Date: Sat, 26 Jun 2004 01:46:45 +0200 From: Bernd Walter <ticso@cicely5.cicely.de> To: freebsd-alpha@freebsd.org Subject: init in malloc(): error: recursive call Message-ID: <20040625234643.GA73421@cicely5.cicely.de>
next in thread | raw e-mail | index | archive | help
After updating from march (and >100 days uptime):
(boot dka300.3.0.1.1)
block 0 of dka300.3.0.1.1 is a valid boot block
reading 15 blocks from dka300.3.0.1.1
bootstrap code read in
Building FRU table
base = 200000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 1f2000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Loading /boot/loader
Console: SRM firmware console
VMS PAL rev: 0x4000200010115
OSF PAL rev: 0x4000200020117
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM disk boot, Revision 1.2
(ticso@cicely12.cicely.de, Tue Mar 16 04:58:54 CET 2004)
Memory: 2228224 k
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x3d6a50+0x2f470 syms=[0x8+0x4f320+0x8+0x421ab]
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Entering /boot/kernel/kernel at 0xfffffc000033ebc0...
sio1: gdb debugging port
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2-CURRENT #0: Fri Jun 25 23:20:56 CEST 2004
ticso@cicely12.cicely.de:/var/d3/obj/var/d3/c12-2004-06-25/src/sys/CICELY12
Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc000079a000.
AlphaServer 4100
AlphaServer 4100 5/533 4MB, 531MHz
8192 byte page size, 3 processors.
CPU: EV56 (21164A) major=7 minor=2 extensions=0x1<BWX>
OSF PAL rev: 0x4000200020117
real memory = 2097152000 (2000 MB)
avail memory = 2048909312 (1953 MB)
FreeBSD/SMP: Multiprocessor System Detected: 3 CPUs
random: <entropy source, Software, Yarrow>
mcbus0: <MCBUS Backplane Bus>
pcib0: <MCPCIA PCI Adapter> at mcbus0 gid 7 mid 5
pcib0: Horse Revision 3, Left Handed Saddle Revision 0, CAP Revision 1
pci0: <PCI bus> on pcib0
sym0: <810> port 0x1ffde00-0x1ffdeff mem 0x7df6e00-0x7df6eff at device 1.0 on pci0
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: interrupting at IRQ 0x10 (vec 0xb40)
sym0: [GIANT-LOCKED]
pcib2: <PCI-PCI bridge> at device 2.0 on pci0
pci2: <PCI bus> on pcib2
isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x1ffef00-0x1ffefff mem 0x7eef000-0x7eeffff at device 0.0 on pci2
pcib2: slot 0 INTA is routed to irq 0
isp0: interrupting at IRQ 0x0 (vec 0xb80)
isp0: [GIANT-LOCKED]
sym1: <875> port 0x1ffdf00-0x1ffdfff mem 0x7df7000-0x7df7fff,0x7df6f00-0x7df6fff at device 3.0 on pci0
sym1: Tekram NVRAM, ID 7, Fast-20, SE, parity checking
sym1: interrupting at IRQ 0x4 (vec 0xbc0)
sym1: [GIANT-LOCKED]
pcib3: <PCI-PCI bridge> at device 4.0 on pci0
pci3: <PCI bus> on pcib3
pci3: <mass storage, SCSI> at device 4.0 (no driver attached)
pci3: <memory> at device 5.0 (no driver attached)
pci3: <mass storage, SCSI> at device 8.0 (no driver attached)
pci3: <mass storage, SCSI> at device 12.0 (no driver attached)
pcib1: <MCPCIA PCI Adapter> at mcbus0 gid 7 mid 4
pcib1: Horse Revision 3, Left Handed Saddle Revision 0, CAP Revision 1
pci1: <PCI bus> on pcib1
illegal PCI extended capability offset 8266240
eisab0: <PCI-EISA bridge> at device 1.0 on pci1
eisa0: <EISA bus> on eisab0
mainboard0: <DEC6400 (System Board)> on eisa0 slot 0
isa0: <ISA bus> on eisab0
pci1: <mass storage, SCSI> at device 2.0 (no driver attached)
