Skip site navigation (1)Skip section navigation (2)
Date:      Sat, 20 Mar 2004 12:53:51 +0800 (HKT)
From:      Spencer Chan <hmchan@alumni.cuhk.edu.hk>
To:        "stable@freebsd.org" <stable@freebsd.org>
Subject:   Re: ATI Radeon 9600 SE & OpenGL?
Message-ID:  <20040320124834.E11836@amd>
In-Reply-To: <405BADFC.2020704@barryp.org>
References:  <7670000.1079480581@palle.girgensohn.se> <13770000.1079537744@rambutan.pingpong.net> <33830000.1079712277@durian.pingpong.net> <405B2D7A.5050309@barryp.org><405BADFC.2020704@barryp.org>

next in thread | previous in thread | raw e-mail | index | archive | help
Just to add some data point, i have

~#pciconf -l -v|egrep agp\|drm
agp0@pci0:0:0:  class=0x060000 card=0x00000000 chip=0x30991106 rev=0x00
hdr=0x00
drm0@pci1:0:0:  class=0x030000 card=0x017018bc chip=0x59641002 rev=0x01
hdr=0x00
~#dmesg |grep drm
drm0: <ATI Radeon RV280 9200 SE> port 0xa000-0xa0ff mem
0xe1000000-0xe100ffff,0xd0000000-0xd7ffffff irq 11 at device 0.0 on pci1
info: [drm] AGP at 0xc0000000 256MB
info: [drm] Initialized radeon 1.10.0 20020828 on minor 0
info: [drm] Loading R200 Microcode
drm0: [MPSAFE]
info: [drm] Loading R200 Microcode

My system is RELENG_5_2, with src/sys/dev/drm/radeon* updated to HEAD to
recognize my card's PCI id. I am using XFree86 4.4 binaries.

However my glxgear framerate is slower than what i got with r128 on the
same system. But it works anyways.


On Fri, 19 Mar 2004, Barry Pederson wrote:

> Stijn Hoop wrote:
>
> >>So does the 3D acceleration actually work in your setup?
> >
> > It does in mine:
> >
> > agp0: <Intel 82845 host to AGP bridge> mem 0xf8000000-0xfbffffff at device 0.0 on pci0
> >
> > later after starting X:
> >
> > drm0: <ATI Radeon RV280 9200 SE> port 0xd800-0xd8ff mem 0xdf000000-0xdf00ffff,0xf0000000-0xf7ffffff irq 11 at device 0.0 on pci1
> >
> > And glxgears gets me an acceptable framerate. Unfortunately I'm not at the
> > console or I'd show you the numbers.
> >
> > I just put this card in the machine last week and I had to upgrade to
> > XFree86-4-Server-snap port but other than that I didn't do anything fancy
> > iirc.
> >
> > XF86Config attached fwiw.
> >
> > HTH,
> >
> > --Stijn
>
>
> Thanks, having a known-working configuration to sure helps, but after
> taking your config and just reducing the "Modes" list in the "Screen"
> section to something my monitor can handle - I still get the same
> result, a hard hang with a black screen.
>
>
>
> Jamie Bowden wrote:
>
>  >>I end up just pulling the power cord and then letting it
>  >>reboot and go through a fsck.
>  >
>  >
>  > Instead, hold the power button down for ~15 seconds.  Much less
>  > trauma on the hardware than pulling the plug.
>
> Thanks, that's good to know - ended up giving that a try too :)
>
> 	Barry
> _______________________________________________
> freebsd-stable@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"
>



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040320124834.E11836>