Date: Sun, 15 Jul 2012 22:11:06 +0200 From: Marco Steinbach <coco@executive-computing.de> To: freebsd-sparc64@freebsd.org Subject: Sun Blade 1000 fan control Message-ID: <500323DA.4010205@executive-computing.de>
next in thread | raw e-mail | index | archive | help
Hi, I've installed 9.0-RELEASE on a Blade 1000, installation was quick and completely painless, the installer even warned me about a possibly wrong choice during customized partitioning -- thumbs up to nwhitehorn@ and anyone else involved. While I realize this being a very minor issue compared to the efforts neccessary for supporting this arch and machine to the extend given, I'd really like to be able to have, preferably automagic, RPM control over the fans of the box. Searching the archives, I found the topic already was discussed in 2011. Alas, it seems as if there's been no noticeable change in that since then. I'd very much like to see this functionality included in FreeBSD, but am unable to offer more than assistance, by e.g. testing out possible patches or giving direct (serial/ssh) access to the machine. If there's any other use for this kind of direct access, I'd be more than glad to be of assistance. I need the Solaris side of things sometimes, though, so the machine wouldn't be permanently available. Here's some more info on the machine: sb1000# uname -a FreeBSD sb1000.c0c0.intra 9.0-RELEASE FreeBSD 9.0-RELEASE #0: Wed Jan 4 05:26:33 UTC 2012 root@heller.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC sparc64 sb1000# dmesg Copyright (c) 1992-2012 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.0-RELEASE #0: Wed Jan 4 05:26:33 UTC 2012 root@heller.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC sparc64 real memory = 1073741824 (1024 MB) avail memory = 1025843200 (978 MB) cpu0: Sun Microsystems UltraSparc-III Processor (750.00 MHz CPU) cpu1: Sun Microsystems UltraSparc-III Processor (750.00 MHz CPU) FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs kbd0 at kbdmux0 nexus0: <Open Firmware Nexus device> pcib0: <Sun Host-PCI bridge> mem 0x40004700000-0x40004717fff,0x40004410000-0x4000441004f,0x7ffee000000-0x7ffee0000ff irq 563,560,561,564,550 on nexus0 pcib0: Schizo, version 4, IGN 0x8, bus B, PCI mode, 33MHz pcib0: DVMA map: 0xc0000000 to 0xffffffff 131072 entries pci0: <OFW PCI bus> on pcib0 ebus0: <PCI-EBus3 bridge> mem 0x7d000000-0x7dffffff,0x7e000000-0x7e7fffff at device 5.0 on pci0 pcib1: <Sun Host-PCI bridge> mem 0x40004600000-0x40004617fff,0x40004410000-0x4000441004f,0x7ffec000000-0x7ffec0000ff irq 562,560,561,564,551 on nexus0 pcib1: Schizo, version 4, IGN 0x8, bus A, PCI mode, 66MHz Timecounter "pcib1" frequency 150000000 Hz quality 100 pcib1: DVMA map: 0xc0000000 to 0xffffffff 131072 entries pci1: <OFW PCI bus> on pcib1 upa0: <UPA bridge> mem 0x40004480000-0x4000448001f,0x40004706000-0x4000470600f,0x40004708000-0x4000470800f on nexus0 nexus0: <memory-controller> mem 0x40000400000-0x40000400047 type memory-controller (no driver attached) nexus0: <memory-controller> mem 0x40000c00000-0x40000c00047 type memory-controller (no driver attached) ebus0: <flashprom> addr 0-0x1fffff (no driver attached) ebus0: <bbc> addr 0x100000000-0x1000fffff (no driver attached) ebus0: <ppm> addr 0x10000000e-0x100000028,0x100728000-0x100728003,0x10030002e-0x10030002f,0x100300600-0x100300607 (no driver attached) ebus0: <i2c> addr 0x10000002e-0x10000002f,0x10000002d irq 35 (no driver attached) ebus0: <i2c> addr 0x100000030-0x100000031 irq 35 (no driver attached) ebus0: <beep> addr 0x100000032-0x100000037 (no driver attached) pcm0: <Sun Audiocs> addr 0x100200000-0x1002000ff,0x100702000-0x10070200f,0x100704000-0x10070400f,0x100722000-0x100722003 irq 32,33 on ebus0 pcm0: <CS4231A Codec Id. 10> rtc0: <Real-Time Clock> addr 0x100300070-0x100300071 irq 36 on ebus0 ebus0: <gpio> addr 0x100300600-0x100300607 (no driver attached) ebus0: <pmc> addr 0x100300700-0x100300701 (no driver attached) ebus0: <floppy> addr 0x1003023f0-0x1003023f7,0x100706000-0x10070600f,0x100720000-0x100720003 irq 37 (no driver attached) ebus0: <parallel> addr 0x100300278-0x100300287,0x10030002e-0x10030002f,0x100700000-0x10070000f irq 28 (no driver attached) scc0: <Siemens SAB 82532 dual channel SCC> addr 0x100400000-0x10040007f irq 34 on ebus0 uart0: <SAB 82532 v3.2, channel A> on scc0 uart0: CTS oflow uart0: console (9600,n,8,1) uart1: <SAB 82532 v3.2, channel B> on scc0 uart1: CTS oflow gem0: <Sun ERI 10/100 Ethernet> mem 0x100000-0x11ffff at device 5.1 on pci0 miibus0: <MII bus> on gem0 ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0 ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow gem0: 2kB RX FIFO, 2kB TX FIFO gem0: Ethernet address: 00:03:ba:09:0f:b4 fwohci0: <Sun PCIO-2> mem 0x120000-0x1207ff,0x122000-0x1227ff at device 5.2 on pci0 fwohci0: OHCI version 1.0 (ROM=0) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:03:ba:ff:fe:09:0f:b4 fwohci0: Phy 1394a available S400, 4 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 dcons_crom0: <dcons configuration ROM> on firewire0 dcons_crom0: bus_addr 0xc113c000 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:03:ba:09:0f:b4 fwe0: Ethernet address: 02:03:ba:09:0f:b4 fwip0: <IP over FireWire> on firewire0 fwip0: Firewire address: 00:03:ba:ff:fe:09:0f:b4 @ 0xfffe00000000, S400, maxrec 2048 fwohci0: Initiate bus reset fwohci0: fwohci_intr_core: BUS reset fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode ohci0: <Sun PCIO-2 USB controller> mem 0x1000000-0x1007fff at device 5.3 on pci0 usbus0: <Sun PCIO-2 USB controller> on ohci0 sym0: <875> port 0x300-0x3ff mem 0x124000-0x1240ff,0x126000-0x126fff at device 6.0 on pci0 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym1: <875> port 0x400-0x4ff mem 0x128000-0x1280ff,0x12a000-0x12afff at device 6.1 on pci0 sym1: No NVRAM, ID 7, Fast-20, SE, parity checking machfb0: <ATI Rage XL> port 0x500-0x5ff mem 0x2000000-0x2ffffff,0x12c000-0x12cfff at device 1.0 on pci0 machfb0: 8 MB aperture at 0xe5d1e000 swapped machfb0: 8188 KB SGRAM 114.992 MHz, maximum RAMDAC clock 230 MHz, DSP machfb0: resolution 1152x900 at 8 bpp machfb1: <ATI Rage XL> port 0x600-0x6ff mem 0x3000000-0x3ffffff,0x12e000-0x12efff at device 2.0 on pci0 machfb1: 8 MB aperture at 0xe6d20000 swapped machfb1: 8188 KB SGRAM 114.992 MHz, maximum RAMDAC clock 230 MHz, DSP machfb1: resolution 1152x900 at 8 bpp isp0: <Qlogic ISP 2200 PCI FC-AL