Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 09 Feb 2007 09:23:41 -0800
From:      Mark Atkinson <atkin901@yahoo.com>
To:        freebsd-current@freebsd.org
Subject:   Re: nve related LOR triggered by lots of small packets, and a hard hang
Message-ID:  <eqiamu$5lo$1@sea.gmane.org>
References:  <20070110120731.GA1515@shark.localdomain> <200701100910.13167.jhb@freebsd.org> <20070110155331.GA2762@shark.localdomain> <20070111004044.GA33964@cdnetworks.co.kr> <eqdn24$ck$1@sea.gmane.org>

next in thread | previous in thread | raw e-mail | index | archive | help
Mark Atkinson wrote:

> Pyun YongHyeon wrote:
> 
>> On Wed, Jan 10, 2007 at 06:53:31PM +0300, Sergey Zaharchenko wrote:
>>  > Hello John!
>>  > 
>>  > Wed, Jan 10, 2007 at 09:10:12AM -0500 you wrote:
>>  > [snip]
>>  > > Have you tried using nfe(4)? :)
>>  > 
>>  > Now I have, and it works just fine, thanks (I somehow thought nfe was
>>  > specific to some platform). Why isn't it the default? Smaller range of
>>  > hardware supported?
>>  > 
>> 
>> AFAIK, nfe(4) supports more hardwares than that of nve(4).
>> Try overhauled nfe(4) in the following URL.
>> 
>> http://people.freebsd.org/~yongari/nfe/if_nfe.c
>> http://people.freebsd.org/~yongari/nfe/if_nfereg.h
>> http://people.freebsd.org/~yongari/nfe/if_nfevar.h
>> 
>> The patch fixed serveral bugs in nfe(4) and it should perform better
>> than nve(4). The following hardware features are supported.
>>  o TSO
>>  o Tx/Rx IP/TCP/UDP checksum offload
>>  o VLAN hardware tag insertion/stripping
>>  o Jumbo frame(up to 9100 bytes)
>> 
>> It seems that the hardware supports MSI/MSI-X too but I don't have
>> nForce hardwares that supports MSI/MSI-X so it's hard to implement/
>> experiment it. Accoring to the Shigeaki Tagashira, the author of
>> FreeBSD nfe(4), his hardware claims to support 8 messages. I've
>> checked Linux forcedeth driver to get hardware information for
>> MSI/MSI-X but it I cound't understand the details. :-(
>> 
> 
> I've been running into this hardlock LOR a lot recently on a  TYAN 2895
> (K8WE) based box.   So I tried your patch to nfe on today's -current.   I
> tried a couple of small packet ping floods to a lan neighbor under nfe and
> it survived.   Did fine with some large NFS over TCP transfers as well.
> However, I'll leave it up and running to see if it keels over in the
> future.
> 
> pci128: <ACPI PCI bus> on pcib6
> pci128: physical bus=128
> found-> vendor=0x10de, dev=0x005e, revid=0xa3
>         bus=128, slot=0, func=0
>         class=05-80-00, hdrtype=0x00, mfdev=0
>         cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
>         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found-> vendor=0x10de, dev=0x00d3, revid=0xa3
>         bus=128, slot=1, func=0
>         class=05-80-00, hdrtype=0x00, mfdev=1
>         cmdreg=0x000f, statreg=0x00a0, cachelnsz=0 (dwords)
>         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>         map[14]: type 1, range 32, base 0xd8400000, size 12, enabled
> found-> vendor=0x10de, dev=0x0057, revid=0xa3
>         bus=128, slot=10, func=0
>         class=06-80-00, hdrtype=0x00, mfdev=0
>         cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
>         lattimer=0x00 (0 ns), mingnt=0x01 (250 ns), maxlat=0x14 (5000 ns)
>         intpin=a, irq=5
>         powerspec 2  supports D0 D1 D2 D3  current D0
>         map[10]: type 1, range 32, base 0xd8401000, size 12, enabled
>         map[14]: type 4, range 32, base 0x3000, size  3, enabled
> pcib6: matched entry for 128.10.INTA (src \\_SB_.PCI1.LMAC:0)
> pci_link22: Picked IRQ 52 with weight 0
> ioapic3: Changing polarity for pin 20 to high
> pcib6: slot 10 INTA routed to irq 52 via \\_SB_.PCI1.LMAC
> found-> vendor=0x10de, dev=0x005d, revid=0xa3
>         bus=128, slot=14, func=0
>         class=06-04-00, hdrtype=0x01, mfdev=0
>         cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
>         lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
>         powerspec 2  supports D0 D3  current D0
>         MSI supports 2 messages, 64 bit
> pci128: <memory> at device 0.0 (no driver attached)
> pci128: <memory> at device 1.0 (no driver attached)
> nfe1: <NVIDIA nForce4 CK804 MCP9 Networking Adapter> port 0x3000-0x3007
> mem 0xd8
> 401000-0xd8401fff irq 52 at device 10.0 on pci128
> nfe1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xd8401000
> nfe1: bpf attached
> e1: Ethernet address: 00:e0:81:57:d9:af
> miibus1: <MII bus> on nfe1
> e1000phy1: <Marvell 88E1111 Gigabit PHY> PHY 1 on miibus1
> e1000phy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
> 1000baseTX-FDX, auto
> ioapic3: routing intpin 20 (PCI IRQ 52) to vector 57
> nfe1: [MPSAFE]
> nfe1: [FAST]

After a day of running this, it became obvious the nfe driver patch has some
sort of issue, at least with -current and this board.  Although NFS speeds
seemed reasonable, transfers over TCP from a webserver suffered some sort
of very noticeable pause/send/pause/send...  type problem that reduced
transfers to about 6Kbyte/s.  This problem went away when putting nve back
into the kernel and retrying the same scenerio. 

-- 
Mark Atkinson
atkin901@yahoo.com
(!wired)?(coffee++):(wired);




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?eqiamu$5lo$1>