Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 25 May 2011 16:04:53 +0200
From:      Willy Offermans <Willy@Offermans.Rompen.nl>
To:        Jeremy Chadwick <freebsd@jdc.parodius.com>
Cc:        Willy Offermans <Willy@offermans.rompen.nl>, freebsd-stable@FreeBSD.ORG, freebsd-hardware@FreeBSD.ORG
Subject:   Re: modem support MT9234ZPX-PCIE-NV
Message-ID:  <20110525140453.GD3842@vpn.offrom.nl>
In-Reply-To: <20110522071642.GA61515@icarus.home.lan>
References:  <20110521092037.GB3271@vpn.offrom.nl> <20110522071642.GA61515@icarus.home.lan>

next in thread | previous in thread | raw e-mail | index | archive | help

--7iMSBzlTiPOCCT2k
Content-Type: text/plain; charset=utf-8
Content-Disposition: inline
Content-Transfer-Encoding: 8bit

Hello Jeremy and FreeBSD friends,

On Sun, May 22, 2011 at 12:16:42AM -0700, Jeremy Chadwick wrote:
> On Sat, May 21, 2011 at 11:20:37AM +0200, Willy Offermans wrote:
> > Dear FreeBSD friends,
> > 
> > I need support with a MultiTech modem, MT9234ZPX-PCIE-NV
> > (http://www.multitech.com/en_US/PRODUCTS/Families/MultiModemZPX/)
> > 
> > The modem is recognised during the boot event:
> > 
> > <snip>
> > pci6: <simple comms, UART> at device 0.0 (no driver attached)
> > </snip>
> > 
> > and also appears in the list of found hardware over the PCI bus:
> > 
> > <snip>
> > none1@pci0:6:0:0:       class=0x070002 card=0x20262205 chip=0x015213a8 rev=0x02 hdr=0x00
> >     vendor     = 'Exar Corp.'
> >     device     = 'XR17C/D152 Dual PCI UART'
> >     class      = simple comms
> >     subclass   = UART
> > </snip>
> > 
> > However, as the boot process already mentions, there is no driver attached
> > and I cannot get the modem to appear as an accessible and functional
> > device. Is there someone, who can help me to get this modem to work?
> 
> It would be helpful if you could specify what FreeBSD version you're
> using.
> 
> Assuming 8.2 or RELENG_8: no promises, but puc(4) is probably what
> you're looking for.  I would try adding:
> 
> puc_load="yes"
> 
> To your /boot/loader.conf, then see what happens after booting.  uart(4)
> may auto-attach to that.  Again, no promises.
> 
> -- 
> | Jeremy Chadwick                                   jdc@parodius.com |
> | Parodius Networking                       http://www.parodius.com/ |
> | UNIX Systems Administrator                  Mountain View, CA, USA |
> | Making life hard for others since 1977.               PGP 4BD6C0CB |
> 

I'm using FreeBSD 7.2-RELEASE-p2. I have enclosed the dmesg.boot file.

puc was already incorporated into the kernel:

kosmos# kldload -v puc
kldload: can't load puc: File exists

So I assume puc has already been loaded.

-- 
Met vriendelijke groeten,
With kind regards,
Mit freundlichen Gruessen,
De jrus wah,

Willy

*************************************
Dr. W.K. Offermans
CAT Postdoctoral Fellow
CAT Catalytic Center
Institut für Technische und Makromolekulare Chemie
RWTH Aachen
Worringerweg 1, Raum 38C-150
D-52074 Aachen, Germany
Phone:  +49 241 80 28592
Fax:    +49 241 80 22593
Home:   +31 45 544 49 44
Mobile: +31 681 15 87 68
e-mail: Willy@Offermans.Rompen.nl
e-mail: Willy.Offermans@CatalyticCenter.RWTH-Aachen.de

                                       Powered by ....