fxp0: <Intel 82559 Pro/100 Ethernet> port 0x1fffe00-0x1fffe3f mem 0x7e00000-0x7efffff,0x7dde000-0x7ddefff at device 3.0 on pci1
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:90:27:a2:6d:db
fxp0: interrupting at IRQ 0x4 (vec 0x9c0)
fxp0: [GIANT-LOCKED]
pci1: <mass storage, SCSI> at device 5.0 (no driver attached)
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: interrupting at ISA irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Polled port
ppi0: <Parallel I/O> on ppbus0
ppc0: interrupting at ISA irq 7
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A, console
sio0: interrupting at ISA irq 4
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio1: interrupting at ISA irq 3
Timecounter "i8254" frequency 1193182 Hz quality 0
Timecounters tick every 0.833 msec
Waiting 15 seconds for SCSI devices to settle
sa0 at sym1 bus 0 target 0 lun 0
sa0: <EXABYTE EXB-8500SMBANXH1 0458> Removable Sequential Access SCSI-2 device
sa0: 4.032MB/s transfers (4.032MHz, offset 11)
sa1 at sym1 bus 0 target 1 lun 0
sa1: <EXABYTE EXB-8500SMBANXH1 0458> Removable Sequential Access SCSI-2 device
sa1: 4.032MB/s transfers (4.032MHz, offset 11)
sa2 at sym1 bus 0 target 2 lun 0
sa2: <HP HP35470A 1109> Removable Sequential Access SCSI-2 device
sa2: 5.000MB/s transfers (5.000MHz, offset 8)
sa3 at sym1 bus 0 target 3 lun 0
sa3: <HP C1533A 9503> Removable Sequential Access SCSI-2 device
sa3: 10.000MB/s transfers (10.000MHz, offset 8)
sa4 at sym1 bus 0 target 4 lun 0
sa4: <HP HP35470A T503> Removable Sequential Access SCSI-2 device
sa4: 5.000MB/s transfers (5.000MHz, offset 8)
da0 at sym0 bus 0 target 3 lun 0
da0: <SEAGATE ST11200N SUN1.05 9500> Fixed Direct Access SCSI-2 device
da0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
da0: 1005MB (2059140 512 byte sectors: 64H 32S/T 1005C)
da1 at isp0 bus 0 target 1 lun 0
da1: <SEAGATE ST43400N 1028> Fixed Direct Access SCSI-2 device
da1: 10.000MB/s transfers (10.000MHz, offset 12), Tagged Queueing Enabled
da1: 2777MB (5688447 512 byte sectors: 255H 63S/T 354C)
da4 at isp0 bus 0 target 5 lun 0
da4: <SEAGATE ST43400N 1028> Fixed Direct Access SCSI-2 device
da4: 10.000MB/s transfers (10.000MHz, offset 12), Tagged Queueing Enabled
da4: 2777MB (5688447 512 byte sectors: 255H 63S/T 354C)
da3 at isp0 bus 0 target 4 lun 0
da3: <SEAGATE ST43400N 1028> Fixed Direct Access SCSI-2 device
da3: 10.000MB/s transfers (10.000MHz, offset 12), Tagged Queueing Enabled
da3: 2777MB (5688447 512 byte sectors: 255H 63S/T 354C)
da2 at isp0 bus 0 target 2 lun 0
da2: <SEAGATE ST43400N 1028> Fixed Direct Access SCSI-2 device
da2: 10.000MB/s transfers (10.000MHz, offset 12), Tagged Queueing Enabled
da2: 2777MB (5688447 512 byte sectors: 255H 63S/T 354C)
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
Mounting root from ufs:/dev/da0a
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
init in malloc(): error: recursive call
[...] many more of them and then it stops.
OK - I had MAXDSIZ and DFLDSIZ raised in my config to 1.8G, but
this really shouldn't be too much for an alpha and it worked bevor.
I tried reducing the settings from loader and removing the kernel
options without luck :(
--
B.Walter BWCT http://www.bwct.de
bernd@bwct.de info@bwct.de
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040625234643.GA73421>