Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 2 Mar 2009 14:53:42 +0100
From:      Hans Petter Selasky <hselasky@c2i.net>
To:        freebsd-current@freebsd.org
Cc:        Nenhum_de_Nos <matheus@eternamente.info>
Subject:   Re: problem on usb boot from mini itx
Message-ID:  <200903021453.44367.hselasky@c2i.net>
In-Reply-To: <f8161e633a32c1fcde0661afb816cbcb.squirrel@cygnus.homeunix.com>
References:  <f8161e633a32c1fcde0661afb816cbcb.squirrel@cygnus.homeunix.com>

next in thread | previous in thread | raw e-mail | index | archive | help
On Monday 02 March 2009, Nenhum_de_Nos wrote:
> hail,
>
> I'm trying to make a router from a mini itx, but can't get it to boot from
> usb disk or stick. I can boot from usb cdrom and install ok, 7.1 and 7.0.
> but when I try to boot, I get to the point:
>
> F1 FreeBSD
>
> and press enter.
>
> then I get:
> Can't work out which disk we are booting from.
> Guessed BIOS device 0x80 not found by probes, defaulting to disk0:
>
> can't load 'kernel'
>
> Type '?' for a list of commands, 'help' for more detailed help.
> OK
>
> lsdev gives me:
>
> cd devices:
> disk devices:
> pxe devices:
>
> so, I got to the point it can't find my usb disk, but I don't know why as
> in boot cd it says the disk0 ok. so I copied all cd boot stuff
> (boot/cdboot/etc) to see if I can use that to again see my disk, but I got
> nowhere :(
>
> I used the usb disk on other pc and all went fine, even compiled current
> (my target branch) to see if most recent usb boot things (read some from
> two threads here, not got deep though) and also nothing :(
>
> is there anything I can do ?
>
> dmesg follows
>
> thanks,
>
> matheus
>
> the dmesg:
>
> Copyright (c) 1992-2009 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> 	The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 8.0-CURRENT #0: Sun Mar  1 22:52:45 BRT 2009
>     root@cygnus.apartnet:/usr/obj/usr/src/sys/Cygnus8
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Transmeta(tm) Crusoe(tm) Processor TM5700 (798.13-MHz 586-class CPU)
>   Origin = "GenuineTMx86"  Id = 0x543  Stepping = 3
>   Features=0x84893f<FPU,VME,DE,PSE,TSC,MSR,CX8,SEP,CMOV,PN,MMX>
> real memory  = 117374976 (111 MB)
> avail memory = 100130816 (95 MB)
> kbd1 at kbdmux0
> pcib0: <Host to PCI bridge> pcibus 0 on motherboard
> pir0: <PCI Interrupt Routing Table: 5 Entries> on motherboard
> pci0: <PCI bus> on pcib0
> pci0: <memory, RAM> at device 0.1 (no driver attached)
> pci0: <memory, RAM> at device 0.2 (no driver attached)
> pci0: <memory, RAM> at device 0.3 (no driver attached)
> uhci0: <VIA 83C572 USB controller> port 0xe000-0xe01f irq 15 at device 9.0
> on pci0
> uhci0: [ITHREAD]
> uhci0: LegSup = 0x201a
> usbus0: <VIA 83C572 USB controller> on uhci0
> uhci1: <VIA 83C572 USB controller> port 0xe100-0xe11f irq 5 at device 9.1
> on pci0
> uhci1: [ITHREAD]
> uhci1: LegSup = 0x2010
> usbus1: <VIA 83C572 USB controller> on uhci1
> ehci0: <VIA VT6202 USB 2.0 controller> mem 0xe8131000-0xe81310ff irq 10 at
> device 9.2 on pci0
> ehci0: [ITHREAD]
> usbus2: EHCI version 1.0
> usbus2: <VIA VT6202 USB 2.0 controller> on ehci0
> vgapci0: <VGA-compatible display> port 0xe200-0xe2ff mem
> 0xe0000000-0xe7ffffff,0xe8120000-0xe812ffff irq 11 at device 13.0 on pci0
> isab0: <PCI-ISA bridge> at device 17.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <VIA 8231 UDMA100 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe300-0xe30f at device 17.1 on pci0
> ata0: <ATA channel 0> on atapci0
> ata0: [ITHREAD]
> ata1: <ATA channel 1> on atapci0
> ata1: [ITHREAD]
> pci0: <bridge> at device 17.4 (no driver attached)
> vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xe600-0xe6ff mem
> 0xe8130000-0xe81300ff irq 15 at device 18.0 on pci0
> vr0: Quirks: 0x0
> vr0: Revision: 0x51
> miibus0: <MII bus> on vr0
> ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
> ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> vr0: Ethernet address: 00:13:21:ee:26:00
> vr0: [ITHREAD]
> cpu0 on motherboard
> pmtimer0 on isa0
> atrtc0: <AT realtime clock> at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 irq 1 pnpid
> PNP0303 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> unknown: <PNP0c01> can't assign resources (memory)
> orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xcc000-0xd5fff pnpid
> ORM0000 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> ppc0: parallel port not found.
> unknown: <PNP0c01> can't assign resources (memory)
> Timecounter "TSC" frequency 798131036 Hz quality 800
> Timecounters tick every 1.000 msec
> usbus0: 12Mbps Full Speed USB v1.0
> usbus1: 12Mbps Full Speed USB v1.0
> usbus2: 480Mbps High Speed USB v2.0
> ugen0.1: <VIA> at usbus0
> ushub0: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
> ugen1.1: <VIA> at usbus1
> ushub1: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
> ugen2.1: <VIA> at usbus2
> ushub2: <VIA EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
> ad0: 6149MB <SAMSUNG SV0643D KT100> at ata0-master UDMA33
> GEOM: ad0s1: geometry does not match label (255h,63s != 15h,63s).
> ushub0: 2 ports with 2 removable, self powered
> ushub1: 2 ports with 2 removable, self powered
> Root mount waiting for: usbus2
> Root mount waiting for: usbus2
> ushub2: 4 ports with 4 removable, self powered
> Trying to mount root from ufs:/dev/ad0s1a
> usb2_alloc_device:1463: set address 2 failed (ignored)
> usb2_alloc_device:1499: getting device descriptor at addr 2 failed!
> usb2_req_re_enumerate:1414: addr=2, set address failed! (ignored)
> usb2_req_re_enumerate:1427: getting device descriptor at addr 2 failed!
> usb2_req_re_enumerate:1414: addr=2, set address failed! (ignored)
> usb2_req_re_enumerate:1427: getting device descriptor at addr 2 failed!
> ugen0.2: <> at usbus0 (disconnected)
> uhub_reattach_port:414: could not allocate new device!

Hi,

What happens if you put an external USB HUB in between ?

There is also a ehci.no_hs sysctl which you can try setting to one.

Also try enabling uhub debugging during boot.

sysctl hw.usb2.uhub.debug=15

--HPS



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200903021453.44367.hselasky>