                                            (__)
                                         \\\'',)
                                           \/  \ ^
                                           .\._/_)

                                       www.FreeBSD.org

--7iMSBzlTiPOCCT2k
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.boot"

Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...0 0 done
All buffers synced.
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.2-RELEASE-p2 #3: Thu May 12 16:15:47 CEST 2011
    willy@kosmos.rompen.nl:/usr/obj/usr/src/sys/KOSMOS
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU           X3360  @ 2.83GHz (2266.76-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0x1067a  Stepping = 10
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x408e3fd<SSE3,RSVD2,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,<b19>,XSAVE>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
  Cores per package: 4
usable memory = 4285059072 (4086 MB)
avail memory  = 4116738048 (3926 MB)
ACPI APIC Table: <082608 APIC0956>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
 cpu2 (AP): APIC ID:  2
 cpu3 (AP): APIC ID:  3
This module (opensolaris) contains code covered by the
Common Development and Distribution License (CDDL)
see http://opensolaris.org/os/licensing/opensolaris_license/
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <082608 RSDT0956> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, dff00000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci5: <ACPI PCI bus> on pcib1
pcib2: <PCI-PCI bridge> at device 0.0 on pci5
pci6: <PCI bus> on pcib2
pci6: <simple comms, UART> at device 0.0 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci4: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci3: <ACPI PCI bus> on pcib4
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x4201> mem 0xfbef0000-0xfbefffff irq 16 at device 0.0 on pci3
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge0: Ethernet address: 00:24:8c:66:4b:62
bge0: [ITHREAD]
pcib5: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pci2: <ACPI PCI bus> on pcib5
bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x4201> mem 0xfbdf0000-0xfbdfffff irq 17 at device 0.0 on pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1: Ethernet address: 00:24:8c:66:4c:48
bge1: [ITHREAD]
uhci0: <UHCI (generic) USB controller> port 0xcc00-0xcc1f irq 23 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xd000-0xd01f irq 19 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0xd080-0xd09f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xfbbff800-0xfbbffbff irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib6
vgapci0: <VGA-compatible display> port 0xec00-0xec7f mem 0xf4000000-0xf7ffffff,0xfbcc0000-0xfbcfffff at device 3.0 on pci1
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
atapci1: <Intel ICH7 SATA300 controller> port 0xdc00-0xdc07,0xd880-0xd883,0xd800-0xd807,0xd480-0xd483,0xd400-0xd40f mem 0xfbbffc00-0xfbbfffff irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
cpu0: <ACPI CPU> on acpi0
ACPI Warning (tbutils-0243): Incorrect checksum in table [OEMB] -  67, should be 64 [20070320]
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
cpu2: <ACPI CPU> on acpi0
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
cpu3: <ACPI CPU> on acpi0
est3: <Enhanced SpeedStep Frequency Control> on cpu3
p4tcc3: <CPU Frequency Thermal Control> on cpu3
orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0
ppc0: cannot reserve I/O port range
WARNING: ZFS is considered to be an experimental feature in FreeBSD.
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert enabled, nat loadable, rule-based forwarding disabled, default to deny, logging limited to 10 packets/entry by default
ZFS filesystem version 6
ZFS storage pool version 6
ad4: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata2-master SATA150
ad5: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata2-slave SATA150
ad6: 953869MB <SAMSUNG HD103UJ 1AA01113> at ata3-master SATA150
GEOM_LABEL: Label for provider ad4s1a is ufsid/4a6b25f55a113d71.
acd0: DVDR <TSSTcorp CDDVDW SH-S223B/SB00> at ata3-slave SATA150
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #3 Launched!
Trying to mount root from zfs:tank/root
tap0: Ethernet address: 00:bd:45:09:00:00
GEOM_LABEL: Label ufsid/4a6b25f55a113d71 removed.
GEOM_LABEL: Label for provider ad4s1a is ufsid/4a6b25f55a113d71.
GEOM_LABEL: Label ufsid/4a6b25f55a113d71 removed.
bge0: link state changed to UP
bge1: link state changed to UP

--7iMSBzlTiPOCCT2k--



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20110525140453.GD3842>