Date: Tue, 01 Oct 2002 22:03:35 -0400 (EDT) From: John Baldwin <jhb@FreeBSD.org> To: Alexander Langer <alex@big.endian.de> Cc: current@FreeBSD.org Subject: RE: kernel boot messages absent Message-ID: <XFMail.20021001220335.jhb@FreeBSD.org> In-Reply-To: <20021002002620.GJ85009@fump.kawo2.rwth-aachen.de>
next in thread | previous in thread | raw e-mail | index | archive | help
On 02-Oct-2002 Alexander Langer wrote: > Hi! > > Can anyone explain me why with a recent kernel (last kernel was from > 1 year ago) the kernel boot messages disappear from the monitor > once the "propellor" of the kernel boot has done like 5 rounds > (last message is the last line of the > "Booting kernel in X seconds" line, followed by a single "-" on > the line, which used to be the propellor) You need to setup a /boot/device.hints file if you haven't already so that the kernel can configure it's console device. > > It seems a bit like the kernel is thinking it boots from > a serial console (not tried due to the lack of a serial cable, though). > > However, once the getty is started, the login prompt is shown on > the monitor as it should. > > I've tried to tell the loader in loader.conf that console="vidconsole", > but it doesn't help. Note that the loader itself is visible. > > This is the dmesg from boot -v. I've got no idea :-( Odd. > > Thanks for any pointers > > ... > Uptime: 7h19m56s > Terminate ACPI > Rebooting... > Copyright (c) 1992-2002 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.0-CURRENT #1: Tue Oct 1 15:35:39 CEST 2002 > alex@mobile.cichlids.com:/usr/obj/usr/src/sys/GENERIC > Preloaded elf kernel "/boot/kernel/kernel" at 0xc06a7000. > Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06a70b4. > Calibrating clock(s) ... TSC clock: 647190907 Hz, i8254 clock: 1193189 Hz > CLK_USE_I8254_CALIBRATION not specified - using default frequency > Timecounter "i8254" frequency 1193182 Hz > CLK_USE_TSC_CALIBRATION not specified - using old calibration method > Timecounter "TSC" frequency 647189786 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (647.19-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x683 Stepping = 3 > > Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR, > SSE> > real memory = 201261056 (196544K bytes) > Physical memory chunk(s): > 0x00001000 - 0x0009efff, 647168 bytes (158 pages) > 0x006ce000 - 0x0bfe7fff, 194093056 bytes (47386 pages) > avail memory = 188153856 (183744K bytes) > bios32: Found BIOS32 Service Directory header at 0xc00f6a90 > bios32: Entry = 0xfd8c0 (c00fd8c0) Rev = 0 Len = 1 > pcibios: PCI BIOS entry at 0xfd8c0+0x11e > pnpbios: Found PnP BIOS data at 0xc00f6ac0 > pnpbios: Entry = f0000:8da2 Rev = 1.0 > Other BIOS signatures found: > random: <entropy source> > mem: <memory & I/O> > Pentium Pro MTRR support enabled > null: <null device, zero device> > npx0: <math processor> on motherboard > npx0: INT 16 interface > acpi0: <PTLTD RSDT > on motherboard > pci_open(1): mode 1 addr port (0x0cf8) is 0x80003904 > pci_open(1a): mode1res=0x80000000 (0x80000000) > pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086) > Using $PIR table, 4 entries at 0xc00fdf80 > PCI-Only Interrupts: none > Location Bus Device Pin Link IRQs > embedded 0 7 D 0x63 3 4 11 > embedded 0 12 A 0x60 3 4 11 > embedded 0 9 A 0x62 3 4 5 > embedded 0 1 A 0x61 3 4 10 11 > ACPI timer looks BAD min = 1, max = 5, width = 5 > ACPI timer looks BAD min = 2, max = 5, width = 4 > ACPI timer looks BAD min = 1, max = 16777213, width = 16777213 > ACPI timer looks BAD min = 1, max = 5, width = 5 > ACPI timer looks BAD min = 2, max = 5, width = 4 > ACPI timer looks BAD min = 2, max = 5, width = 4 > ACPI timer looks BAD min = 2, max = 16777213, width = 16777212 > ACPI timer looks BAD min = 1, max = 6, width = 6 > ACPI timer looks BAD min = 1, max = 5, width = 5 > ACPI timer looks BAD min = 1, max = 5, width = 5 > Timecounter "ACPI-safe" frequency 3579545 Hz > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 > acpi_cpu0: <CPU> on acpi0 > acpi_tz0: <thermal zone> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pci0: physical bus=0 > map[10]: type 3, range 32, base f8000000, size 26, enabled > found-> vendor=0x8086, dev=0x7190, revid=0x03 > bus=0, slot=0, func=0 > class=06-00-00, hdrtype=0x00, mfdev=0 > found-> vendor=0x8086, dev=0x7191, revid=0x03 > bus=0, slot=1, func=0 > class=06-04-00, hdrtype=0x01, mfdev=0 > found-> vendor=0x8086, dev=0x7110, revid=0x02 > bus=0, slot=7, func=0 > class=06-80-00, hdrtype=0x00, mfdev=1 > map[20]: type 4, range 32, base 00001050, size 4, enabled > found-> vendor=0x8086, dev=0x7111, revid=0x01 > bus=0, slot=7, func=1 > class=01-01-80, hdrtype=0x00, mfdev=0 > map[20]: type 4, range 32, base 00001060, size 5, port disabled > found-> vendor=0x8086, dev=0x7112, revid=0x01 > bus=0, slot=7, func=2 > class=0c-03-00, hdrtype=0x00, mfdev=0 > intpin=d, irq=255 > map[90]: type 4, range 32, base 00001040, size 4, enabled > found-> vendor=0x8086, dev=0x7113, revid=0x02 > bus=0, slot=7, func=3 > class=06-80-00, hdrtype=0x00, mfdev=0 > map[10]: type 4, range 32, base 00001080, size 7, port disabled > found-> vendor=0x4005, dev=0x0308, revid=0x00 > bus=0, slot=9, func=0 > class=04-01-00, hdrtype=0x00, mfdev=1 > intpin=a, irq=255 > powerspec 2 supports D0 D2 D3 current D0 > map[10]: type 4, range 32, base 00001400, size 2, port disabled > found-> vendor=0x4005, dev=0x0309, revid=0x00 > bus=0, slot=9, func=1 > class=09-80-00, hdrtype=0x00, mfdev=1 > powerspec 2 supports D0 D3 current D0 > map[10]: type 1, range 32, base 88000000, size 12, enabled > found-> vendor=0x1180, dev=0x0475, revid=0x80 > bus=0, slot=12, func=0 > class=06-07-00, hdrtype=0x02, mfdev=0 > intpin=a, irq=255 > powerspec 1 supports D0 D1 D2 D3 current D0 > agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xf8000000-0xfbffffff at device 0.0 on pci0 > agp0: allocating GATT for aperture of size 64M > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pcib1: secondary bus 1 > pcib1: subordinate bus 1 > pcib1: I/O decode 0x2000-0x2fff > pcib1: memory decode 0xfc000000-0xfdffffff > pcib1: prefetched decode 0xfff00000-0xfffff > pcib1: could not get PCI interrupt routing table - AE_NOT_FOUND > pci1: <ACPI PCI bus> on pcib1 > pci1: physical bus=1 > map[10]: type 1, range 32, base fd000000, size 24, enabled > map[14]: type 4, range 32, base 00002000, size 8, enabled > map[18]: type 1, range 32, base fc000000, size 12, enabled > found-> vendor=0x1002, dev=0x4c42, revid=0xdc > bus=1, slot=0, func=0 > class=03-00-00, hdrtype=0x00, mfdev=0 > powerspec 1 supports D0 D1 D2 D3 current D0 > pci1: <display, VGA> at device 0.0 (no driver attached) > PCI-ISA bridge with incorrect subclass 0x80 > PCI-ISA bridge with incorrect subclass 0x80 > isab0: <PCI-ISA bridge> at device 7.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel PIIX4 ATA33 controller> port 0x1050-0x105f at device 7.1 on pci0 > ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1050 > ata0: mask=03 ostat0=50 ostat2=00 > ata0-master: ATAPI 00 00 > ata0-slave: ATAPI 00 00 > ata0: mask=03 stat0=50 stat1=00 > ata0-master: ATA 01 a5 > ata0: devices=01 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1058 > ata1: mask=03 ostat0=25 ostat2=25 > ata1-master: ATAPI 25 25 > ata1-slave: ATAPI 25 25 > ata1: mask=03 stat0=25 stat1=25 > ata1-master: ATA 25 25 > ata1-slave: ATA 25 25 > ata1: devices=00 > ata1: at 0x170 irq 15 on atapci0 > uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1060-0x107f at device 7.2 on pci0 > pcib0: matched entry for 0.7.INTD (source \\_SB_.PCI0.ISA_.LNKD) > pcib0: possible interrupts: 3 4 5 7 11 12 > pcib0: slot 7 INTD routed to irq 3 via \\_SB_.PCI0.ISA_.LNKD > usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) > pci0: <multimedia, audio> at device 9.0 (no driver attached) > pci0: <input device> at device 9.1 (no driver attached) > cbb0: <RF5C475 PCI-CardBus Bridge> mem 0x88000000-0x88000fff at device 12.0 on pci0 > cardbus0: <CardBus bus> on cbb0 > pccard0: <16-bit PCCard bus> on cbb0 > pcib0: matched entry for 0.12.INTA (source \\_SB_.PCI0.ISA_.LNKA) > pcib0: possible interrupts: 3 4 5 7 11 12 > pcib0: slot 12 INTA routed to irq 3 via \\_SB_.PCI0.ISA_.LNKA > acpi_acad0: <AC adapter> on acpi0 > acpi_cmbat0: <Control method Battery> on acpi0 > acpi_lid0: <Control Method Lid Switch> on acpi0 > acpi_button0: <Sleep Button> on acpi0 > acpi_button1: <Power Button> on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > atkbd: the current kbd controller command byte 0047 > atkbd: keyboard ID 0x41ab (2) > kbd0 at atkbd0 > kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000 > psm0: unable to allocate IRQ > psmcpnp0 irq 12 on acpi0 > psm0: current command byte:0047 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model GlidePoint, device ID 0-00, 2 buttons > psm0: config:00000000, flags:00000000, packet size:3 > psm0: syncmask:c0, syncbits:00 > acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0 > fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 > on acpi0 > unknown: not probed (disabled) > sio0: irq maps: 0x1 0x11 0x1 0x1 > sio0 port 0x3f8-0x3ff irq 4 on acpi0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > sio1: irq maps: 0x1 0x1 0x1 0x1 > sio1 port 0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > unknown: not probed (disabled) > unknown: not probed (disabled) > unknown: not probed (disabled) > Trying Read_Port at 203 > Trying Read_Port at 243 > Trying Read_Port at 283 > Trying Read_Port at 2c3 > Trying Read_Port at 303 > Trying Read_Port at 343 > Trying Read_Port at 383 > Trying Read_Port at 3c3 > ex_isa_identify() > isa_probe_children: disabling PnP devices > isa_probe_children: probing non-PnP devices > orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0 > sc0: <System console> on isa0 > sc0: VGA <16 virtual consoles, flags=0x0> > sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > fb0: vga0, vga, type:VGA (5), flags:0x7007f > fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 > fb0: init mode:24, bios mode:3, current mode:24 > fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k > vga0: vga: WARNING: video mode switching is not fully supported on this adapter > VGA parameters upon power-up > 50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 83 > b4 1f 00 4f 0d 0e 00 00 07 80 91 87 8f 28 1f 8f > b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff > VGA parameters in BIOS for mode 24 > 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 > bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 > b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff > EGA/VGA parameters to be used for mode 24 > 50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 83 > b4 1f 00 4f 0d 0e 00 00 07 80 91 87 8f 28 1f 8f > b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff > isa_probe_children: probing PnP devices > BIOS Geometries: > 0:02d8fe3f 0..728=729 cylinders, 0..254=255 heads, 1..63=63 sectors > 0 accounted for > Device configuration finished. > procfs registered > Timecounters tick every 10.000 msec > bpf: lo0 attached > acpi_cpu0: set speed to 100.0% > acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5% > acpi_acad0: On Line > pccard0: CIS version PCCARD 2.0 or 2.1 > pccard0: CIS info: NETGEAR, FA410TX, Fast Ethernet > pccard0: Manufacturer code 0x149, product 0x230 > pccard0: function 0: network adapter, ccr addr 400 mask b > pccard0: function 0, config table entry 32: I/O card; irq mask befc; iomask 5, iospace 0-1f; > mwait_required rdybsy_active wp_active bvd_active io16 irqlevel > pccard0: function 0, config table entry 1: I/O card; irq mask befc; iomask a, iospace 300-31f; > mwait_required rdybsy_active wp_active bvd_active io16 irqlevel > pccard0: function 0, config table entry 2: I/O card; irq mask befc; iomask a, iospace 320-33f; > mwait_required rdybsy_active wp_active bvd_active io16 irqlevel > pccard0: function 0, config table entry 3: I/O card; irq mask befc; iomask a, iospace 340-35f; > mwait_required rdybsy_active wp_active bvd_active io16 irqlevel > pccard0: function 0, config table entry 4: I/O card; irq mask befc; iomask a, iospace 380-39f; > mwait_required rdybsy_active wp_active bvd_active io16 irqlevel > ed0: <Linksys Etherfast 10/100 Ethernet> at port 0x100-0x11f irq 3 function 0 config 32 on > pccard0 > bpf: ed0 attached > ed0: address 00:e0:98:7e:60:10, type Linksys (16 bit) > ukphy0: <Generic IEEE 802.3u media interface> on miibus0 > ukphy0: OUI 0x0010dd, model 0x0001, rev. 2 > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > ad0: success setting UDMA2 on Intel chip > Creating DISK ad0 > ar: FreeBSD check1 failed > ad0: <TOSHIBA MK6015MAP/U8.12 A> ATA-5 disk at ata0-master > ad0: 5729MB (11733120 sectors), 12416 C, 15 H, 63 S, 512 B > ad0: 16 secs/int, 1 depth queue, UDMA33 > ad0: piomode=4 dmamode=2 udmamode=4 cblid=1 > Mounting root from ufs:/dev/ad0s2a > ad0s1: type 0xb, start 63, end = 3357584, size 3357522 : OK > ad0s2: type 0xa5, start 3357585, end = 11727449, size 8369865 : OK > start_init: trying /sbin/init > ed0: device timeout > Linux ELF exec handler installed > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-current" in the body of the message -- John Baldwin <jhb@FreeBSD.org> <>< http://www.FreeBSD.org/~jhb/ "Power Users Use the Power to Serve!" - http://www.FreeBSD.org/ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?XFMail.20021001220335.jhb>