Adapter> port 0x300-0x3ff mem 0x100000-0x100fff at device 4.0 on pci1 isp0: invalid NVRAM header isp0: invalid NVRAM header isp0: bad frame length (0) from NVRAM- using 1024 isp0: bad execution throttle of 0- using 16 schppm0: <Schizo power management> mem 0x40004410050-0x40004410057 on nexus0 syscons0: <System console> on nexus0 syscons0: Unknown <16 virtual consoles, flags=0x100> Timecounter "tick" frequency 750000000 Hz quality 10 Timecounter "stick" frequency 5000000 Hz quality 10 Event timer "tick" frequency 750000000 Hz quality 1000 Timecounters tick every 1.000 msec firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me) firewire0: bus manager 0 usbus0: 12Mbps Full Speed USB v1.0 ugen0.1: <SUN> at usbus0 uhub0: <SUN OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 uhub0: 4 ports with 4 removable, self powered SMP: AP CPU #1 Launched! da0 at isp0 bus 0 scbus2 target 0 lun 0 da0: <HPQ BF07258243 HP01> Fixed Direct Access SCSI-3 device da0: 100.000MB/s transfers WWNN 0x20000011c664a175 WWPN 0x21000011c664a175 PortID 0xe4 da0: Command Queueing enabled da0: 70007MB (143374738 512 byte sectors: 255H 63S/T 8924C) Trying to mount root from ufs:/dev/da0a [rw]... sb1000# pciconf -lv hostb0@pci0:0:0:0: class=0x060000 card=0x00000000 chip=0x8001108e rev=0x00 hdr=0x00 vendor = 'Oracle Corporation' device = 'Schizo PCI Bus Module' class = bridge subclass = HOST-PCI ebus0@pci0:0:5:0: class=0x068000 card=0x00000000 chip=0x1100108e rev=0x01 hdr=0x00 vendor = 'Oracle Corporation' device = 'RIO EBUS' class = bridge gem0@pci0:0:5:1: class=0x020000 card=0x00000000 chip=0x1101108e rev=0x01 hdr=0x00 vendor = 'Oracle Corporation' device = 'RIO 10/100 Ethernet [eri]' class = network subclass = ethernet fwohci0@pci0:0:5:2: class=0x0c0010 card=0x00000000 chip=0x1102108e rev=0x01 hdr=0x00 vendor = 'Oracle Corporation' device = 'RIO 1394' class = serial bus subclass = FireWire ohci0@pci0:0:5:3: class=0x0c0310 card=0x00000000 chip=0x1103108e rev=0x01 hdr=0x00 vendor = 'Oracle Corporation' device = 'RIO USB' class = serial bus subclass = USB sym0@pci0:0:6:0: class=0x010000 card=0x00000000 chip=0x000f1000 rev=0x37 hdr=0x00 vendor = 'LSI Logic / Symbios Logic' device = '53c875' class = mass storage subclass = SCSI sym1@pci0:0:6:1: class=0x010000 card=0x00000000 chip=0x000f1000 rev=0x37 hdr=0x00 vendor = 'LSI Logic / Symbios Logic' device = '53c875' class = mass storage subclass = SCSI machfb0@pci0:0:1:0: class=0x030000 card=0x00000000 chip=0x47521002 rev=0x27 hdr=0x00 vendor = 'ATI Technologies Inc' device = 'Rage XL' class = display subclass = VGA machfb1@pci0:0:2:0: class=0x030000 card=0x00000000 chip=0x47521002 rev=0x27 hdr=0x00 vendor = 'ATI Technologies Inc' device = 'Rage XL' class = display subclass = VGA hostb1@pci1:0:0:0: class=0x060000 card=0x00000000 chip=0x8001108e rev=0x00 hdr=0x00 vendor = 'Oracle Corporation' device = 'Schizo PCI Bus Module' class = bridge subclass = HOST-PCI isp0@pci1:0:4:0: class=0x010000 card=0x00000000 chip=0x22001077 rev=0x05 hdr=0x00 vendor = 'QLogic Corp.' device = 'QLA2200 64-bit Fibre Channel Adapter' class = mass storage subclass = SCSI sb1000#
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?500323DA.4010205>