Date: Mon, 11 Feb 2002 14:38:31 -0500 (EST) From: "G. Wright" <wrightg@mcmail.cis.mcmaster.ca> To: freebsd <george@vagner.com> Cc: Geoff Wright <wrightg@mcmaster.ca>, <questions@freebsd.org> Subject: Re: Not able to make fbsd recognize two NICS Message-ID: <Pine.SOL.4.33.0202111436510.7736-100000@mcmail.cis.mcmaster.ca> In-Reply-To: <014c01c1b327$0658e4b0$0400a8c0@thunderbird>
next in thread | previous in thread | raw e-mail | index | archive | help
Thank you all for the help. It turned out that the SMC NIC had "jumper settings" which allowed me to set that card to read at irq 3. Take care, geoff On Mon, 11 Feb 2002, freebsd wrote: > maybe both are on IRQ10 ? > > try changing the 3com to a different irq not being used > such as irq5 using the dos software supplied on their site. > > > > ed0 at port 0x280-0x29f iomem 0xd8000-oxdbfff irq 10 on isa0 > ed0: address 00:00:c0:17:c3:4e, type WD8013EPC (16 bit) > > ep0: <3Com 3C509-Combo EtherLink III> at port 0x300-0x30f irq 10 on isa0 > ep0: Ethernet address 00:20:af:03:a9:42 > > > > ----- Original Message ----- > From: "Geoff Wright" <wrightg@mcmaster.ca> > To: <questions@FreeBSD.ORG> > Sent: Monday, February 11, 2002 10:56 AM > Subject: Not able to make fbsd recognize two NICS > > > > Hi, > > > > Summary: > > > > 1. Installed two NICs into 486DX (with the hope of eventually sharing an > > internet connection with my linux box) > > > > 2. Individually they both work fine > > > > 3. When they are both physically present in the machine, only one is > > recognized > > > > 4. attempted a couple of fixes by compiling a new kernel > > > > > > Explanation: > > > > Newbie here. And I apologize in advance because I don't have all of the > > jargon straight. I have successfully installed FreeBSD 4.4-Release on an > old > > 486DX that came my way. Initially, I had a SMC 83C690LJ NIC in the > machine > > which was recognized fine during the install. > > > > (aside: I am behind a Linksys 4-port Router set to DHCP on a home > > network...Also, attached to that SMC NIC, I have a CentreCom 210T Twisted > > Pair Transceiver which apparently takes a RJ45 cable into a "serial?" (15 > > pin) port on the network card. How can I describe this "serial15 pin > > port"...this NIC has a BNC port on it and also this "serial 15 pin port", > > there was no RJ45 port on the card and that is why I am using the Twisted > > Pair Transceiver described above which converts the "serial" port into a > RJ45 > > port - I hope that makes sense.) > > > > The SMC NIC is picked up as: > > ed0 at port 0x280-0x29f iomem 0xd8000-oxdbfff irq 10 on isa0 > > ed0: address 00:00:c0:17:c3:4e, type WD8013EPC (16 bit) > > > > I just unplug the DSL cable from my linux box which is sitting beside the > 486 > > on my desk and plug it into the SMC NIC to see if freebsd and the NIC are > > working properly. Voila! I can ftp and use Lynx - how exciting! > > > > Next, eventually I would like to be able to share this DSL line my freeBSD > > machine (the 486) and the better box running Linux-mandrake 8.0 (without > > having to crawl under the desk at switch it by hand :-)). The 486 is > > primarily just to hack around and learn on without the risk of losing > > anything too important. At the moment, I can't afford to be messing > around > > too much with my linux box because I need it for work. > > > > I physically removed the SMC card from the 486 and plugged in a 3Com > > 3c509-Combo Etherlink III NIC with a rj45, "serial?" and BNC port. I > wanted > > to find out how and where it was recognized by freeBSD. Anyways, it is > > picked up as: > > > > ep0: <3Com 3C509-Combo EtherLink III> at port 0x300-0x30f irq 10 on isa0 > > ep0: Ethernet address 00:20:af:03:a9:42 > > > > So, the next experiment was to plug both cards in at the same time and see > if > > they would both be picked up. > > > > At this point, I was still using the GENERIC kernel, and so made sure that > > both ed0 and ep were not commented out. I say ep instead of ep0 because in > > the GENERIC kernel, the line for ep is just: > > device ep > > whereas for ed0 it is: > > device ed0 at isa? port 0x280 irq 10 iomem 0xd8000 > > > > I rebooted my machine and waited anxiously to see what would > happen...well, > > ep0 driver appeared in the inital boot-up stuff but ed0 was nowhere to be > > found. Unfortunately, I cannot provide the output from dmesg easily (as I > > haven't figured out how to send an email from freebsd...I am sending this > > email from my linux box...that will be next weekend's project!) > > > > I tried a couple of other little moves but they were totally just > > guesswork...so I don't know how useful it would be for me to write it out. > > > > Any thoughts or help would be greatly appreciated. > > Thank you in advance. > > geoff > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-questions" in the body of the message > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.SOL.4.33.0202111436510.7736-100000>