Date: Wed, 14 Feb 1996 11:33:20 +0500 From: Richard J Kuhns <rjk@sparcmill.grauel.com> To: "Justin T. Gibbs" <gibbs@freefall.freebsd.org> Cc: freebsd-stable@freebsd.org Subject: Re: One problem && one question Message-ID: <9602141633.AA00264@sparcmill.grauel.com> In-Reply-To: <199602140522.VAA08632@freefall.freebsd.org> References: <9602131927.AA23929@sparcmill.grauel.com> <199602140522.VAA08632@freefall.freebsd.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Justin T. Gibbs writes:
> Ahh. It did make a difference. Unfortunately, when I was cleaning
> up the bt driver, I assumed that the PCI probe would always return
> one of the ISA compatibility addresses. As Rod pointed out, this is
> not always the case. This patch should do the trick
>
... and there was great rejoicing. Here's the dmesg output; I find it
interesting that the isa probe code apparently still tries to look for a bt
card.
Thanks a lot.
--
Rich Kuhns rjk@grauel.com
PO Box 6249
100 Sawmill Road
Lafayette, IN 47903
(317)477-6000 x319
==
FreeBSD 2.1-STABLE #0: Wed Feb 14 11:25:54 EST 1996
rjk@watson.grauel.com:/prog/2.1-STABLE/src/sys/compile/BTTEST
CPU: 100-MHz Pentium 815\\100 (Pentium-class CPU)
Origin = "GenuineIntel" Id = 0x525 Stepping=5
Features=0x1bf<FPU,VME,PSE,MCE,CX8,APIC>
real memory = 33554432 (32768K bytes)
avail memory = 30728192 (30008K bytes)
pcibus_setup(1): mode1res=0x80000000 (0x80000000), mode2res=0xff (0x0e)
pcibus_setup(2): mode1res=0x80000000 (0x80000000)
pcibus_check: device 0 is there (id=04061039)
Probing for devices on PCI bus 0:
configuration mode 1 allows 32 devices.
chip0 <SiS 85c501> rev 0 on pci0:0
chip1 <SiS 85c503> rev 0 on pci0:1
bt0 <Buslogic 946 SCSI host adapter> rev 0 int a irq 10 on pci0:13
mapreg[10] type=1 addr=00006000 size=ffff0004.
bt0: Bt946C/ 0-(32bit) bus
bt0: reading board settings, busmastering, int=10
bt0: version 4.25J, fast sync, parity, 32 mbxs, 32 ccbs
bt0: targ 0 sync rate=10.00MB/s(100ns), offset=15
bt0: targ 5 sync rate= 5.00MB/s(200ns), offset=11
bt0: Using Strict Round robin scheme
bt0 waiting for scsi devices to settle
(bt0:0:0): "MICROP 3243-19MZ Q4D HT02" type 0 fixed SCSI 2
sd0(bt0:0:0): Direct-Access 4095MB (8388315 512 byte sectors)
sd0(bt0:0:0): with 3956 cyls, 19 heads, and an average 111 sectors/track
(bt0:5:0): "EXABYTE EXB-82058VQANXR1 0790" type 1 removable SCSI 2
st0(bt0:5:0): Sequential-Access density code 0x0, drive empty
(bt0:6:0): "Chinon CD-ROM CDS-525 V09" type 5 removable SCSI 2
cd0(bt0:6:0): CD-ROM
cd0(bt0:6:0): UNIT ATTENTION asc:2a,0 Parameters changed
cd present.[400000 x 2048 byte records]
pci0: uses 4 bytes of I/O space from 6000 upto 6003.
Probing for devices on the ISA bus:
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA color <16 virtual consoles, flags=0x0>
ed0 at 0x280-0x29f irq 5 maddr 0xd8000 msize 16384 on isa
ed0: address 00:00:c0:15:00:ab, type SMC8216/SMC8216C (16 bit)
sio0 at 0x3f8-0x3ff irq 4 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
pca0 on motherboard
pca0: PC speaker audio driver
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: NEC 72065B
fd0: 1.44MB 3.5in
bt: unit number (1) too high
bt0 not found at 0x330
npx0 on motherboard
npx0: INT 16 interface
changing root device to sd0a
BIOS Geometries:
0:03ff3f20 0..1023=1024 cylinders, 0..63=64 heads, 1..32=32 sectors
0 accounted for
sd0s1: type 0xa5, start 0, end = 8388314, size 8388315 : OK
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?9602141633.AA00264>