com> To: freebsd-questions@freebsd.org Subject: Re: External USB drive on Sun HW Message-ID: <1f1368120601161053y5d23eb31hc66b37f43ba52d8b@mail.gmail.com> In-Reply-To: <1f1368120601131607n643aeb2cx7ab781dd9a9c76ae@mail.gmail.com> References: <1f1368120601131607n643aeb2cx7ab781dd9a9c76ae@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Anyone have any ideas here? On 1/13/06, Aaron Burruss <aburruss@gmail.com> wrote: > > Hi there, > > I'm looking for some help on a problem I'm having with a new setup I've > got... I'm running sparc64 6.0 and also have an external USB drive > enclosure with a 250GB IDE drive in it. The drive is formatted as a BSD > partition (formatting done on another box). > > I've got the following in my kernel: > > # USB support > device uhci # UHCI PCI->USB interface > device ohci # OHCI PCI->USB interface > device usb # USB Bus (required) > device ugen # Generic > device uhid # "Human Interface Devices" > device umass # Disks/Mass storage - Requires scbus and da > > I.m seeing this in dmesg: > > > root@sun# dmesg |grep -i umass > umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2 > umass0: BBB reset failed, TIMEOUT > umass0: BBB bulk-in clear stall failed, TIMEOUT > umass0: BBB bulk-out clear stall failed, TIMEOUT > umass0: BBB reset failed, TIMEOUT > umass0: BBB bulk-in clear stall failed, TIMEOUT > umass0: BBB bulk-out clear stall failed, TIMEOUT > umass0: BBB reset failed, TIMEOUT > umass0: BBB bulk-in clear stall failed, TIMEOUT > umass0: BBB bulk-out clear stall failed, TIMEOUT > umass0: BBB reset failed, TIMEOUT > umass0: BBB bulk-in clear stall failed, TIMEOUT > umass0: BBB bulk-out clear stall failed, TIMEOUT > umass0: BBB reset failed, TIMEOUT > umass0: BBB bulk-in clear stall failed, TIMEOUT > umass0: BBB bulk-out clear stall failed, TIMEOUT > root@sun# dmesg|grep -i usb > ohci0: <Sun PCIO-2 USB controller> mem 0xe2000000-0xe2007fff at device > 12.3 on pci1 > usb0: OHCI version 1.0, legacy support > usb0: <Sun PCIO-2 USB controller> on ohci0 > usb0: USB revision 1.0 > ohci1: <Sun PCIO-2 USB controller> mem 0xe5000000-0xe5007fff at device 5.= 3on pci1 > usb1: OHCI version 1.0, legacy support > usb1: <Sun PCIO-2 USB controller> on ohci1 > usb1: USB revision 1.0 > umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2 > usbdevs shows: root@sun# usbdevs -v Controller /dev/usb0: addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), (0x108e)(0x0000), rev 1.00 port 1 powered port 2 powered port 3 powered port 4 powered Controller /dev/usb1: addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), (0x108e)(0x0000), rev 1.00 port 1 addr 2: full speed, self powered, config 1, product 0x0702(0x0702), vendor 0x05e3(0x05e3), rev 0.33 port 2 powered port 3 powered port 4 powered My primary hard drives are da0 and da1 (all the how-to's say that daX > should be where I mount.. but /dev only has my two primary drives: > > -su-2.05b# ls -la /dev/da* > crw-r----- 1 root operator 4, 16 Dec 20 20:11 /dev/da0 > crw-r----- 1 root operator 4, 18 Dec 20 12:11 /dev/da0a > crw-r----- 1 root operator 4, 19 Dec 20 20:11 /dev/da0b > crw-r----- 1 root operator 4, 20 Dec 20 20:11 /dev/da0c > crw-r----- 1 root operator 4, 17 Dec 20 20:11 /dev/da1 > crw-r----- 1 root operator 4, 21 Dec 20 20:11 /dev/da1c > crw-r----- 1 root operator 4, 22 Dec 20 12:11 /dev/da1d > > -su-2.05b# dmesg|grep da.: > da0: <FUJITSU MAN3367M SUN36G 1502> Fixed Direct Access SCSI-2 device > da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing > Enabled > da0: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C) > da1: <FUJITSU MAN3367M SUN36G 1502> Fixed Direct Access SCSI-2 device > da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing > Enabled > da1: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C) > > I can plug this into my AMD64 running FreeBSD 6, and it comes up with no > problems. > > I THINK I'm probably missing something totally dumb... Anyone got any hel= p > for me on this? > > Yah.. I know.. get an i386 box with IDE drives. :) This is a small 1U > box, and fits in my closet well. so I'd like to use it if possible. > > Thanks!!! > Aaron > >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1f1368120601161053y5d23eb31hc66b37f43ba52d8b>