Date: Wed, 29 Dec 2010 03:10:59 +0800 (SGT) From: Darmawan Salihun <darmawan_salihun@yahoo.com> To: John Baldwin <jhb@freebsd.org> Cc: freebsd-hackers@freebsd.org Subject: Re: PCI IDE Controller Base Address Register setting Message-ID: <964892.49841.qm@web76809.mail.sg1.yahoo.com> In-Reply-To: <201012281352.31367.jhb@freebsd.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi, =0A=0A--- On Tue, 12/28/10, John Baldwin <jhb@freebsd.org> wrote:=0A=0A= > From: John Baldwin <jhb@freebsd.org>=0A> Subject: Re: PCI IDE Controller = Base Address Register setting=0A> To: "Darmawan Salihun" <darmawan_salihun@= yahoo.com>=0A> Cc: freebsd-hackers@freebsd.org=0A> Date: Tuesday, December = 28, 2010, 1:52 PM=0A> On Tuesday, December 28, 2010 1:38:05=0A> pm Darmawan= Salihun wrote:=0A> > Hi,=0A> > =0A> > --- On Tue, 12/28/10, John Baldwin <= jhb@freebsd.org>=0A> wrote:=0A> > =0A> > > From: John Baldwin <jhb@freebsd.= org>=0A> > > Subject: Re: PCI IDE Controller Base Address=0A> Register sett= ing=0A> > > To: freebsd-hackers@freebsd.org=0A> > > Cc: "Darmawan Salihun" = <darmawan_salihun@yahoo.com>=0A> > > Date: Tuesday, December 28, 2010, 10:2= 0 AM=0A> > > On Monday, December 27, 2010 6:07:35=0A> > > am Darmawan Salih= un wrote:=0A> > > > Hi, =0A> > > > =0A> > > > I'm trying to install FreeBSD= 8.0 on AMD=0A> Geode LX800=0A> > > (CS5536 "southbridge"). =0A> > > Howeve= r, it cannot detect the IDE controller (in=0A> the=0A> > > CS5536) correctl= y. It =0A> > > says something similar to this: =0A> > > > "IDE controller n= ot present"=0A> > > =0A> > > Hmm, I can't find a message like that=0A> anyw= here.=A0 Can=0A> > > you get the exact message =0A> > > you are seeing?=0A>= > > =0A> > =0A> > It says: =0A> > =0A> > "No disks found! Please verify th= at your disk=0A> controller is being properly=0A> > probed at boot time."= =0A> =0A> Oh, so this is a message from the installer.=A0 Can you=0A> captu= re a verbose dmesg=0A> via a serial console perhaps?=A0 =0A=0AI'm not sure = if I can do this because I've tried a couple of times =0Abut nothing comes = out of the serial console. Perhaps a wrong baud rate setting? =0AI set it t= o 96bps and 8-N-1 back then. Is that correct? =0A=0A> Or at least the kerne= l=0A> probe messages for your=0A> ATA controller?=0A> =0A=0AI recall that p= ressing Alt+F2 during the installation would open-up =0Aanother console, fu= ll with log messages. Would that be enough? =0A=0AThanks, =0A=0ADarmawan=0A= =0A=0A=0A> -- =0A> John Baldwin=0A> _______________________________________= ________=0A> freebsd-hackers@freebsd.org=0A> mailing list=0A> http://lists.= freebsd.org/mailman/listinfo/freebsd-hackers=0A> To unsubscribe, send any m= ail to "freebsd-hackers-unsubscribe@freebsd.org"=0A> =0A=0A=0A
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?964892.49841.qm>